[Tool0]
Type=PlasmaTool
Name=45 amp 26 gauge steel
Comment=
Tool\ number=1
Kerf\ width=0.889
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=1.524
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=8890
[Tool0/Custom]
Preset\ volts=128
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool1]
Type=PlasmaTool
Name=45 amp 22 gauge steel
Comment=
Tool\ number=2
Kerf\ width=0.889
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=1.524
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=8890
[Tool1/Custom]
Preset\ volts=128
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool2]
Type=PlasmaTool
Name=45 amp 18 gauge steel
Comment=
Tool\ number=3
Kerf\ width=1.3716
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=8255
[Tool2/Custom]
Preset\ volts=129
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool3]
Type=PlasmaTool
Name=45 amp 16 gauge steel
Comment=
Tool\ number=4
Kerf\ width=1.397
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=6985
[Tool3/Custom]
Preset\ volts=130
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool4]
Type=PlasmaTool
Name=45 amp 14 gauge steel
Comment=
Tool\ number=5
Kerf\ width=1.397
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=5588
[Tool4/Custom]
Preset\ volts=130
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool5]
Type=PlasmaTool
Name=45 amp 12 gauge steel
Comment=
Tool\ number=6
Kerf\ width=1.524
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=4572
[Tool5/Custom]
Preset\ volts=133
DTHC\ delay\ -sec=1.5
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool6]
Type=PlasmaTool
Name=45 amp 10 gauge steel
Comment=
Tool\ number=7
Kerf\ width=1.016
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=2540
[Tool6/Custom]
Preset\ volts=134
DTHC\ delay\ -sec=1.5
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool7]
Type=PlasmaTool
Name=45 amp 3/16 steel
Comment=
Tool\ number=8
Kerf\ width=1.651
Plunge\ rate=3810
Pierce\ delay=0.5
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=1600.1999999999998
[Tool7/Custom]
Preset\ volts=135
DTHC\ delay\ -sec=2
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool8]
Type=PlasmaTool
Name=45 amp 1/4 steel
Comment=
Tool\ number=9
Kerf\ width=1.6764
Plunge\ rate=3810
Pierce\ delay=0.6
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=1143
[Tool8/Custom]
Preset\ volts=137
DTHC\ delay\ -sec=2
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool9]
Type=PlasmaTool
Name=45 amp 1/32 aluminum
Comment=
Tool\ number=10
Kerf\ width=1.4986
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=8255
[Tool9/Custom]
Preset\ volts=136
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool10]
Type=PlasmaTool
Name=45 amp 1/16 aluminum
Comment=
Tool\ number=11
Kerf\ width=1.5494
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=8255
[Tool10/Custom]
Preset\ volts=136
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool11]
Type=PlasmaTool
Name=45 amp 3/32 aluminum
Comment=
Tool\ number=12
Kerf\ width=1.6256
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=5080
[Tool11/Custom]
Preset\ volts=136
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool12]
Type=PlasmaTool
Name=45 amp 1/8 aluminum
Comment=
Tool\ number=13
Kerf\ width=1.016
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=2540
[Tool12/Custom]
Preset\ volts=142
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool13]
Type=PlasmaTool
Name=45 amp 1/4 aluminum
Comment=
Tool\ number=14
Kerf\ width=1.524
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=1371.5999999999999
[Tool13/Custom]
Preset\ volts=142
DTHC\ delay\ -sec=2
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool14]
Type=PlasmaTool
Name=65 amp 16 gauge steel
Comment=
Tool\ number=15
Kerf\ width=1.524
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=6350
[Tool14/Custom]
Preset\ volts=123
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=65
NO\ DTHC\ -\ 0=1
[Tool15]
Type=PlasmaTool
Name=65 amp 10 gauge steel
Comment=
Tool\ number=16
Kerf\ width=1.651
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=4826
[Tool15/Custom]
Preset\ volts=125
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=65
NO\ DTHC\ -\ 0=1
[Tool16]
Type=PlasmaTool
Name=65 amp 3/16 steel
Comment=
Tool\ number=17
Kerf\ width=1.7272
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=3378.1999999999998
[Tool16/Custom]
Preset\ volts=126
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=65
NO\ DTHC\ -\ 0=1
[Tool17]
Type=PlasmaTool
Name=65 amp 1/4 steel
Comment=
Tool\ number=18
Kerf\ width=1.778
Plunge\ rate=3810
Pierce\ delay=0.3
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=2286
[Tool17/Custom]
Preset\ volts=127
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=65
NO\ DTHC\ -\ 0=1
[Tool18]
Type=PlasmaTool
Name=65 amp 3/8 steel
Comment=
Tool\ number=19
Kerf\ width=1.9304
Plunge\ rate=3810
Pierce\ delay=0.7
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=1016
[Tool18/Custom]
Preset\ volts=130
DTHC\ delay\ -sec=2
Tip\ Size\ -Amps=65
NO\ DTHC\ -\ 0=1
[Tool19]
Type=PlasmaTool
Name=65 amp 1/2 steel
Comment=
Tool\ number=20
Kerf\ width=2.2352
Plunge\ rate=3810
Pierce\ delay=1.3
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=4.571999999999999
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=762
[Tool19/Custom]
Preset\ volts=135
DTHC\ delay\ -sec=3
Tip\ Size\ -Amps=65
NO\ DTHC\ -\ 0=1
[Tool20]
Type=PlasmaTool
Name=65 amp 5/8 steel
Comment=
Tool\ number=21
Kerf\ width=2.286
Plunge\ rate=3810
Pierce\ delay=2
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=6.095999999999999
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=508
[Tool20/Custom]
Preset\ volts=138
DTHC\ delay\ -sec=3
Tip\ Size\ -Amps=65
NO\ DTHC\ -\ 0=1
[Tool21]
Type=PlasmaTool
Name=65 amp 1/16 aluminum
Comment=
Tool\ number=22
Kerf\ width=1.8542
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=8890
[Tool21/Custom]
Preset\ volts=121
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=65
NO\ DTHC\ -\ 0=1
[Tool22]
Type=PlasmaTool
Name=65 amp 1/8 aluminum
Comment=
Tool\ number=23
Kerf\ width=1.8796
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=6858
[Tool22/Custom]
Preset\ volts=124
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=65
NO\ DTHC\ -\ 0=1
[Tool23]
Type=PlasmaTool
Name=65 amp 1/4 aluminum
Comment=
Tool\ number=24
Kerf\ width=1.905
Plunge\ rate=3810
Pierce\ delay=0.5
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=2286
[Tool23/Custom]
Preset\ volts=131
DTHC\ delay\ -sec=2
Tip\ Size\ -Amps=65
NO\ DTHC\ -\ 0=1
[Tool24]
Type=PlasmaTool
Name=65 amp 3/8 aluminum
Comment=
Tool\ number=25
Kerf\ width=2.1082
Plunge\ rate=3810
Pierce\ delay=0.7
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=1270
[Tool24/Custom]
Preset\ volts=135
DTHC\ delay\ -sec=2
Tip\ Size\ -Amps=65
NO\ DTHC\ -\ 0=1
[Tool25]
Type=PlasmaTool
Name=65 amp 1/2 aluminum
Comment=
Tool\ number=26
Kerf\ width=2.3114
Plunge\ rate=3810
Pierce\ delay=1.2
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=4.571999999999999
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=838.19999999999993
[Tool25/Custom]
Preset\ volts=139
DTHC\ delay\ -sec=3
Tip\ Size\ -Amps=65
NO\ DTHC\ -\ 0=1
[Tool26]
Type=PlasmaTool
Name=85 amp 10 gauge steel
Comment=
Tool\ number=27
Kerf\ width=1.7272
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=6350
[Tool26/Custom]
Preset\ volts=122
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=85
NO\ DTHC\ -\ 0=1
[Tool27]
Type=PlasmaTool
Name=85 amp 3/16 steel
Comment=
Tool\ number=28
Kerf\ width=1.8034
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=4699
[Tool27/Custom]
Preset\ volts=123
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=85
NO\ DTHC\ -\ 0=1
[Tool28]
Type=PlasmaTool
Name=85 amp 1/4 steel
Comment=
Tool\ number=29
Kerf\ width=1.8542
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=3048
[Tool28/Custom]
Preset\ volts=123
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=85
NO\ DTHC\ -\ 0=1
[Tool29]
Type=PlasmaTool
Name=85 amp 3/8 steel
Comment=
Tool\ number=30
Kerf\ width=1.9812
Plunge\ rate=3810
Pierce\ delay=0.7
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=1778
[Tool29/Custom]
Preset\ volts=126
DTHC\ delay\ -sec=1.5
Tip\ Size\ -Amps=85
NO\ DTHC\ -\ 0=1
[Tool30]
Type=PlasmaTool
Name=85 amp 1/2 steel
Comment=
Tool\ number=31
Kerf\ width=2.286
Plunge\ rate=3810
Pierce\ delay=0.7
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=4.571999999999999
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=1143
[Tool30/Custom]
Preset\ volts=131
DTHC\ delay\ -sec=2
Tip\ Size\ -Amps=85
NO\ DTHC\ -\ 0=1
[Tool31]
Type=PlasmaTool
Name=85 amp 5/8 steel
Comment=
Tool\ number=32
Kerf\ width=2.413
Plunge\ rate=3810
Pierce\ delay=1
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=4.571999999999999
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=889
[Tool31/Custom]
Preset\ volts=134
DTHC\ delay\ -sec=3
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool32]
Type=PlasmaTool
Name=85 amp 3/4 steel
Comment=
Tool\ number=33
Kerf\ width=2.54
Plunge\ rate=3810
Pierce\ delay=1.5
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=6.095999999999999
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=609.59999999999991
[Tool32/Custom]
Preset\ volts=136
DTHC\ delay\ -sec=3
Tip\ Size\ -Amps=85
NO\ DTHC\ -\ 0=1
[Tool33]
Type=PlasmaTool
Name=85 amp 7/8 steel
Comment=
Tool\ number=34
Kerf\ width=2.54
Plunge\ rate=3810
Pierce\ delay=2
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=6.095999999999999
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=482.59999999999997
[Tool33/Custom]
Preset\ volts=139
DTHC\ delay\ -sec=3
Tip\ Size\ -Amps=85
NO\ DTHC\ -\ 0=1
[Tool34]
Type=PlasmaTool
Name=85 amp 1.0 steel
Comment=
Tool\ number=35
Kerf\ width=3.048
Plunge\ rate=3810
Pierce\ delay=2.25
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=6.095999999999999
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=330.19999999999999
[Tool34/Custom]
Preset\ volts=142
DTHC\ delay\ -sec=4
Tip\ Size\ -Amps=85
NO\ DTHC\ -\ 0=1
[Tool35]
Type=PlasmaTool
Name=105 amp 1/4 steel
Comment=
Tool\ number=36
Kerf\ width=2.1082
Plunge\ rate=3810
Pierce\ delay=0.5
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=6.35
Cut\ height=3.175
Pierce\ type=0
Feed\ rate=3962.3999999999996
[Tool35/Custom]
Preset\ volts=144
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=105
NO\ DTHC\ -\ 0=1
[Tool36]
Type=PlasmaTool
Name=105 amp 3/8 steel
Comment=
Tool\ number=37
Kerf\ width=2.2352
Plunge\ rate=3810
Pierce\ delay=0.75
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=6.35
Cut\ height=3.175
Pierce\ type=0
Feed\ rate=2387.5999999999999
[Tool36/Custom]
Preset\ volts=145
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=105
NO\ DTHC\ -\ 0=1
[Tool37]
Type=PlasmaTool
Name=105 amp 1/2 steel
Comment=
Tool\ number=38
Kerf\ width=2.2606
Plunge\ rate=3810
Pierce\ delay=0.75
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=6.35
Cut\ height=3.175
Pierce\ type=0
Feed\ rate=1574.8
[Tool37/Custom]
Preset\ volts=146
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=105
NO\ DTHC\ -\ 0=1
[Tool38]
Type=PlasmaTool
Name=105 amp 5/8 steel
Comment=
Tool\ number=39
Kerf\ width=2.54
Plunge\ rate=3810
Pierce\ delay=1
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=6.35
Cut\ height=3.175
Pierce\ type=0
Feed\ rate=1066.8
[Tool38/Custom]
Preset\ volts=149
DTHC\ delay\ -sec=4
Tip\ Size\ -Amps=105
NO\ DTHC\ -\ 0=1
[Tool39]
Type=PlasmaTool
Name=Finecut 16ga steel
Comment=
Tool\ number=40
Kerf\ width=1.1684
Plunge\ rate=3810
Pierce\ delay=0.1
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=2.286
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=6350
[Tool39/Custom]
Preset\ volts=76
DTHC\ delay\ -sec=0.75
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool40]
Type=PlasmaTool
Name=Finecut 14ga steel
Comment=
Tool\ number=41
Kerf\ width=1.2446
Plunge\ rate=3810
Pierce\ delay=0.1
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=22.859999999999999
Cut\ height=1.778
Pierce\ type=0
Feed\ rate=5588
[Tool40/Custom]
Preset\ volts=74
DTHC\ delay\ -sec=0.75
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool41]
Type=PlasmaTool
Name=Finecut 12ga steel
Comment=
Tool\ number=42
Kerf\ width=1.3208
Plunge\ rate=3810
Pierce\ delay=0.2
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=2.286
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=3048
[Tool41/Custom]
Preset\ volts=78
DTHC\ delay\ -sec=0.75
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool42]
Type=PlasmaTool
Name=Finecut 11ga steel
Comment=
Tool\ number=43
Kerf\ width=1.3208
Plunge\ rate=3810
Pierce\ delay=0.2
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=2.286
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=2717.7999999999997
[Tool42/Custom]
Preset\ volts=76
DTHC\ delay\ -sec=0.07
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool43]
Type=PlasmaTool
Name=Finecut 10ga steel
Comment=
Tool\ number=44
Kerf\ width=1.3208
Plunge\ rate=3810
Pierce\ delay=0.2
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=22.859999999999999
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=2413
[Tool43/Custom]
Preset\ volts=76
DTHC\ delay\ -sec=0.75
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool44]
Type=PlasmaTool
Name=105 amp 1 1/2 steel edge start
Comment=
Tool\ number=45
Kerf\ width=5.08
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=0
Cut\ height=3.175
Pierce\ type=0
Feed\ rate=228.59999999999999
[Tool44/Custom]
Preset\ volts=49
DTHC\ delay\ -sec=0
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool45]
Type=PlasmaTool
Name=105 amp 1/4 stainless
Comment=
Tool\ number=46
Kerf\ width=1.9304
Plunge\ rate=3810
Pierce\ delay=0.5
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=6.35
Cut\ height=3.175
Pierce\ type=0
Feed\ rate=4699
[Tool45/Custom]
Preset\ volts=139
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=105
NO\ DTHC\ -\ 0=1
[Tool46]
Type=PlasmaTool
Name=105 amp 3/8 stainless
Comment=
Tool\ number=47
Kerf\ width=2.2606
Plunge\ rate=3810
Pierce\ delay=0.05
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=6.35
Cut\ height=3.175
Pierce\ type=0
Feed\ rate=2387.5999999999999
[Tool46/Custom]
Preset\ volts=143
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=105
NO\ DTHC\ -\ 0=1
[Tool47]
Type=PlasmaTool
Name=105 amp 1/2 stainless
Comment=
Tool\ number=48
Kerf\ width=2.3114
Plunge\ rate=3810
Pierce\ delay=1
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=6.35
Cut\ height=3.175
Pierce\ type=0
Feed\ rate=1397
[Tool47/Custom]
Preset\ volts=148
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=105
NO\ DTHC\ -\ 0=1
[Tool48]
Type=PlasmaTool
Name=105 amp 5/8 stainless
Comment=
Tool\ number=49
Kerf\ width=2.3368
Plunge\ rate=3810
Pierce\ delay=1.25
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=6.35
Cut\ height=3.175
Pierce\ type=0
Feed\ rate=965.19999999999993
[Tool48/Custom]
Preset\ volts=149
DTHC\ delay\ -sec=1.2
Tip\ Size\ -Amps=105
NO\ DTHC\ -\ 0=1
[Tool49]
Type=PlasmaTool
Name=105 amp 3/4 stainless
Comment=
Tool\ number=50
Kerf\ width=2.5146
Plunge\ rate=3810
Pierce\ delay=1.5
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=7.874
Cut\ height=3.175
Pierce\ type=0
Feed\ rate=711.19999999999993
[Tool49/Custom]
Preset\ volts=153
DTHC\ delay\ -sec=4
Tip\ Size\ -Amps=105
NO\ DTHC\ -\ 0=1
[Tool50]
Type=PlasmaTool
Name=105 amp 7/8 stainless edge start
Comment=
Tool\ number=51
Kerf\ width=2.413
Plunge\ rate=3810
Pierce\ delay=1.5
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=0
Cut\ height=3.175
Pierce\ type=0
Feed\ rate=558.79999999999995
[Tool50/Custom]
Preset\ volts=156
DTHC\ delay\ -sec=4
Tip\ Size\ -Amps=105
NO\ DTHC\ -\ 0=1
[Tool51]
Type=PlasmaTool
Name=105 amp 1.0 stainless edge start
Comment=
Tool\ number=52
Kerf\ width=2.8702
Plunge\ rate=3810
Pierce\ delay=2
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=0
Cut\ height=3.175
Pierce\ type=0
Feed\ rate=431.79999999999995
[Tool51/Custom]
Preset\ volts=158
DTHC\ delay\ -sec=4
Tip\ Size\ -Amps=105
NO\ DTHC\ -\ 0=1
[Tool52]
Type=PlasmaTool
Name=105 amp 1 1/8 stainless edge start
Comment=
Tool\ number=53
Kerf\ width=3.2512
Plunge\ rate=3810
Pierce\ delay=2
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=0
Cut\ height=3.175
Pierce\ type=0
Feed\ rate=355.59999999999997
[Tool52/Custom]
Preset\ volts=162
DTHC\ delay\ -sec=4
Tip\ Size\ -Amps=105
NO\ DTHC\ -\ 0=1
[Tool53]
Type=PlasmaTool
Name=105 amp 1 1/4 stainless edge start
Comment=
Tool\ number=54
Kerf\ width=3.6576
Plunge\ rate=3810
Pierce\ delay=2.1
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=0
Cut\ height=3.175
Pierce\ type=0
Feed\ rate=279.39999999999998
[Tool53/Custom]
Preset\ volts=166
DTHC\ delay\ -sec=4
Tip\ Size\ -Amps=105
NO\ DTHC\ -\ 0=1
[Tool54]
Type=PlasmaTool
Name=105 amp 1/4 aluminum
Comment=
Tool\ number=55
Kerf\ width=2.3114
Plunge\ rate=3810
Pierce\ delay=0.5
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=6.35
Cut\ height=3.175
Pierce\ type=0
Feed\ rate=5664.1999999999998
[Tool54/Custom]
Preset\ volts=146
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=105
NO\ DTHC\ -\ 0=1
[Tool55]
Type=PlasmaTool
Name=105 amp 3/8 aluminum
Comment=
Tool\ number=56
Kerf\ width=2.3368
Plunge\ rate=3810
Pierce\ delay=0.75
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=6.35
Cut\ height=3.175
Pierce\ type=0
Feed\ rate=2794
[Tool55/Custom]
Preset\ volts=151
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=105
NO\ DTHC\ -\ 0=1
[Tool56]
Type=PlasmaTool
Name=105 amp 1/2 aluminum
Comment=
Tool\ number=57
Kerf\ width=2.5908
Plunge\ rate=3810
Pierce\ delay=1
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=6.35
Cut\ height=3.175
Pierce\ type=0
Feed\ rate=1803.3999999999999
[Tool56/Custom]
Preset\ volts=156
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=105
NO\ DTHC\ -\ 0=1
[Tool57]
Type=PlasmaTool
Name=105 amp 5/8 aluminum
Comment=
Tool\ number=58
Kerf\ width=2.7178
Plunge\ rate=3810
Pierce\ delay=1
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=6.35
Cut\ height=3.175
Pierce\ type=0
Feed\ rate=1295.3999999999999
[Tool57/Custom]
Preset\ volts=157
DTHC\ delay\ -sec=1.2
Tip\ Size\ -Amps=105
NO\ DTHC\ -\ 0=1
[Tool58]
Type=PlasmaTool
Name=105 amp 3/4 aluminum
Comment=
Tool\ number=59
Kerf\ width=2.8194
Plunge\ rate=3810
Pierce\ delay=1.25
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=6.35
Cut\ height=3.175
Pierce\ type=0
Feed\ rate=1092.2
[Tool58/Custom]
Preset\ volts=162
DTHC\ delay\ -sec=4
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool59]
Type=PlasmaTool
Name=105 amp 7/8 aluminum edge start
Comment=
Tool\ number=60
Kerf\ width=3.1496
Plunge\ rate=3810
Pierce\ delay=1.5
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=0
Cut\ height=3.175
Pierce\ type=0
Feed\ rate=863.59999999999991
[Tool59/Custom]
Preset\ volts=164
DTHC\ delay\ -sec=4
Tip\ Size\ -Amps=105
NO\ DTHC\ -\ 0=1
[Tool60]
Type=PlasmaTool
Name=105 amp 1.0 aluminum edge start
Comment=
Tool\ number=61
Kerf\ width=3.5052
Plunge\ rate=3810
Pierce\ delay=1.75
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=0
Cut\ height=3.175
Pierce\ type=0
Feed\ rate=635
[Tool60/Custom]
Preset\ volts=166
DTHC\ delay\ -sec=4
Tip\ Size\ -Amps=105
NO\ DTHC\ -\ 0=1
[Tool61]
Type=PlasmaTool
Name=105 amp 1 1/8 aluminum edge start
Comment=
Tool\ number=62
Kerf\ width=4.191
Plunge\ rate=3810
Pierce\ delay=2
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=0
Cut\ height=3.175
Pierce\ type=0
Feed\ rate=508
[Tool61/Custom]
Preset\ volts=171
DTHC\ delay\ -sec=3
Tip\ Size\ -Amps=105
NO\ DTHC\ -\ 0=1
[Tool62]
Type=PlasmaTool
Name=105 amp 1 1/4 aluminum edge start
Comment=
Tool\ number=63
Kerf\ width=4.8768
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=0
Cut\ height=3.175
Pierce\ type=0
Feed\ rate=381
[Tool62/Custom]
Preset\ volts=175
DTHC\ delay\ -sec=3
Tip\ Size\ -Amps=105
NO\ DTHC\ -\ 0=1
[Tool63]
Type=PlasmaTool
Name=85 amp 10g stainless steel
Comment=
Tool\ number=64
Kerf\ width=1.7272
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=6350
[Tool63/Custom]
Preset\ volts=122
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=85
NO\ DTHC\ -\ 0=1
[Tool64]
Type=PlasmaTool
Name=85 amp 3/16" stainless steel
Comment=
Tool\ number=65
Kerf\ width=1.8034
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=5080
[Tool64/Custom]
Preset\ volts=122
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=85
NO\ DTHC\ -\ 0=1
[Tool65]
Type=PlasmaTool
Name=85 amp 1/4" stainless steel
Comment=
Tool\ number=66
Kerf\ width=1.8542
Plunge\ rate=3810
Pierce\ delay=0.5
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=3302
[Tool65/Custom]
Preset\ volts=122
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=85
NO\ DTHC\ -\ 0=1
[Tool66]
Type=PlasmaTool
Name=85 amp 3/8" stainless steel
Comment=
Tool\ number=67
Kerf\ width=1.9812
Plunge\ rate=3810
Pierce\ delay=0.5
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=1651
[Tool66/Custom]
Preset\ volts=126
DTHC\ delay\ -sec=2
Tip\ Size\ -Amps=85
NO\ DTHC\ -\ 0=1
[Tool67]
Type=PlasmaTool
Name=85 amp 1/2" stainless steel
Comment=
Tool\ number=68
Kerf\ width=2.286
Plunge\ rate=3810
Pierce\ delay=1
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=4.571999999999999
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=914.39999999999998
[Tool67/Custom]
Preset\ volts=132
DTHC\ delay\ -sec=2
Tip\ Size\ -Amps=85
NO\ DTHC\ -\ 0=1
[Tool68]
Type=PlasmaTool
Name=85 amp 5/8" stainless steel
Comment=
Tool\ number=69
Kerf\ width=2.413
Plunge\ rate=3810
Pierce\ delay=2
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=4.571999999999999
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=711.19999999999993
[Tool68/Custom]
Preset\ volts=135
DTHC\ delay\ -sec=3
Tip\ Size\ -Amps=85
NO\ DTHC\ -\ 0=1
[Tool69]
Type=PlasmaTool
Name=65 amp 16g stainless steel
Comment=
Tool\ number=70
Kerf\ width=1.524
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=8255
[Tool69/Custom]
Preset\ volts=124
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=65
NO\ DTHC\ -\ 0=1
[Tool70]
Type=PlasmaTool
Name=65 amp 10g stainless steel
Comment=
Tool\ number=71
Kerf\ width=1.651
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=5715
[Tool70/Custom]
Preset\ volts=125
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=65
NO\ DTHC\ -\ 0=1
[Tool71]
Type=PlasmaTool
Name=65 amp 3/16" stainless steel
Comment=
Tool\ number=72
Kerf\ width=1.7272
Plunge\ rate=3810
Pierce\ delay=0.5
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=3937
[Tool71/Custom]
Preset\ volts=126
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=65
NO\ DTHC\ -\ 0=1
[Tool72]
Type=PlasmaTool
Name=65 amp 1/4" stainless steel
Comment=
Tool\ number=73
Kerf\ width=1.778
Plunge\ rate=3810
Pierce\ delay=0.5
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=2032
[Tool72/Custom]
Preset\ volts=126
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=65
NO\ DTHC\ -\ 0=1
[Tool73]
Type=PlasmaTool
Name=65 amp 3/8" stainless steel
Comment=
Tool\ number=74
Kerf\ width=1.9304
Plunge\ rate=3810
Pierce\ delay=1
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=1016
[Tool73/Custom]
Preset\ volts=131
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=65
NO\ DTHC\ -\ 0=1
[Tool74]
Type=PlasmaTool
Name=65 amp 1/2" stainless steel
Comment=
Tool\ number=75
Kerf\ width=2.2352
Plunge\ rate=3810
Pierce\ delay=1.5
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=4.571999999999999
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=660.39999999999998
[Tool74/Custom]
Preset\ volts=136
DTHC\ delay\ -sec=2
Tip\ Size\ -Amps=65
NO\ DTHC\ -\ 0=1
[Tool75]
Type=PlasmaTool
Name=65 amp 5/8" stainless steel
Comment=
Tool\ number=76
Kerf\ width=2.286
Plunge\ rate=3810
Pierce\ delay=1.75
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=4.571999999999999
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=660.39999999999998
[Tool75/Custom]
Preset\ volts=139
DTHC\ delay\ -sec=3
Tip\ Size\ -Amps=65
NO\ DTHC\ -\ 0=1
[Tool76]
Type=PlasmaTool
Name=45 amp 26g stainless steel
Comment=
Tool\ number=77
Kerf\ width=0.889
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=1.524
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=8890
[Tool76/Custom]
Preset\ volts=130
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool77]
Type=PlasmaTool
Name=45 amp 22g stainless steel
Comment=
Tool\ number=78
Kerf\ width=0.889
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=1.524
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=8890
[Tool77/Custom]
Preset\ volts=130
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool78]
Type=PlasmaTool
Name=45 amp 18g stainless steel
Comment=
Tool\ number=79
Kerf\ width=1.3716
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=1.524
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=8890
[Tool78/Custom]
Preset\ volts=130
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool79]
Type=PlasmaTool
Name=45 amp 16g stainless steel
Comment=
Tool\ number=80
Kerf\ width=1.3716
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=2.032
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=8890
[Tool79/Custom]
Preset\ volts=130
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool80]
Type=PlasmaTool
Name=45 amp 14g stainless steel
Comment=
Tool\ number=81
Kerf\ width=1.397
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=6350
[Tool80/Custom]
Preset\ volts=132
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool81]
Type=PlasmaTool
Name=45 amp 12g stainless steel
Comment=
Tool\ number=82
Kerf\ width=1.4732
Plunge\ rate=3810
Pierce\ delay=0.5
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=3556
[Tool81/Custom]
Preset\ volts=132
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool82]
Type=PlasmaTool
Name=45 amp 10g  stainless steel
Comment=
Tool\ number=83
Kerf\ width=1.5494
Plunge\ rate=3810
Pierce\ delay=0.7
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=2540
[Tool82/Custom]
Preset\ volts=133
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool83]
Type=PlasmaTool
Name=45 amp 3/16" stainless steel
Comment=
Tool\ number=84
Kerf\ width=1.651
Plunge\ rate=3810
Pierce\ delay=0.7
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=2540
[Tool83/Custom]
Preset\ volts=135
DTHC\ delay\ -sec=1.5
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool84]
Type=PlasmaTool
Name=45 amp 1/4" stainless steel
Comment=
Tool\ number=85
Kerf\ width=1.6764
Plunge\ rate=3810
Pierce\ delay=1
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=762
[Tool84/Custom]
Preset\ volts=141
DTHC\ delay\ -sec=2
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool85]
Type=PlasmaTool
Name=finecut low speed 26g steel
Comment=
Tool\ number=86
Kerf\ width=0.5842
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=3810
[Tool85/Custom]
Preset\ volts=70
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool86]
Type=PlasmaTool
Name=finecut low speed 24 g steel
Comment=
Tool\ number=87
Kerf\ width=0.6604
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=3810
[Tool86/Custom]
Preset\ volts=68
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool87]
Type=PlasmaTool
Name=finecut low speed 22g steel
Comment=
Tool\ number=88
Kerf\ width=0.6604
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=3810
[Tool87/Custom]
Preset\ volts=70
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool88]
Type=PlasmaTool
Name=finecut low speed 18g steel
Comment=
Tool\ number=89
Kerf\ width=0.6604
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=3810
[Tool88/Custom]
Preset\ volts=73
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool89]
Type=PlasmaTool
Name=finecut low speed 16g steel
Comment=
Tool\ number=90
Kerf\ width=0.6604
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=3810
[Tool89/Custom]
Preset\ volts=75
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool90]
Type=PlasmaTool
Name=finecut lowspeed 14g steel
Comment=
Tool\ number=91
Kerf\ width=0.6858
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=3810
[Tool90/Custom]
Preset\ volts=76
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool91]
Type=PlasmaTool
Name=finecut low speed 12g steel
Comment=
Tool\ number=92
Kerf\ width=0.6096
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=3048
[Tool91/Custom]
Preset\ volts=78
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool92]
Type=PlasmaTool
Name=finecut low speed 10g steel
Comment=
Tool\ number=93
Kerf\ width=0.6096
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=2413
[Tool92/Custom]
Preset\ volts=78
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool93]
Type=PlasmaTool
Name=finecut low speed 18g stainless
Comment=
Tool\ number=94
Kerf\ width=0.5842
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=2.032
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=3683
[Tool93/Custom]
Preset\ volts=69
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool94]
Type=PlasmaTool
Name=finecut low speed 16g stainless
Comment=
Tool\ number=95
Kerf\ width=0.5842
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=2.032
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=2921
[Tool94/Custom]
Preset\ volts=69
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool95]
Type=PlasmaTool
Name=finecut low speed 14g stainless
Comment=
Tool\ number=96
Kerf\ width=0.5334
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=2.032
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=2794
[Tool95/Custom]
Preset\ volts=69
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool96]
Type=PlasmaTool
Name=finecut low speed 12g stainless
Comment=
Tool\ number=97
Kerf\ width=0.635
Plunge\ rate=3810
Pierce\ delay=0
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=2.032
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=2794
[Tool96/Custom]
Preset\ volts=80
DTHC\ delay\ -sec=1
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool97]
Type=PlasmaTool
Name=finecut low speed 10g stainless
Comment=
Tool\ number=98
Kerf\ width=0.6858
Plunge\ rate=3810
Pierce\ delay=0.5
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=2.032
Cut\ height=1.524
Pierce\ type=0
Feed\ rate=1905
[Tool97/Custom]
Preset\ volts=80
DTHC\ delay\ -sec=0.5
Tip\ Size\ -Amps=45
NO\ DTHC\ -\ 0=1
[Tool98]
Type=MarkerTool
Name=CenterPunch
Comment=
Tool\ number=99
Diameter=0.0254
Plunge\ rate=3810
Start\ delay=2
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=3.81
Cut\ height=0
Pierce\ type=0
Feed\ rate=6350
[Tool99]
Type=MillTool
Name=Rotary tool
Comment=
Tool\ number=100
Diameter=3.175
Flute\ length=14.224
Spindle\ speed=10000
Spindle\ direction=0
Tool\ length\ offset=0
Depth\ per\ pass=6.35
Point\ angle=2.059488517353309
Plunge\ rate=203.19999999999999
Feed\ rate=889
Ramp\ Angle=0
[Tool100]
Type=MarkerTool
Name=Plate Marker
Comment=
Tool\ number=101
Diameter=0.0254
Plunge\ rate=3810
Start\ delay=0.5
Pause\ at\ end\ of\ cut=0.5
Wiggle\ length=9.999979999999999
Pierce\ height=2.99974
Cut\ height=0
Pierce\ type=0
Feed\ rate=1270
[Tool101]
Type=CodeTool
Name=C1 DTHC-OFF
Comment=
Tool\ number=268435457
Code=S10 (DTHC OFF)
[Tool102]
Type=CodeTool
Name=C2 DTHC=ON
Comment=
Tool\ number=268435458
Code=S20 (DTHCON)
[Tool103]
Type=CodeTool
Name=C3 DTHC-OFF I=90%
Comment=
Tool\ number=268435459
Code=S129 (DTHC-OFRF I=90%)
[Tool104]
Type=CodeTool
Name=C4 DTHC-OFF I=80%
Comment=
Tool\ number=268435460
Code=S18 (DTHC-OFF I=80%)
[Tool105]
Type=CodeTool
Name=C5 DTHC-OFF I=70%
Comment=
Tool\ number=268435461
Code=S17 (DTHC-OFF I=70%)
[Tool106]
Type=CodeTool
Name=C6 DTHC-OFF I=60%
Comment=
Tool\ number=268435462
Code=S16 (DTHC-OFF I=60%)
[Tool107]
Type=CodeTool
Name=C7 DTHC-OFF I=50%
Comment=
Tool\ number=268435463
Code=S15 (DTHC-OFF I=50%)
[Tool108]
Type=CodeTool
Name=C7 DTHC-ON I=90%
Comment=
Tool\ number=268435464
Code=S29 (DTHC-ON I=90%)
[Tool109]
Type=CodeTool
Name=C8 DTHC-ON I=80%
Comment=
Tool\ number=268435465
Code=S28 (DTHC-ON I=80%)
[Tool110]
Type=CodeTool
Name=C9 DTHC-ON I=70%
Comment=
Tool\ number=268435466
Code=S27 (DTHC-ON I=70%)
[Tool111]
Type=CodeTool
Name=Code snippet
Comment=
Tool\ number=268435469
Code=
[pathRules]
GlobalRule=-1
[pathRules/Set0]
name=Holes
[pathRules/Set0/Rule0]
Class=PathRuleOnCircle
Feed\ rate=0.65
Start\ code=268435457
End\ code=268435458
Enabled=1
Smaller\ than=38.099999999999994