mauro@mauro:~/linuxcnc/configs/qtplasma2$ linuxcnc qtplasma2.ini
LINUXCNC - 2.9.0-pre0-4170-g3c57a16f6
Machine configuration directory is '/home/mauro/linuxcnc/configs/qtplasma2'
Machine configuration file is 'qtplasma2.ini'
Starting LinuxCNC...
Found file(REL): ./qtplasma2.hal
Note: Using POSIX realtime
hm2: loading Mesa HostMot2 driver version 0.15
hm2_eth: loading Mesa AnyIO HostMot2 ethernet driver version 0.2
hm2_eth: 10.10.10.10: INFO: Hardware address (MAC): 00:60:1b:10:00:59
hm2_eth: discovered 7I80DB-16
hm2/hm2_7i80.0: Low Level init 0.15
hm2/hm2_7i80.0: 68 I/O Pins used:
hm2/hm2_7i80.0:     IO Pin 000 (J2-01): Encoder #1, pin B (Input)
hm2/hm2_7i80.0:     IO Pin 001 (J2-14): Encoder #1, pin A (Input)
hm2/hm2_7i80.0:     IO Pin 002 (J2-02): Encoder #2, pin B (Input)
hm2/hm2_7i80.0:     IO Pin 003 (J2-15): Encoder #2, pin A (Input)
hm2/hm2_7i80.0:     IO Pin 004 (J2-03): Encoder #1, pin Index (Input)
hm2/hm2_7i80.0:     IO Pin 005 (J2-16): Encoder #2, pin Index (Input)
hm2/hm2_7i80.0:     IO Pin 006 (J2-04): PWMGen #1, pin Out0 (PWM or Up) (Output)
hm2/hm2_7i80.0:     IO Pin 007 (J2-17): PWMGen #2, pin Out0 (PWM or Up) (Output)
hm2/hm2_7i80.0:     IO Pin 008 (J2-05): PWMGen #1, pin Out1 (Dir or Down) (Output)
hm2/hm2_7i80.0:     IO Pin 009 (J2-06): PWMGen #2, pin Out1 (Dir or Down) (Output)
hm2/hm2_7i80.0:     IO Pin 010 (J2-07): PWMGen #1, pin Not-Enable (Output)
hm2/hm2_7i80.0:     IO Pin 011 (J2-08): PWMGen #2, pin Not-Enable (Output)
hm2/hm2_7i80.0:     IO Pin 012 (J2-09): IOPort
hm2/hm2_7i80.0:     IO Pin 013 (J2-10): IOPort
hm2/hm2_7i80.0:     IO Pin 014 (J2-11): IOPort
hm2/hm2_7i80.0:     IO Pin 015 (J2-12): IOPort
hm2/hm2_7i80.0:     IO Pin 016 (J2-13): IOPort
hm2/hm2_7i80.0:     IO Pin 017 (J3-01): Encoder #0, pin B (Input)
hm2/hm2_7i80.0:     IO Pin 018 (J3-14): Encoder #0, pin A (Input)
hm2/hm2_7i80.0:     IO Pin 019 (J3-02): Encoder #3, pin B (Input)
hm2/hm2_7i80.0:     IO Pin 020 (J3-15): Encoder #3, pin A (Input)
hm2/hm2_7i80.0:     IO Pin 021 (J3-03): Encoder #0, pin Index (Input)
hm2/hm2_7i80.0:     IO Pin 022 (J3-16): Encoder #3, pin Index (Input)
hm2/hm2_7i80.0:     IO Pin 023 (J3-04): PWMGen #0, pin Out0 (PWM or Up) (Output)
hm2/hm2_7i80.0:     IO Pin 024 (J3-17): IOPort
hm2/hm2_7i80.0:     IO Pin 025 (J3-05): PWMGen #0, pin Out1 (Dir or Down) (Output)
hm2/hm2_7i80.0:     IO Pin 026 (J3-06): IOPort
hm2/hm2_7i80.0:     IO Pin 027 (J3-07): PWMGen #0, pin Not-Enable (Output)
hm2/hm2_7i80.0:     IO Pin 028 (J3-08): IOPort
hm2/hm2_7i80.0:     IO Pin 029 (J3-09): IOPort
hm2/hm2_7i80.0:     IO Pin 030 (J3-10): IOPort
hm2/hm2_7i80.0:     IO Pin 031 (J3-11): IOPort
hm2/hm2_7i80.0:     IO Pin 032 (J3-12): IOPort
hm2/hm2_7i80.0:     IO Pin 033 (J3-13): IOPort
hm2/hm2_7i80.0:     IO Pin 034 (J4-01): IOPort
hm2/hm2_7i80.0:     IO Pin 035 (J4-14): IOPort
hm2/hm2_7i80.0:     IO Pin 036 (J4-02): Encoder #4, pin B (Input)
hm2/hm2_7i80.0:     IO Pin 037 (J4-15): Encoder #4, pin A (Input)
hm2/hm2_7i80.0:     IO Pin 038 (J4-03): IOPort
hm2/hm2_7i80.0:     IO Pin 039 (J4-16): Encoder #4, pin Index (Input)
hm2/hm2_7i80.0:     IO Pin 040 (J4-04): IOPort
hm2/hm2_7i80.0:     IO Pin 041 (J4-17): IOPort
hm2/hm2_7i80.0:     IO Pin 042 (J4-05): IOPort
hm2/hm2_7i80.0:     IO Pin 043 (J4-06): IOPort
hm2/hm2_7i80.0:     IO Pin 044 (J4-07): IOPort
hm2/hm2_7i80.0:     IO Pin 045 (J4-08): IOPort
hm2/hm2_7i80.0:     IO Pin 046 (J4-09): IOPort
hm2/hm2_7i80.0:     IO Pin 047 (J4-10): IOPort
hm2/hm2_7i80.0:     IO Pin 048 (J4-11): IOPort
hm2/hm2_7i80.0:     IO Pin 049 (J4-12): IOPort
hm2/hm2_7i80.0:     IO Pin 050 (J4-13): IOPort
hm2/hm2_7i80.0:     IO Pin 051 (J5-01): IOPort
hm2/hm2_7i80.0:     IO Pin 052 (J5-14): IOPort
hm2/hm2_7i80.0:     IO Pin 053 (J5-02): IOPort
hm2/hm2_7i80.0:     IO Pin 054 (J5-15): IOPort
hm2/hm2_7i80.0:     IO Pin 055 (J5-03): IOPort
hm2/hm2_7i80.0:     IO Pin 056 (J5-16): IOPort
hm2/hm2_7i80.0:     IO Pin 057 (J5-04): IOPort
hm2/hm2_7i80.0:     IO Pin 058 (J5-17): IOPort
hm2/hm2_7i80.0:     IO Pin 059 (J5-05): IOPort
hm2/hm2_7i80.0:     IO Pin 060 (J5-06): IOPort
hm2/hm2_7i80.0:     IO Pin 061 (J5-07): IOPort
hm2/hm2_7i80.0:     IO Pin 062 (J5-08): IOPort
hm2/hm2_7i80.0:     IO Pin 063 (J5-09): IOPort
hm2/hm2_7i80.0:     IO Pin 064 (J5-10): IOPort
hm2/hm2_7i80.0:     IO Pin 065 (J5-11): IOPort
hm2/hm2_7i80.0:     IO Pin 066 (J5-12): IOPort
hm2/hm2_7i80.0:     IO Pin 067 (J5-13): IOPort
hm2/hm2_7i80.0: registered
Found file(REL): ./custom.hal
[QTvcp][INFO]  Logging to "/home/mauro/qtvcp.log" (logger.py:100)
[QTvcp.QTVCP.QT_PSTAT][INFO]  Using DEFAULT handler file path: /usr/share/qtvcp/screens/qtplasmac/qtplasmac_handler.py (qt_pstat.py:95)
[QTvcp.QTVCP.QT_PSTAT][INFO]  Using DEFAULT ui file from /usr/share/qtvcp/screens/qtplasmac/qtplasmac.ui (qt_pstat.py:116)
[QTvcp.QTVCP.QT_PSTAT][INFO]  No qss file found (qt_pstat.py:152)
[QTvcp.QTVCP.QT_PSTAT][INFO]  No qrc file found (qt_pstat.py:176)
[QTvcp.QTVCP.QT_PSTAT][INFO]  No resources.py file found, No QRC file to compile one from. (qt_pstat.py:197)
[QTvcp][INFO]  Building A Linuxcnc Main Screen with Python 2 (qtvcp:136)
[QTvcp][INFO]  No handler file specified on command line (qtvcp:154)
[QTvcp][INFO]  No HAL component base name specified on command line using: qtplasmac (qtvcp:185)
[QTvcp.QTVCP.QT_MAKEGUI][INFO]  No resource file to load: None (qt_makegui.py:186)
[QTvcp][INFO]  postgui filename: ['custom_postgui.hal'] (qtvcp:361)
[QTvcp][INFO]  Preference path: /home/mauro/linuxcnc/configs/qtplasma2/qtplasmac.prefs (qtvcp:351)
[QTvcp.QTVCP.QT_MAKEPINS][INFO]  Closing cleanup on: filemanager (qt_makepins.py:86)
Shutting down and cleaning up LinuxCNC...
Running HAL shutdown script
task: 1760 cycles, min=0.000009, max=0.011019, avg=0.009893, 0 latency excursions (> 10x expected cycle time of 0.010000s)
hm2_eth: in hm2_eth_reset
hm2_eth: HostMot2 ethernet driver unloaded
hm2: unloading
Note: Using POSIX realtime
mauro@mauro:~/linuxcnc/configs/qtplasma2$