Mint 19.2 update

More
6 years 1 month ago #181908 by billykid
Mint 19.2 update was created by billykid
After a long time I have updated mint 19.2 plasmac. I have set up the BeagleBrainz repositories and updated but lcnc no longer starts.
I am attaching the error file if you can help me.
Thanks in advance
Mauro

Please Log in to join the conversation.

More
6 years 1 month ago #181909 by snowgoer540
Replied by snowgoer540 on topic Mint 19.2 update

billykid wrote: After a long time I have updated mint 19.2 plasmac. I have set up the BeagleBrainz repositories and updated but lcnc no longer starts.
I am attaching the error file if you can help me.
Thanks in advance
Mauro

Can you post your <machine_name>.ini, <machine_name>.hal, <machine_name>_connections.hal files please?

Please Log in to join the conversation.

More
6 years 1 month ago #181910 by billykid
Replied by billykid on topic Mint 19.2 update
here they are
With these files everything worked before updating .. but I have an ssd copy :-)

Please Log in to join the conversation.

  • BeagleBrainz
  • New Member
  • New Member
More
6 years 1 month ago #181911 by BeagleBrainz
Replied by BeagleBrainz on topic Mint 19.2 update
That isn't the most recent version in my repo.
Code:
LINUXCNCVERSION: 2.8.0 LINUXCNC_AUX_GLADEVCP: /usr/share/linuxcnc/aux_gladevcp LINUXCNC_AUX_EXAMPLES: /usr/share/linuxcnc/aux_examples REALTIME: /etc/init.d/realtime RTS: uspace HALLIB_DIR: /usr/share/linuxcnc/hallib dpkg -l '*linuxcnc*': Desired=Unknown/Install/Remove/Purge/Hold | Status=Not/Inst/Conf-files/Unpacked/halF-conf/Half-inst/trig-aWait/Trig-pend |/ Err?=(none)/Reinst-required (Status,Err: uppercase=bad) ||/ Name Version Architecture Description +++-===================-============================-============-===================================================================== un linuxcnc <none> <none> (no description available) ii linuxcnc-build-deps 1:2.8.0~pre1.6143.gcea561bf1 all build-dependencies for linuxcnc un linuxcnc-dev <none> <none> (no description available) un linuxcnc-doc <none> <none> (no description available) ii linuxcnc-doc-en 1:2.8.0 all motion controller for CNC machines and robots (English documentation) un linuxcnc-sim <none> <none> (no description available) un linuxcnc-sim-dev <none> <none> (no description available) ii linuxcnc-uspace 1:2.8.0 amd64 motion controller for CNC machines and robots ii linuxcnc-uspace-dev 1:2.8.0 amd64 PC based motion controller for real-time Linux

When did you setup the repos ?
Have you updated the key from the keyserver as that has changed.
All the ~pre1 packages are no longer in the repo, only the 2.8.0 release is there.

Please Log in to join the conversation.

More
6 years 1 month ago #181922 by billykid
Replied by billykid on topic Mint 19.2 update
I used these .. I'll try again tomorrow calmly.
strange that it gives an error like i386 but it is 64 bit


Import the key:

sudo apt-key adv --keyserver keyserver.ubuntu.com --recv-keys C9F836336AAD909E


Add the source:

sudo add-apt-repository 'deb cnc.beaglebrainz.net/mintcnc/ bionic 2.8-rtpreempt'

Please Log in to join the conversation.

  • BeagleBrainz
  • New Member
  • New Member
More
6 years 1 month ago #181942 by BeagleBrainz
Replied by BeagleBrainz on topic Mint 19.2 update
The packages on my repo are all 64 bit.
Aptget update will mention that there are no 32 bit packages

The repo is good for 64 bit, I test it to make sure it works.

Please Log in to join the conversation.

More
6 years 1 month ago #181981 by billykid
Replied by billykid on topic Mint 19.2 update
Weird because my system looks like 64-bit.
here are my data.
thanks for your interest

Please Log in to join the conversation.

  • BeagleBrainz
  • New Member
  • New Member
More
6 years 1 month ago #181982 by BeagleBrainz
Replied by BeagleBrainz on topic Mint 19.2 update
If this is the message
Code:
N: Skipping acquire of configured file '2.8-rtpreempt/binary-i386/Packages' as repository 'http://cnc.beaglebrainz.net/mintcnc bionic InRelease' doesn't support architecture 'i386'
All that it is saying is that the repo doesn't support i386 and as you are on a 64 bit system, as that is what the kernel is, it is not an issue.
So you are good to update. I did it on my main machine last night.

Please Log in to join the conversation.

More
6 years 1 month ago #181983 by phillc54
Replied by phillc54 on topic Mint 19.2 update
This Unicode error from Axis may point to a translation error:
Code:
Traceback (most recent call last): File "/usr/bin/axis", line 3571, in <module> print _("\nNote:\nIndividual axis homing is not currently supported for") UnicodeEncodeError: 'ascii' codec can't encode character u'\xe8' in position 40: ordinal not in range(128)

It may be worthwhile asking on the Users List:
sourceforge.net/projects/emc/lists/emc-users

Please Log in to join the conversation.

More
6 years 1 month ago #181984 by billykid
Replied by billykid on topic Mint 19.2 update
i did it soon .. i put us language and it works fine. maybe then I'll try to solve but it's not too important.
thanks to you

Please Log in to join the conversation.

Time to create page: 0.199 seconds
Powered by Kunena Forum