[Tool0] Type=PlasmaTool Name=1.6 Black Sheet 45amp Comment= Tool\ number=2 Kerf\ width=1.57 Plunge\ rate=3810 Pierce\ delay=1 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=4 Cut\ height=1.5 Pierce\ type=0 Feed\ rate=6858 [Tool1] Type=PlasmaTool Name=0.5mm Mild Sheet FineCut Comment= Tool\ number=4 Kerf\ width=1.3 Plunge\ rate=3810 Pierce\ delay=0 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=2.25 Cut\ height=1.5 Pierce\ type=0 Feed\ rate=4330 [Tool2] Type=PlasmaTool Name=1mm Mild Sheet FineCut Comment= Tool\ number=5 Kerf\ width=1.2 Plunge\ rate=3810 Pierce\ delay=0.2 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=2.25 Cut\ height=1.5 Pierce\ type=0 Feed\ rate=4825 [Tool3] Type=PlasmaTool Name=1.5mm Mild Sheet FineCut Comment= Tool\ number=6 Kerf\ width=1.2 Plunge\ rate=3810 Pierce\ delay=0.4 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=2.25 Cut\ height=1.5 Pierce\ type=0 Feed\ rate=4825 [Tool4] Type=PlasmaTool Name=2mm Mil Sheet FineCut Comment= Tool\ number=7 Kerf\ width=1.2 Plunge\ rate=3810 Pierce\ delay=0.4 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=2.25 Cut\ height=1.5 Pierce\ type=0 Feed\ rate=4740 [Tool5] Type=PlasmaTool Name=3mm Mild Sheet FineCut Comment= Tool\ number=8 Kerf\ width=1.2 Plunge\ rate=3810 Pierce\ delay=0.5 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=2.25 Cut\ height=1.5 Pierce\ type=0 Feed\ rate=3445 [Tool6] Type=PlasmaTool Name=3mm Mild Sheet 45 Amp Comment= Tool\ number=9 Kerf\ width=1.5 Plunge\ rate=3810 Pierce\ delay=0.4 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=5 Cut\ height=3 Pierce\ type=0 Feed\ rate=3725 [Tool7] Type=PlasmaTool Name=5mm Mild Plate 45 Amp Comment= Tool\ number=10 Kerf\ width=1.6 Plunge\ rate=3810 Pierce\ delay=0.5 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=3.8 Cut\ height=1.5 Pierce\ type=0 Feed\ rate=1757.5 [Tool8] Type=PlasmaTool Name=6mm Mild Sheet 65 Amp Comment= Tool\ number=11 Kerf\ width=1.8 Plunge\ rate=3810 Pierce\ delay=0.5 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=3.8 Cut\ height=1.5 Pierce\ type=0 Feed\ rate=2815 [Tool9] Type=PlasmaTool Name=8mm Mild Sheet 65 Amp Comment= Tool\ number=12 Kerf\ width=1.9 Plunge\ rate=3810 Pierce\ delay=1.5 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=3.8 Cut\ height=2 Pierce\ type=0 Feed\ rate=1815 [Tool10] Type=PlasmaTool Name=10mm Mild Sheet 65 Amp Comment= Tool\ number=13 Kerf\ width=2 Plunge\ rate=3810 Pierce\ delay=1 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=6 Cut\ height=3 Pierce\ type=0 Feed\ rate=1085 [Tool11] Type=PlasmaTool Name=12mm Mild Sheet 65 Amp Comment= Tool\ number=14 Kerf\ width=2.2 Plunge\ rate=3810 Pierce\ delay=1.2 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=5.5 Cut\ height=2.5 Pierce\ type=0 Feed\ rate=845 [Tool12] Type=PlasmaTool Name=16mm Mild Sheet 105 Amp Comment= Tool\ number=15 Kerf\ width=2.4 Plunge\ rate=3810 Pierce\ delay=1 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=11.5 Cut\ height=4.6 Pierce\ type=0 Feed\ rate=1050 [Tool13] Type=PlasmaTool Name=20mm Mild Sheet 105 Amp Comment= Tool\ number=16 Kerf\ width=3.2 Plunge\ rate=3810 Pierce\ delay=3 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=11.5 Cut\ height=4.6 Pierce\ type=0 Feed\ rate=780 [Tool14] Type=PlasmaTool Name=25mm Mild Sheet 125 Amp Comment= Tool\ number=17 Kerf\ width=3.1 Plunge\ rate=610 Pierce\ delay=5 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=12 Cut\ height=5 Pierce\ type=0 Feed\ rate=610 [Tool15] Type=PlasmaTool Name=1.6 Stainless FineCut Comment= Tool\ number=18 Kerf\ width=1 Plunge\ rate=3810 Pierce\ delay=0.4 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=2.03 Cut\ height=0.51 Pierce\ type=0 Feed\ rate=4825 [Tool16] Type=PlasmaTool Name=10mm Mild Sheet 105 Amp Comment= Tool\ number=19 Kerf\ width=2.2 Plunge\ rate=3810 Pierce\ delay=1.5 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=9.199999999999999 Cut\ height=4.6 Pierce\ type=0 Feed\ rate=2410 [Tool17] Type=PlasmaTool Name=8mm Mild Sheet 105 Amp Comment= Tool\ number=20 Kerf\ width=2.1 Plunge\ rate=3810 Pierce\ delay=0.8 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=9.199999999999999 Cut\ height=4.6 Pierce\ type=0 Feed\ rate=3220 [Tool18] Type=PlasmaTool Name=12mm Mild Sheet 105 Amp Comment= Tool\ number=21 Kerf\ width=2.3 Plunge\ rate=3810 Pierce\ delay=1 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=9.199999999999999 Cut\ height=4.6 Pierce\ type=0 Feed\ rate=1810 [Tool19] Type=PlasmaTool Name=Center Spot Comment= Tool\ number=22 Kerf\ width=1.2 Plunge\ rate=3810 Pierce\ delay=0 Pause\ at\ end\ of\ cut=0 Wiggle\ length=10 Pierce\ height=2 Cut\ height=2 Pierce\ type=0 Feed\ rate=4825 [Tool20] Type=CodeTool Name=DTHC-OFF Comment= Tool\ number=268435457 Code=M62 P2 (DTHC OFF) [Tool21] Type=CodeTool Name=DTHC-ON Comment= Tool\ number=268435458 Code=M63 P2 (DTHC ON) [pathRules] GlobalRule=-1 [pathRules/Set0] name=Holes [pathRules/Set0/Rule0] Class=PathRuleOnCircle Feed\ rate=0.65 Start\ code=268435457 End\ code=268435458 Enabled=1 Smaller\ than=38.100000000000001 [pathRules/Set1] name=EOCAnti-Dive [pathRules/Set1/Rule0] Class=PathRuleOnStart Feed\ rate=1 Start\ code=268435458 End\ code=-1 Enabled=1 Distance=5 [pathRules/Set1/Rule1] Class=PathRuleBeforeEnd Feed\ rate=1 Start\ code=268435457 End\ code=-1 Enabled=1 Distance=14 Include\ leadout=0