Why the circle drawed by "G2 X390 Y-280 I5 J0" not round?

More
5 years 2 weeks ago #223057 by curran209
Why the circle drawed by "G2 X390 Y-280 I5 J0" not round? was created by curran209
We use laser to draw circle on a aluminum sheet. Trajectory planning is round, but the circle drawed is not round.
Why the circle drawed by "G2 X390 Y-280 I5 J0" not round?

Please Log in to join the conversation.

More
5 years 2 weeks ago #223077 by tommylight
Replied by tommylight on topic Why the circle drawed by "G2 X390 Y-280 I5 J0" not round?
Very low acceleration or mechanical issues.

Please Log in to join the conversation.

More
5 years 2 weeks ago #223080 by RNJFAB
Replied by RNJFAB on topic Why the circle drawed by "G2 X390 Y-280 I5 J0" not round?
x & y axis not square

Please Log in to join the conversation.

More
5 years 2 weeks ago #223094 by andypugh
Replied by andypugh on topic Why the circle drawed by "G2 X390 Y-280 I5 J0" not round?
This could be simple geometry. Is the laser controlled by a galvanometer or is it moving on a cartesian axis?

If it is a galvanometer then the only place that a circle will be circular is exactly under the centre of the galvanometer.

This can presumably be corrected by a kinematics module.

Please Log in to join the conversation.

More
5 years 2 weeks ago #223145 by curran209
Replied by curran209 on topic Why the circle drawed by "G2 X390 Y-280 I5 J0" not round?
The laser binded on the Z axis. Laser is on all the time. Draw this circle by moving the X and Y axis of servo motor.

Please Log in to join the conversation.

More
5 years 2 weeks ago #223159 by curran209
Replied by curran209 on topic Why the circle drawed by "G2 X390 Y-280 I5 J0" not round?
@tommylignt I increased acceleration, but it didn't to be good.
Excluded mechanical issues, because another CNC has not this issue.

@RNJFAB x & y axis is square

Please Log in to join the conversation.

More
5 years 2 weeks ago #223175 by andypugh
Replied by andypugh on topic Why the circle drawed by "G2 X390 Y-280 I5 J0" not round?
Can you use Halscope to plot the X and Y following errors?

Please Log in to join the conversation.

More
5 years 1 week ago #223440 by curran209
Replied by curran209 on topic Why the circle drawed by "G2 X390 Y-280 I5 J0" not round?
sorry, can you tell me how to download Halscope and use it?

Please Log in to join the conversation.

More
5 years 1 week ago #223448 by andypugh
Replied by andypugh on topic Why the circle drawed by "G2 X390 Y-280 I5 J0" not round?
It's part of LinuxCNC.

linuxcnc.org/docs/2.8/html/hal/tutorial....ec:tutorial-halscope

Most GUIs can open it from the menu, or you can open it from the command line as described above.

Please Log in to join the conversation.

More
5 years 1 week ago #223536 by curran209
Replied by curran209 on topic Why the circle drawed by "G2 X390 Y-280 I5 J0" not round?
what is  the variable name of x axis and y axis following errors in halscope?
which is the selection of x axis and y axis following errors  in in pin, signal, param?

Attachment not found

Attachment not found

Attachment not found

Please Log in to join the conversation.

Time to create page: 0.069 seconds
Powered by Kunena Forum