bengt@CombiMll ~ $ linuxcnc
LINUXCNC - 2.7.14
Machine configuration directory is '/home/bengt/linuxcnc/configs/GB_3speed'
Machine configuration file is 'GB_3speed.ini'
Starting LinuxCNC...
Found file(REL): ./GB_3speed.hal
Note: Using POSIX realtime
hm2: loading Mesa HostMot2 driver version 0.15
hm2_eth: loading Mesa AnyIO HostMot2 ethernet driver version 0.2
hm2_eth: 10.10.10.10: Hardware address: 00:60:1b:10:41:2b
hm2_eth: discovered 7I76E-16
hm2/hm2_7i76e.0: Smart Serial Firmware Version 43
Board hm2_7i76e.0.7i76.0.0 Hardware Mode 0 = standard
Board hm2_7i76e.0.7i76.0.0 Software Mode 0 = io_spin
Board hm2_7i76e.0.7i76.0.0 Software Mode 1 = io_ana_spin
Board hm2_7i76e.0.7i76.0.0 Software Mode 2 = io_enc_ana_spin_fv
Board hm2_7i76e.0.7i73.0.1 Hardware Mode 0 = nokeyboardnodisplay
Board hm2_7i76e.0.7i73.0.1 Software Mode 0 = inputoutputencoder
Board hm2_7i76e.0.7i73.0.1 Software Mode 1 = inputoutputencoderanalog
Board hm2_7i76e.0.7i73.0.1 Software Mode 2 = inputoutputencoderanalog
Board hm2_7i76e.0.7i73.0.1 Hardware Mode 1 = nokeyboarddisplay
Board hm2_7i76e.0.7i73.0.1 Software Mode 0 = inputoutputencoderdisplay
Board hm2_7i76e.0.7i73.0.1 Software Mode 1 = inputoutputencoderanalogdisplay
Board hm2_7i76e.0.7i73.0.1 Software Mode 2 = inputoutputencoderanalogwidedisplay
Board hm2_7i76e.0.7i73.0.1 Hardware Mode 2 = keyboard4by8nodisplay
Board hm2_7i76e.0.7i73.0.1 Software Mode 0 = inputoutputencoderkeycode4by8
Board hm2_7i76e.0.7i73.0.1 Software Mode 1 = inputoutputencoderanalogkeycode4by8
Board hm2_7i76e.0.7i73.0.1 Software Mode 2 = inputoutputencoderanalogkeycode4by8
Board hm2_7i76e.0.7i73.0.1 Hardware Mode 3 = keyboard4by8display
Board hm2_7i76e.0.7i73.0.1 Software Mode 0 = inputoutputencoderdisplaykeycode4by8
Board hm2_7i76e.0.7i73.0.1 Software Mode 1 = inputoutputencoderanalogdisplaykeycode4by8
Board hm2_7i76e.0.7i73.0.1 Software Mode 2 = inputoutputencoderanalogwidedisplaykeycode4by8
Board hm2_7i76e.0.7i73.0.1 Hardware Mode 4 = keyboard8by8nodisplay
Board hm2_7i76e.0.7i73.0.1 Software Mode 0 = inputoutputencoderkeycode8by8
Board hm2_7i76e.0.7i73.0.1 Software Mode 1 = inputoutputencoderanalogkeycode8by8
Board hm2_7i76e.0.7i73.0.1 Software Mode 2 = inputoutputencoderanalogkeycode8by8
Board hm2_7i76e.0.7i73.0.1 Hardware Mode 5 = keyboard8by8display
Board hm2_7i76e.0.7i73.0.1 Software Mode 0 = inputoutputencoderdisplaykeycode8by8
Board hm2_7i76e.0.7i73.0.1 Software Mode 1 = inputoutputencoderanalogdisplaykeycode8by8
Board hm2_7i76e.0.7i73.0.1 Software Mode 2 = inputoutputencoderanalogwidedisplaykeycode8by8
hm2/hm2_7i76e.0: 51 I/O Pins used:
hm2/hm2_7i76e.0:     IO Pin 000 (P1-01): StepGen #0, pin Direction (Output)
hm2/hm2_7i76e.0:     IO Pin 001 (P1-14): StepGen #0, pin Step (Output)
hm2/hm2_7i76e.0:     IO Pin 002 (P1-02): StepGen #1, pin Direction (Output)
hm2/hm2_7i76e.0:     IO Pin 003 (P1-15): StepGen #1, pin Step (Output)
hm2/hm2_7i76e.0:     IO Pin 004 (P1-03): StepGen #2, pin Direction (Output)
hm2/hm2_7i76e.0:     IO Pin 005 (P1-16): StepGen #2, pin Step (Output)
hm2/hm2_7i76e.0:     IO Pin 006 (P1-04): StepGen #3, pin Direction (Output)
hm2/hm2_7i76e.0:     IO Pin 007 (P1-17): StepGen #3, pin Step (Output)
hm2/hm2_7i76e.0:     IO Pin 008 (P1-05): StepGen #4, pin Direction (Output)
hm2/hm2_7i76e.0:     IO Pin 009 (P1-06): StepGen #4, pin Step (Output)
hm2/hm2_7i76e.0:     IO Pin 010 (P1-07): Smart Serial Interface #0, pin TxData0 (Output)
hm2/hm2_7i76e.0:     IO Pin 011 (P1-08): Smart Serial Interface #0, pin RxData0 (Input)
hm2/hm2_7i76e.0:     IO Pin 012 (P1-09): Smart Serial Interface #0, pin TxData1 (Output)
hm2/hm2_7i76e.0:     IO Pin 013 (P1-10): Smart Serial Interface #0, pin RxData1 (Input)
hm2/hm2_7i76e.0:     IO Pin 014 (P1-11): Muxed Encoder #2, pin Muxed Index (Input)
hm2/hm2_7i76e.0:     IO Pin 015 (P1-12): Muxed Encoder #2, pin Muxed B (Input)
hm2/hm2_7i76e.0:     IO Pin 016 (P1-13): Muxed Encoder #2, pin Muxed A (Input)
hm2/hm2_7i76e.0:     IO Pin 017 (P2-01): IOPort
hm2/hm2_7i76e.0:     IO Pin 018 (P2-14): IOPort
hm2/hm2_7i76e.0:     IO Pin 019 (P2-02): IOPort
hm2/hm2_7i76e.0:     IO Pin 020 (P2-15): IOPort
hm2/hm2_7i76e.0:     IO Pin 021 (P2-03): IOPort
hm2/hm2_7i76e.0:     IO Pin 022 (P2-16): IOPort
hm2/hm2_7i76e.0:     IO Pin 023 (P2-04): IOPort
hm2/hm2_7i76e.0:     IO Pin 024 (P2-17): IOPort
hm2/hm2_7i76e.0:     IO Pin 025 (P2-05): IOPort
hm2/hm2_7i76e.0:     IO Pin 026 (P2-06): IOPort
hm2/hm2_7i76e.0:     IO Pin 027 (P2-07): Muxed Encoder Select #0, pin Mux Select 0 (Output)
hm2/hm2_7i76e.0:     IO Pin 028 (P2-08): Muxed Encoder #0, pin Muxed A (Input)
hm2/hm2_7i76e.0:     IO Pin 029 (P2-09): Muxed Encoder #0, pin Muxed B (Input)
hm2/hm2_7i76e.0:     IO Pin 030 (P2-10): Muxed Encoder #0, pin Muxed Index (Input)
hm2/hm2_7i76e.0:     IO Pin 031 (P2-11): Muxed Encoder #1, pin Muxed A (Input)
hm2/hm2_7i76e.0:     IO Pin 032 (P2-12): Muxed Encoder #1, pin Muxed B (Input)
hm2/hm2_7i76e.0:     IO Pin 033 (P2-13): Muxed Encoder #1, pin Muxed Index (Input)
hm2/hm2_7i76e.0:     IO Pin 034 (P3-01): PWMGen #0, pin Out0 (PWM or Up) (Output)
hm2/hm2_7i76e.0:     IO Pin 035 (P3-14): IOPort
hm2/hm2_7i76e.0:     IO Pin 036 (P3-02): StepGen #5, pin Step (Output)
hm2/hm2_7i76e.0:     IO Pin 037 (P3-15): IOPort
hm2/hm2_7i76e.0:     IO Pin 038 (P3-03): StepGen #5, pin Direction (Output)
hm2/hm2_7i76e.0:     IO Pin 039 (P3-16): IOPort
hm2/hm2_7i76e.0:     IO Pin 040 (P3-04): StepGen #6, pin Step (Output)
hm2/hm2_7i76e.0:     IO Pin 041 (P3-17): IOPort
hm2/hm2_7i76e.0:     IO Pin 042 (P3-05): StepGen #6, pin Direction (Output)
hm2/hm2_7i76e.0:     IO Pin 043 (P3-06): StepGen #7, pin Step (Output)
hm2/hm2_7i76e.0:     IO Pin 044 (P3-07): StepGen #7, pin Direction (Output)
hm2/hm2_7i76e.0:     IO Pin 045 (P3-08): StepGen #8, pin Step (Output)
hm2/hm2_7i76e.0:     IO Pin 046 (P3-09): StepGen #8, pin Direction (Output)
hm2/hm2_7i76e.0:     IO Pin 047 (P3-10): IOPort
hm2/hm2_7i76e.0:     IO Pin 048 (P3-11): IOPort
hm2/hm2_7i76e.0:     IO Pin 049 (P3-12): IOPort
hm2/hm2_7i76e.0:     IO Pin 050 (P3-13): IOPort
hm2/hm2_7i76e.0: registered

Found file(REL): ./mpg.hal
**** GMOCCAPY GETINIINFO **** 
 Preference file path: gmoccapy_preferences
[]
**** GMOCCAPY INFO ****
**** gmoccapy screen 2 found ****
**** GMOCCAPY ERROR ****
**** screen 2 GLADE ERROR: ****
Traceback (most recent call last):
  File "/usr/bin/gmoccapy", line 931, in _check_screen2
    self.builder.add_from_file( screen2 )
GError: Ogiltigt rotelement: "html"
['ntb_user_tabs']
**** GMOCCAPY INFO ****
**** audio available! ****
**** GMOCCAPY INFO ****
**** virtual keyboard program found : <onboard>
****  probe_screen GETINIINFO **** 
 Preference file path: gmoccapy_preferences
**** PROBE SCREEN INFO ****
**** To many increments given in INI File for this screen ****
**** Only the first 5 will be reachable through this screen ****
**** PROBE SCREEN INFO ****
**** no valid probe config in INI File ****
**** disabled auto tool measurement ****
toolnumber = 0 False
**** GMOCCAPY INFO ****
**** replaced btn_zero_g92 to btn_block_height ****
**** GMOCCAPY INFO: Gcode.lang found ****

(gmoccapy:4883): GtkSourceView-CRITICAL **: gtk_source_language_manager_set_search_path: assertion 'lm->priv->ids == NULL' failed
**** GMOCCAPY INFO : inifile = /home/bengt/linuxcnc/configs/GB_3speed/GB_3speed.ini ****:
**** GMOCCAPY INFO : postgui halfile = postgui.hal ****:

(onboard:4896): Gdk-CRITICAL **: gdk_window_thaw_toplevel_updates: assertion 'window->update_and_descendants_freeze_count > 0' failed
estopping / killing gmoccapy
Shutting down and cleaning up LinuxCNC...
task: 5634 cycles, min=0.000022, max=0.097501, avg=0.010099, 0 latency excursions (> 10x expected cycle time of 0.010000s)
hm2_eth: HostMot2 ethernet driver unloaded
hm2: unloading
Note: Using POSIX realtime
bengt@CombiMll ~ $