[Cutoff] BelongsTo=-1 Climb cut=0 CodeSnip=-1 Comment= Contour method=2 Cut depth=0 Cut direction=0.5 Cutting rules=0 Edge overlap=5 Enabled=0 Feed rate=2000 Finish allowance=0 Grid size=50 ID=-1 Layer= Lead in=-1 Lead in type=0 Lead out=-1 Lead out type=0 Leadins on open paths=0 Length=1 Maximum X size=2000 Maximum Y size=2000 Minimum X size=500 Minimum Y size=500 Name= Offset open paths=0 Optimisation=1 Path rules= Plunge rate=100 Remnants must be rectangular=0 Reverse open paths=0 Start depth=0 Start position=0 Tool=1 Type=RemnantOperation [Cutoff/Custom] [Misc] Count=1 FileVersion=1003 optBias=0.5 Optimisation=0 Template=0 [OpOrder] [Part 0] Angle=0 copyOf=-1 DrawingFile=C:\Users\dean\Documents\Plasma_dxf\spottest.DXF enabled=1 HRef=0 Locked=0 name=spottest VRef=0 XPos=50 YPos=50 [Part 0/GroupSources] [Part 0/Operation0] BelongsTo=-1 Climb cut=0 CodeSnip=-1 Comment= Contour method=2 Coolant=0 Cut depth=0 Cut direction=0.5 Cutting rules=0 Enabled=1 Feed rate=100 Finish allowance=0 ID=0 Layer=holes Lead in=-1 Lead in type=0 Lead out=-1 Lead out type=0 Leadins on open paths=0 Length=1 Max hole size=30 Min hole size=1.62 Name=Drill, holes, T10: 10mm Mild Steel 45A, 0 mm Deep Offset open paths=0 Optimisation=1 Path rules= Peck depth=10 Peck retract=1 Plunge rate=100 Reverse open paths=0 Spindle speed=1000 Start depth=0 Start position=0 Tool=10 Type=DrillOperation [Part 0/Operation0/Custom] [pathRules] GlobalRule=-1 [Table] MaxHeight=1000 Origin=6 RapidSpeed=2000 tableOrigin=6 TableX1=0 TableX2=1000 TableY1=0 TableY2=1000 ToolTime=0 X1=0 X2=1000 Y1=0 Y2=1000 [Tool0] Comment= Cut height=1.5 Feed rate=2000 Kerf width=1.8 Name=1mm Mild steel 45A Pause at end of cut=0 Pierce delay=0.5 Pierce height=3 Pierce type=0 Plunge rate=100 Tool number=1 Type=PlasmaTool Wiggle length=10 [Tool0/Custom] [Tool1] Comment= Cut height=1.5 Feed rate=5500 Kerf width=1.4 Name=2mm mild steel 45A Pause at end of cut=0.5 Pierce delay=0.2 Pierce height=3.8 Pierce type=0 Plunge rate=100 Tool number=2 Type=PlasmaTool Wiggle length=10 [Tool1/Custom] [Tool10] Comment= Cut height=1.5 Feed rate=1300 Kerf width=1.7 Name=8mm Aluminium 45A Pause at end of cut=0.3 Pierce delay=0.6 Pierce height=3.8 Pierce type=1 Plunge rate=100 Tool number=15 Type=PlasmaTool Wiggle length=10 [Tool10/Custom] [Tool11] Comment= Cut height=1.5 Feed rate=850 Kerf width=1.9 Name=10mm Aluminium 45A Pause at end of cut=0.3 Pierce delay=0.7 Pierce height=3.8 Pierce type=1 Plunge rate=100 Tool number=16 Type=PlasmaTool Wiggle length=10 [Tool11/Custom] [Tool2] Comment= Cut height=1.5 Feed rate=3900 Kerf width=1.4 Name=3mm mild steel 45A Pause at end of cut=0.5 Pierce delay=0.2 Pierce height=3.8 Pierce type=0 Plunge rate=100 Tool number=3 Type=PlasmaTool Wiggle length=10 [Tool2/Custom] [Tool3] Comment= Cut height=1.5 Feed rate=2800 Kerf width=1.5 Name=4mm Mild Steel 45A Pause at end of cut=0.5 Pierce delay=0.4 Pierce height=3.8 Pierce type=0 Plunge rate=100 Tool number=4 Type=PlasmaTool Wiggle length=10 [Tool3/Custom] [Tool4] Comment= Cut height=1.5 Feed rate=2100 Kerf width=1.5 Name=5mm Mild Steel 45A Pause at end of cut=0.5 Pierce delay=0.6 Pierce height=3.8 Pierce type=0 Plunge rate=100 Tool number=5 Type=PlasmaTool Wiggle length=10 [Tool4/Custom] [Tool5] Comment= Cut height=1.5 Feed rate=780 Kerf width=1.8 Name=10mm Mild Steel 45A Pause at end of cut=0.3 Pierce delay=0.8 Pierce height=3.8 Pierce type=0 Plunge rate=500 Tool number=10 Type=PlasmaTool Wiggle length=10 [Tool5/Custom] [Tool6] Comment= Cut height=1.5 Feed rate=7800 Kerf width=1.3 Name=2mm Aluminium 45A Pause at end of cut=0.3 Pierce delay=0.1 Pierce height=3.8 Pierce type=0 Plunge rate=100 Tool number=11 Type=PlasmaTool Wiggle length=10 [Tool6/Custom] [Tool7] Comment= Cut height=1.5 Feed rate=4800 Kerf width=1.5 Name=3mm Aluminium 45A Pause at end of cut=0.3 Pierce delay=0.2 Pierce height=3.8 Pierce type=1 Plunge rate=100 Tool number=12 Type=PlasmaTool Wiggle length=10 [Tool7/Custom] [Tool8] Comment= Cut height=1.5 Feed rate=3600 Kerf width=1.5 Name=4mm Aluminium 45A Pause at end of cut=0.3 Pierce delay=0.4 Pierce height=3.8 Pierce type=1 Plunge rate=100 Tool number=13 Type=PlasmaTool Wiggle length=10 [Tool8/Custom] [Tool9] Comment= Cut height=1.5 Feed rate=3000 Kerf width=1.6 Name=5mm Aluminium Pause at end of cut=0.3 Pierce delay=0.5 Pierce height=3.8 Pierce type=1 Plunge rate=100 Tool number=14 Type=PlasmaTool Wiggle length=10 [Tool9/Custom] [ToolChange] BeforeCode= Code= noSafeZ=0 UseX=0 UseY=0 UseZ=0 X=0 Y=0 Z=0 [Variables] [Work] Bottom=0 Clearance=10 isPolygon=0 Notes= Origin=6 ParkUseX=0 ParkUseY=0 ParkUseZ=0 ParkX=0 ParkY=0 ParkZ=0 PlungeSafety=0.5 polyLayer=0 polyPart=0 Thickness=10 X1=0 X2=1400 Y1=0 Y2=1200 [Work/keepout] Clamp Clearance Height=RapidClearance Corner 1X=0 Corner 1Y=0 Corner 2X=0 Corner 2Y=0 Function=0 Inside=1 layer=0 part=0 [BinaryDataStart]%XI@I@2holes>ÀhdÃø—ˆBÀhdÃø—ˆBÀ>À>À>À-DTû!ù? -DTû! @ @#Æ¿D@hdÃø—ˆBÀ>À>À07yÐî6À>À>À-DTû!ù? -DTû!ù¿ @#Æ¿D@>À07yÐî6À07yÐî6À>À>À>À-DTû!ù?  @#Æ¿D@07yÐî6À>À>ÀhdÃø—ˆBÀ>À>À-DTû!ù? -DTû!ù? @#Æ¿D@2holes>À¤{‰vÓ3@.B;ðDDÀ>@>À>@-DTû!ù? -DTû! @ ¸íÀY$@.B;ðDDÀ>@>À.B;ðDD@>À>@-DTû!ù? -DTû!ù¿ ¸íÀY$@>À.B;ðDD@¤{‰vÓ3À>@>À>@-DTû!ù?  ¸íÀY$@¤{‰vÓ3À>@>À¤{‰vÓ3@>À>@-DTû!ù? -DTû!ù? ¸íÀY$@20IÀI@I@I@>À>@-DTû!ù? dä‘w xæ8GI@I@I@IÀ>À>@-DTû! @ dä‘w xæ8GI@IÀIÀIÀ>À>@-DTû!ù¿ dä‘w xæ8GIÀIÀIÀI@>À>@ dä‘w xæ8Gð¿ð¿ÿÿÿÿ>À>À#$ð¿ð¿ÿÿÿÿ>À>@#$