Basic Configuration 1401 topics

A place to discuss basic configurations like probe input, homing etc.

Subject	Replies / Views	Last Post
Tandem Axis with one Home/Limit switch Topic started 03 Sep 2020 23:54, by palador Last Post 04 Sep 2020 11:03 by palador	Replies:2 Views:1233	palador Last Post by palador 04 Sep 2020 11:03
Chinese 3040Z-DQ parallel port CNC router Config troubles Topic started 29 Aug 2020 03:28, by gfiber Last Post 31 Aug 2020 23:11 by gfiber	Replies:2 Views:1195	gfiber Last Post by gfiber 31 Aug 2020 23:11
Working with mesa 7i76e Topic started 28 Aug 2020 16:05, by Jocman Last Post 30 Aug 2020 09:30 by Jocman	Replies:2 Views:1003	Jocman Last Post by Jocman 30 Aug 2020 09:30
Tool table offsets, Z axis limit exceeded with G43, but program runs ok Topic started 27 Aug 2020 23:54, by kapucin Last Post 28 Aug 2020 15:54 by kapucin	Replies:1 Views:775	kapucin Last Post by kapucin 28 Aug 2020 15:54
Initial Coordinates Topic started 23 Aug 2020 18:20, by AgentWD40 Last Post 26 Aug 2020 14:15 by AgentWD40	Replies:4 Views:682	Last Post by AgentWD40 26 Aug 2020 14:15
Deactivate or increase the soft limit Topic started 22 Aug 2020 11:47, by cyberspaceschwabe Last Post 22 Aug 2020 20:42 by tommylight	Replies:5 Views:689	Last Post by tommylight 22 Aug 2020 20:42
Trapezoidal home limit actuators (or not) Topic started 17 Aug 2020 15:55, by rootboy Last Post 18 Aug 2020 14:41 by rootboy	Replies:5 Views:689	Last Post by rootboy 18 Aug 2020 14:41
Can't get lathe closed loop servo spindle working (torque mode servo) Topic started 14 Aug 2020 13:38, by pippin88 Last Post 16 Aug 2020 02:44 by pippin88	Replies:7 Views:938	pippin88 Last Post by pippin88 16 Aug 2020 02:44
Homing Modifications Topic started 31 Jul 2020 23:30, by destruction_cereal Last Post 01 Aug 2020 17:45 by tommylight	Replies:5 Views:798	Last Post by tommylight 01 Aug 2020 17:45
Pncconf, howto setup for Mesa 5i25, 6i25, 7i92 using parallel port/BOB/G540 Topic started 28 Apr 2020 14:55, by tommylight Last Post 31 Jul 2020 11:38 by tommylight 1 2	Replies:13 Views:6692	Last Post by tommylight 31 Jul 2020 11:38
Release home switch then return to almost the trigger position? Topic started 29 Jul 2020 23:56, by nick-parker Last Post 31 Jul 2020 04:54 by cmorley	Replies:4 Views:665	cmorley Last Post by cmorley 31 Jul 2020 04:54
General network issue affecting 7i76e connection Topic started 26 Jul 2020 13:09, by simonmn Last Post 27 Jul 2020 20:27 by rodw	Replies:7 Views:1126	Last Post by rodw 27 Jul 2020 20:27
Turning: limit rpm Topic started 23 Jul 2020 07:50, by jsskangas Last Post 24 Jul 2020 07:37 by jsskangas	Replies:3 Views:747	jsskangas Last Post by jsskangas 24 Jul 2020 07:37
Working Gantry (2 motors - 1 axis) CNC router w. Mesa 7i76e Topic started 01 Apr 2018 22:21, by tripwire Last Post 23 Jul 2020 18:22 by ki4swy	Replies:8 Views:2070	ki4swy Last Post by ki4swy 23 Jul 2020 18:22
another pci parallel card configuraion issue Topic started 11 Jul 2020 22:11, by jruffsr Last Post 15 Jul 2020 12:28 by Todd Zuercher	Replies:3 Views:862	Last Post by Todd Zuercher 15 Jul 2020 12:28
G-Code Newbie Question Topic started 10 Jul 2020 16:30, by Project_Hopeless Last Post 11 Jul 2020 18:31 by Project_Hopeless	Replies:7 Views:1034	Last Post by Project_Hopeless 11 Jul 2020 18:31
What input should I use for a probe fault. Topic started 08 Jul 2020 23:56, by oldtech Last Post 10 Jul 2020 19:11 by tommylight 1 2	Replies:17 Views:1857	Last Post by tommylight 10 Jul 2020 19:11
A axis rotab setup Topic started 05 Jul 2020 19:53, by JR1050 Last Post 07 Jul 2020 16:52 by JR1050	Replies:2 Views:754	Last Post by JR1050 07 Jul 2020 16:52
Setting up 7I73 Pendent Topic started 04 Jul 2020 23:30, by MarkD2 Last Post 04 Jul 2020 23:51 by PCW	Replies:1 Views:767	Last Post by PCW 04 Jul 2020 23:51
automatic generation backlash table from linear encoder? Topic started 23 Jun 2020 20:47, by idea Last Post 24 Jun 2020 04:36 by Aciera	Replies:1 Views:680	Last Post by Aciera 24 Jun 2020 04:36

Time to create page: 0.430 seconds