N00010 ; file name: SPIRAL APPROX 100mm.tap
N00020 ; date and time: Wed Jul 21 2021    15:26:54
N00030 ; postprocessor: plasmacPHILL2.scpost rev: G


N00050 ; begin pre-amble
N00060  G21 (units: metric)
N00070  G40 (cutter compensation: off)
N00080  G90 (distance mode: absolute)
N00090  M52 P1 (adaptive feed: on)
N00100  M65 P2 (enable THC)
N00110  M65 P3 (enable torch)
N00120  M68 E3 Q0 (velocity 100%)
N00130  G64 P0.254 Q0.025 (tracking tolerances: 0.254mm)
N00140  F#<_hal[plasmac.cut-feed-rate]>
N00150 ; end pre-amble


N00170 ; begin material setup
N00180  M190 P1 (plasma finecut 3mm steel material)
N00190  M66 P3 L3 Q2 (wait for valid change)
N00200  F#<_hal[plasmac.cut-feed-rate]>
N00210 ; end material setup


N00230 ; begin operation #1, cutting, 1858.25mm

N00240  G0 X52.042 Y52.753

N00250  M3 $0 S1 (cut start)

N00260  G2 X56.678 Y52.728 I2.319 J0.032
N00270  G2 X47.412 Y53.086 I-4.642 J-0.044
N00280  G2 X61.166 Y51.058 I6.990 J-0.248
N00290  G2 X42.881 Y54.402 I-9.163 J1.558
N00300  G2 X65.828 Y50.854 I11.520 J-1.470
N00310  G2 X38.196 Y54.236 I-13.816 J1.691
N00320  G2 X70.537 Y51.329 I16.189 J-1.241
N00330  G2 X38.331 Y40.064 I-18.475 J1.149
N00340  G2 X35.122 Y60.976 I14.989 J13.002
N00350  G2 X74.964 Y56.120 I19.254 J-7.894
N00360  G2 X46.193 Y29.956 I-22.991 J-3.619
N00370  G2 X29.288 Y57.516 I6.387 J22.883
N00380  G2 X69.067 Y73.921 I25.068 J-4.354
N00390  G2 X78.722 Y44.719 I-15.768 J-21.411
N00400  G2 X32.927 Y32.217 I-26.662 J7.539
N00410  G2 X26.075 Y63.350 I20.474 J20.827
N00420  G2 X77.224 Y72.702 I28.266 J-10.042
N00430  G2 X81.770 Y39.497 I-24.484 J-20.265
N00440  G2 X22.417 Y39.260 I-29.728 J12.684
N00450  G2 X35.330 Y82.327 I32.146 J13.831
N00460  G2 X87.062 Y64.798 I19.032 J-28.934
N00470  G2 X61.987 Y16.439 I-35.285 J-12.384
N00480  G2 X15.894 Y44.255 I-9.843 J35.788
N00490  G2 X47.295 Y92.150 I38.799 J8.803
N00500  G2 X92.932 Y61.019 I6.910 J-38.887
N00510  G2 X60.277 Y11.184 I-41.277 J-8.568
N00520  G2 X11.566 Y42.388 I-8.088 J40.996
N00530  G2 X43.882 Y96.228 I43.218 J10.678
N00540  G2 X96.323 Y66.402 I10.354 J-42.810
N00550  G2 X65.308 Y7.605 I-44.732 J-13.983
N00560  G2 X8.605 Y36.233 I-13.168 J44.387
N00570  G2 X37.519 Y99.173 I46.246 J16.866
N00580  G2 X98.859 Y72.851 I16.775 J-45.541
N00590  G2 X78.892 Y8.690 I-47.375 J-20.444
N00600  G2 X7.334 Y27.792 I-26.846 J43.013
N00610  G2 X1.037 Y52.450 I46.017 J24.884
N00620  G1 X1.036 Y52.753

N00630  M5 $0(cut stop)

N00640 ; end operation #1, cutting


N00660 ; begin post-amble
N00670  G40 (cutter compensation: off)
N00680  G90 (distance mode: absolute)
N00690  M65 P2 (enable THC)
N00700  M65 P3 (enable torch)
N00710  M68 E3 Q0 (velocity 100%)
N00720  M5 $-1 (backup stop)
N00730 ; end post-amble


N00750 ;begin statistics
N00760 ;Pierces = 1
N00770 ;Cuts = 1,    Length = 1858.25mm
N00780 ;end statistics


N00800  M30 (end program)