# Generated by PNCconf at Thu Aug 1 12:44:14 2019 # If you make changes to this file, they will be # overwritten when you run PNCconf again loadrt trivkins loadrt [EMCMOT]EMCMOT servo_period_nsec=[EMCMOT]SERVO_PERIOD num_joints=[TRAJ]AXES loadrt hostmot2 loadrt hm2_pci config=" num_encoders=1 num_pwmgens=0 num_stepgens=5 sserial_port_0=00xxxx" setp hm2_5i25.0.watchdog.timeout_ns 5000000 loadrt hal_parport cfg="0 out" loadrt pid names=pid.x,pid.y,pid.z,pid.s loadrt abs names=abs.spindle loadrt lowpass names=lowpass.spindle addf parport.0.read servo-thread addf hm2_5i25.0.read servo-thread addf motion-command-handler servo-thread addf motion-controller servo-thread addf pid.x.do-pid-calcs servo-thread addf pid.y.do-pid-calcs servo-thread addf pid.z.do-pid-calcs servo-thread addf pid.s.do-pid-calcs servo-thread addf abs.spindle servo-thread addf lowpass.spindle servo-thread addf parport.0.write servo-thread addf hm2_5i25.0.write servo-thread # external output signals # external input signals # --- MIN-HOME-X --- net min-home-x <= hm2_5i25.0.7i76.0.0.input-00-not # --- MIN-HOME-Y --- net min-home-y <= hm2_5i25.0.7i76.0.0.input-02-not # --- MAX-HOME-Z --- net max-home-z <= hm2_5i25.0.7i76.0.0.input-04-not #******************* # AXIS X #******************* setp pid.x.Pgain [AXIS_0]P setp pid.x.Igain [AXIS_0]I setp pid.x.Dgain [AXIS_0]D setp pid.x.bias [AXIS_0]BIAS setp pid.x.FF0 [AXIS_0]FF0 setp pid.x.FF1 [AXIS_0]FF1 setp pid.x.FF2 [AXIS_0]FF2 setp pid.x.deadband [AXIS_0]DEADBAND setp pid.x.maxoutput [AXIS_0]MAX_OUTPUT setp pid.x.error-previous-target true net x-index-enable <=> pid.x.index-enable net x-enable => pid.x.enable net x-pos-cmd => pid.x.command net x-pos-fb => pid.x.feedback net x-output => pid.x.output # Step Gen signals/setup setp hm2_5i25.0.stepgen.00.dirsetup [AXIS_0]DIRSETUP setp hm2_5i25.0.stepgen.00.dirhold [AXIS_0]DIRHOLD setp hm2_5i25.0.stepgen.00.steplen [AXIS_0]STEPLEN setp hm2_5i25.0.stepgen.00.stepspace [AXIS_0]STEPSPACE setp hm2_5i25.0.stepgen.00.position-scale [AXIS_0]STEP_SCALE setp hm2_5i25.0.stepgen.00.step_type 0 setp hm2_5i25.0.stepgen.00.control-type 1 setp hm2_5i25.0.stepgen.00.maxaccel [AXIS_0]STEPGEN_MAXACCEL setp hm2_5i25.0.stepgen.00.maxvel [AXIS_0]STEPGEN_MAXVEL # ---closedloop stepper signals--- net x-pos-cmd <= axis.0.motor-pos-cmd net x-vel-cmd <= axis.0.joint-vel-cmd net x-output <= hm2_5i25.0.stepgen.00.velocity-cmd net x-pos-fb <= hm2_5i25.0.stepgen.00.position-fb net x-pos-fb => axis.0.motor-pos-fb net x-enable <= axis.0.amp-enable-out net x-enable => hm2_5i25.0.stepgen.00.enable # ---setup home / limit switch signals--- net min-home-x => axis.0.home-sw-in net min-home-x => axis.0.neg-lim-sw-in net x-pos-limit => axis.0.pos-lim-sw-in #******************* # AXIS Y #******************* setp pid.y.Pgain [AXIS_1]P setp pid.y.Igain [AXIS_1]I setp pid.y.Dgain [AXIS_1]D setp pid.y.bias [AXIS_1]BIAS setp pid.y.FF0 [AXIS_1]FF0 setp pid.y.FF1 [AXIS_1]FF1 setp pid.y.FF2 [AXIS_1]FF2 setp pid.y.deadband [AXIS_1]DEADBAND setp pid.y.maxoutput [AXIS_1]MAX_OUTPUT setp pid.y.error-previous-target true net y-index-enable <=> pid.y.index-enable net y-enable => pid.y.enable net y-pos-cmd => pid.y.command net y-pos-fb => pid.y.feedback net y-output => pid.y.output # Step Gen signals/setup setp hm2_5i25.0.stepgen.01.dirsetup [AXIS_1]DIRSETUP setp hm2_5i25.0.stepgen.01.dirhold [AXIS_1]DIRHOLD setp hm2_5i25.0.stepgen.01.steplen [AXIS_1]STEPLEN setp hm2_5i25.0.stepgen.01.stepspace [AXIS_1]STEPSPACE setp hm2_5i25.0.stepgen.01.position-scale [AXIS_1]STEP_SCALE setp hm2_5i25.0.stepgen.01.step_type 0 setp hm2_5i25.0.stepgen.01.control-type 1 setp hm2_5i25.0.stepgen.01.maxaccel [AXIS_1]STEPGEN_MAXACCEL setp hm2_5i25.0.stepgen.01.maxvel [AXIS_1]STEPGEN_MAXVEL # ---closedloop stepper signals--- net y-pos-cmd <= axis.1.motor-pos-cmd net y-vel-cmd <= axis.1.joint-vel-cmd net y-output <= hm2_5i25.0.stepgen.01.velocity-cmd net y-pos-fb <= hm2_5i25.0.stepgen.01.position-fb net y-pos-fb => axis.1.motor-pos-fb net y-enable <= axis.1.amp-enable-out net y-enable => hm2_5i25.0.stepgen.01.enable # ---setup home / limit switch signals--- net min-home-y => axis.1.home-sw-in net min-home-y => axis.1.neg-lim-sw-in net y-pos-limit => axis.1.pos-lim-sw-in #******************* # AXIS Z #******************* setp pid.z.Pgain [AXIS_2]P setp pid.z.Igain [AXIS_2]I setp pid.z.Dgain [AXIS_2]D setp pid.z.bias [AXIS_2]BIAS setp pid.z.FF0 [AXIS_2]FF0 setp pid.z.FF1 [AXIS_2]FF1 setp pid.z.FF2 [AXIS_2]FF2 setp pid.z.deadband [AXIS_2]DEADBAND setp pid.z.maxoutput [AXIS_2]MAX_OUTPUT setp pid.z.error-previous-target true net z-index-enable <=> pid.z.index-enable net z-enable => pid.z.enable net z-pos-cmd => pid.z.command net z-pos-fb => pid.z.feedback net z-output => pid.z.output # Step Gen signals/setup setp hm2_5i25.0.stepgen.02.dirsetup [AXIS_2]DIRSETUP setp hm2_5i25.0.stepgen.02.dirhold [AXIS_2]DIRHOLD setp hm2_5i25.0.stepgen.02.steplen [AXIS_2]STEPLEN setp hm2_5i25.0.stepgen.02.stepspace [AXIS_2]STEPSPACE setp hm2_5i25.0.stepgen.02.position-scale [AXIS_2]STEP_SCALE setp hm2_5i25.0.stepgen.02.step_type 0 setp hm2_5i25.0.stepgen.02.control-type 1 setp hm2_5i25.0.stepgen.02.maxaccel [AXIS_2]STEPGEN_MAXACCEL setp hm2_5i25.0.stepgen.02.maxvel [AXIS_2]STEPGEN_MAXVEL # ---closedloop stepper signals--- net z-pos-cmd <= axis.2.motor-pos-cmd net z-vel-cmd <= axis.2.joint-vel-cmd net z-output <= hm2_5i25.0.stepgen.02.velocity-cmd net z-pos-fb <= hm2_5i25.0.stepgen.02.position-fb net z-pos-fb => axis.2.motor-pos-fb net z-enable <= axis.2.amp-enable-out net z-enable => hm2_5i25.0.stepgen.02.enable # ---setup home / limit switch signals--- net max-home-z => axis.2.home-sw-in net max-home-z => axis.2.neg-lim-sw-in net z-pos-limit => axis.2.pos-lim-sw-in #******************* # SPINDLE S #******************* setp pid.s.Pgain [SPINDLE_9]P setp pid.s.Igain [SPINDLE_9]I setp pid.s.Dgain [SPINDLE_9]D setp pid.s.bias [SPINDLE_9]BIAS setp pid.s.FF0 [SPINDLE_9]FF0 setp pid.s.FF1 [SPINDLE_9]FF1 setp pid.s.FF2 [SPINDLE_9]FF2 setp pid.s.deadband [SPINDLE_9]DEADBAND setp pid.s.maxoutput [SPINDLE_9]MAX_OUTPUT setp pid.s.error-previous-target true #setp pid.s.maxerror .0005 net spindle-index-enable <=> pid.s.index-enable net spindle-enable => pid.s.enable net spindle-vel-cmd-rpm => pid.s.command net spindle-vel-fb-rpm => pid.s.feedback net spindle-output <= pid.s.output # ---digital potentionmeter output signals/setup--- setp hm2_5i25.0.7i76.0.0.spinout-minlim [SPINDLE_9]OUTPUT_MIN_LIMIT setp hm2_5i25.0.7i76.0.0.spinout-maxlim [SPINDLE_9]OUTPUT_MAX_LIMIT setp hm2_5i25.0.7i76.0.0.spinout-scalemax [SPINDLE_9]OUTPUT_SCALE net spindle-vel-cmd-rpm => hm2_5i25.0.7i76.0.0.spinout net machine-is-enabled => hm2_5i25.0.7i76.0.0.spinena net spindle-ccw => hm2_5i25.0.7i76.0.0.spindir # ---setup spindle control signals--- net spindle-vel-cmd-rps <= motion.spindle-speed-out-rps net spindle-vel-cmd-rps-abs <= motion.spindle-speed-out-rps-abs net spindle-vel-cmd-rpm <= motion.spindle-speed-out net spindle-vel-cmd-rpm-abs <= motion.spindle-speed-out-abs net spindle-enable <= motion.spindle-on net spindle-cw <= motion.spindle-forward net spindle-ccw <= motion.spindle-reverse net spindle-brake <= motion.spindle-brake net spindle-revs => motion.spindle-revs net spindle-at-speed => motion.spindle-at-speed net spindle-vel-fb-rps => motion.spindle-speed-in net spindle-index-enable <=> motion.spindle-index-enable # ---Setup spindle at speed signals--- sets spindle-at-speed true #****************************** # connect miscellaneous signals #****************************** # ---HALUI signals--- net joint-select-a halui.joint.0.select net x-is-homed halui.joint.0.is-homed net jog-x-pos halui.jog.0.plus net jog-x-neg halui.jog.0.minus net jog-x-analog halui.jog.0.analog net joint-select-b halui.joint.1.select net y-is-homed halui.joint.1.is-homed net jog-y-pos halui.jog.1.plus net jog-y-neg halui.jog.1.minus net jog-y-analog halui.jog.1.analog net joint-select-c halui.joint.2.select net z-is-homed halui.joint.2.is-homed net jog-z-pos halui.jog.2.plus net jog-z-neg halui.jog.2.minus net jog-z-analog halui.jog.2.analog net jog-selected-pos halui.jog.selected.plus net jog-selected-neg halui.jog.selected.minus net spindle-manual-cw halui.spindle.forward net spindle-manual-ccw halui.spindle.reverse net spindle-manual-stop halui.spindle.stop net machine-is-on halui.machine.is-on net jog-speed halui.jog-speed net MDI-mode halui.mode.is-mdi # ---coolant signals--- net coolant-mist <= iocontrol.0.coolant-mist net coolant-flood <= iocontrol.0.coolant-flood # ---probe signal--- net probe-in => motion.probe-input # ---motion control signals--- net in-position <= motion.in-position net machine-is-enabled <= motion.motion-enabled # ---digital in / out signals--- # ---estop signals--- net estop-out <= iocontrol.0.user-enable-out net estop-out => iocontrol.0.emc-enable-in # ---manual tool change signals--- loadusr -W hal_manualtoolchange net tool-change-request iocontrol.0.tool-change => hal_manualtoolchange.change net tool-change-confirmed iocontrol.0.tool-changed <= hal_manualtoolchange.changed net tool-number iocontrol.0.tool-prep-number => hal_manualtoolchange.number net tool-prepare-loopback iocontrol.0.tool-prepare => iocontrol.0.tool-prepared