Basic Configuration 1230 topics

A place to discuss basic configurations like probe input, homing etc.

Subject	Replies / Views	Last Post
Error in log Category: Basic Configuration Topic started 2 years 3 months ago, by anli Last Post 2 years 3 months ago by andypugh	Replies:1 Views:1456	Last Post by andypugh 2 years 3 months ago
Baffling Issue With Torch Not Firing When It Should And Firing When It Should'nt Category: Basic Configuration Topic started 2 years 3 months ago, by cnctrucker Last Post 2 years 3 months ago by cnctrucker 1 2	Replies:10 Views:2895	Last Post by cnctrucker 2 years 3 months ago
RC Servo Test with 7i96s Category: Basic Configuration Topic started 2 years 3 months ago, by Project_Hopeless Last Post 2 years 3 months ago by andypugh	Replies:1 Views:884	Last Post by andypugh 2 years 3 months ago
Safety relay and e-stop in LCNC? Category: Basic Configuration Topic started 2 years 3 months ago, by thomaseg Last Post 2 years 3 months ago by thomaseg	Replies:8 Views:3615	Last Post by thomaseg 2 years 3 months ago
M-codes location Category: Basic Configuration Topic started 2 years 3 months ago, by eduard Last Post 2 years 3 months ago by Aciera	Replies:6 Views:1158	Last Post by Aciera 2 years 3 months ago
How to aggregate several counters Category: Basic Configuration Topic started 2 years 3 months ago, by OGMaker Last Post 2 years 3 months ago by OGMaker	Replies:2 Views:987	Last Post by OGMaker 2 years 3 months ago
Simple ATC help Category: Basic Configuration Topic started 2 years 3 months ago, by tomala89 Last Post 2 years 3 months ago by Aciera	Replies:3 Views:2364	Last Post by Aciera 2 years 3 months ago
mesaCT, 7i95t and SPINx Category: Basic Configuration Topic started 2 years 9 months ago, by DK8DE Last Post 2 years 3 months ago by AirRacer	Replies:8 Views:2094	Last Post by AirRacer 2 years 3 months ago
spindle doesn’t work Category: Basic Configuration Topic started 2 years 3 months ago, by mnikulski Last Post 2 years 3 months ago by mnikulski 1 2	Replies:12 Views:2973	Last Post by mnikulski 2 years 3 months ago
shared limit switch and home get ignored during homing Category: Basic Configuration Topic started 2 years 3 months ago, by mnikulski Last Post 2 years 3 months ago by mnikulski	Replies:4 Views:1363	Last Post by mnikulski 2 years 3 months ago
MPG Jogging Category: Basic Configuration Topic started 2 years 3 months ago, by B.Reilly01 Last Post 2 years 3 months ago by B.Reilly01	Replies:2 Views:1004	Last Post by B.Reilly01 2 years 3 months ago
MPCNC help with Homing switches on LPT board Category: Basic Configuration Topic started 2 years 4 months ago, by dredivan Last Post 2 years 4 months ago by andypugh	Replies:1 Views:1247	Last Post by andypugh 2 years 4 months ago
Set Feed Override to 0 every cycle start Category: Basic Configuration Topic started 7 years 11 months ago, by mydani Last Post 2 years 4 months ago by Thayloreing	Replies:9 Views:3353	Last Post by Thayloreing 2 years 4 months ago
Prevent spindle start if a certain tool is selected? Category: Basic Configuration Topic started 6 years 1 week ago, by JetForMe Last Post 2 years 4 months ago by RotarySMP 1 2 3 4	Replies:30 Views:6591	Last Post by RotarySMP 2 years 4 months ago
7i92 configuration with two daughter card Category: Basic Configuration Topic started 2 years 4 months ago, by rajsekhar Last Post 2 years 4 months ago by rajsekhar	Replies:8 Views:1441	Last Post by rajsekhar 2 years 4 months ago
Mesa 7i95t and 7i83 Analogue servo card Category: Basic Configuration Topic started 2 years 7 months ago, by NT4Boy Last Post 2 years 5 months ago by NT4Boy 1 2 3	Replies:24 Views:4985	Last Post by NT4Boy 2 years 5 months ago
Different acceleration across joints Category: Basic Configuration Topic started 2 years 5 months ago, by pavel7890 Last Post 2 years 5 months ago by pavel7890	Replies:2 Views:1018	Last Post by pavel7890 2 years 5 months ago
Help wiring up BLDC drives with BISSC linear encoder to 6i25_7i76_7i74 Category: Basic Configuration Topic started 2 years 5 months ago, by pmchetan Last Post 2 years 5 months ago by pmchetan 1 2	Replies:13 Views:3582	Last Post by pmchetan 2 years 5 months ago
motion.spindle vs spindle Category: Basic Configuration Topic started 2 years 5 months ago, by vre Last Post 2 years 5 months ago by andypugh	Replies:1 Views:1080	Last Post by andypugh 2 years 5 months ago
Help in setting up LinuxCNC Category: Basic Configuration Topic started 2 years 5 months ago, by amanker Last Post 2 years 5 months ago by Aciera	Replies:1 Views:1109	Last Post by Aciera 2 years 5 months ago

Time to create page: 0.104 seconds