LinuxCNC start, stop, pause buttons ?

In our shop, we run several CNC mills and lathes. These include Okuma, Tsugami, Fadel, and Daewo. Every one of these machines have prominent green start button and red stop/feed hold buttons, and a reset button that is less prominent

I wonder then, why the decision in LinuxCNC to make the red stup button the stop-and-reset button, instead of just feed hold.

You can just use the Pause button to temporarily pause / feed hold and then resume?

thadwald wrote: I wonder then, why the decision in LinuxCNC to make the red stup button the stop-and-reset button, instead of just feed hold.

You can make physical buttons any colour you want.

Also, LinuxCNC offers a range of user-interfaces. I think you are describing Axis, which is just one of them:

linuxcnc.org/docs/2.7/html/user/user-int...ical_user_interfaces

andypugh wrote: You can make physical buttons any colour you want.

Also, LinuxCNC offers a range of user-interfaces. I think you are describing Axis, which is just one of them:

I have tried Axis but decided to use GMOCCAPY.
I plan to make my physical buttons the colors I described. I am just curious about what led to that UI design in the first place. Does any commercial controller use this design?

The lingering issue is that I now have a big red stop/reset button on the screen, and a big red feed hold/pause physical button.

The colour scheme of any GUI seems to be decided by the GUI author, so only he would know.

I think that it should be fairly easy to change the colours of the buttons, if you want to.

Or you could do this. Examples are here on the forum



I think physical buttons are much better than the GUI ones

rodw wrote: I think physical buttons are much better than the GUI ones

The "Touchy" GUI doesn't give you much choice in the matter. (It _requires_ external run/stop buttons and an MPG)
I see we have the same button supplier (eBay in China
photos.app.goo.gl/M8Lh6PYaJrtu76by5

andypugh wrote:

rodw wrote: I think physical buttons are much better than the GUI ones

The "Touchy" GUI doesn't give you much choice in the matter. (It _requires_ external run/stop buttons and an MPG)
I see we have the same button supplier (eBay in China
photos.app.goo.gl/M8Lh6PYaJrtu76by5

Well actually I got it here oceancontrols.com.au/home.php so probably spent far too much (and they don't seem to sell it anymore)

I think if I did it again, I'd use separate 22mm dia green and say a blue or orange buttons so there is a clear distinction between run/step and estop.

Andy, I have to say when ever I see photos of your lathe, I admire your handiwork.

I set my lathe and router up with a feedhold and cyclestart button. feedhold only pauses program cyclestart will start running of the program and will also resume the program after a program pause. I wanted it to work like my Haas mill.

Here is my hal code snipit for this:

# ******************************
# --- Program Control ---
# ******************************
# --- Cycle start and resume ---
#
net push_cycle_start and2.1.in1 and2.2.in1 <= hm2_5i25.0.7i76.0.0.input-25
net auto_mode_is_set and2.1.in0 not.0.in or2.2.in0 <= halui.mode.is-auto
net invert_auto_mode and2.2.in0 <= not.0.out
net sel_auto_mode halui.mode.auto <= and2.2.out
net interlock_auto_mode and2.3.in0 and2.4.in0 <= and2.1.out
net pgm_is_idle and2.3.in1 <= halui.program.is-idle
net pgm_is_paused and2.4.in1 hm2_5i25.0.7i76.0.0.output-03 <= halui.program.is-paused
net pgm_is_running_invert not.1.in hm2_5i25.0.7i76.0.0.output-01 hm2_5i25.0.7i76.0.0.output-02 <= halui.program.is-running
net pgm_is_running and2.5.in0 and2.6.in0 <= not.1.out
net pgm_idle_interlock and2.5.in1 <= and2.3.out
net pgm_paused_interlock and2.6.in1 <= and2.4.out
net Pgm-Run <= and2.5.out
net Pgm-Resume <= and2.6.out

# --- Program Pause ---

net Pause-Pgm <= hm2_5i25.0.7i76.0.0.input-26

# --- ABORT ---
net Pgm-Stop <= hm2_5i25.0.7i76.0.0.input-27

Here is my control panel for a Router.
Red button is stop .
Green start and resume.
Orange lit is pause or feedhold.