function OnAbout(event)
   ctrl = event:GetTextCtrl()
   ctrl:AppendText("LinuxCNC plasma post processor\n")
   ctrl:AppendText("\n")
   ctrl:AppendText("Modal G-codes and coordinates\n")
   ctrl:AppendText("Comments enclosed with ( and )\n")
   ctrl:AppendText("Incremental IJ\n")
   ctrl:AppendText("uses G43 tool length offsets\n")
end


--  revision 3/2/07
--  Removed final safety move. This is now done in SheetCam

--   revision 7/10/04
--   Added new arc handling

--   Created 30/3/2005
--   based on Mach2.post



function OnInit()
   post.SetCommentChars ("()", "[]")  --make sure ( and ) characters do not appear in system text
   post.Text (" (Filename: ", fileName, ")\n")
   post.Text (" (Post processor: ", postName, ")\n")
   post.Text (" (Date: ", date, ")\n")
   if(scale == metric) then
      post.Text (" G21 (Units: Metric)\n") --metric mode
   else
      post.Text (" G20 (Units: Inches)\n") --inch mode
   end
   post.Text (" G40 G90\n F1 S1\n")
   bigArcs = 1 --stitch arc segments together
   minArcSize = 0.05 --arcs smaller than this are converted to moves
end

function OnNewLine()
   post.Text ("N")
   post.Number (lineNumber, "0000")
   lineNumber = lineNumber + 10
end


function OnFinish()
   post.Text (" M05 M30\n")
end

function OnRapid()
   post.ModalText (" G00")
   post.ModalNumber (" X", endX * scale, "0.0000")
   post.ModalNumber (" Y", endY * scale, "0.0000")
   post.ModalNumber (" Z", (endZ + toolOffset) * scale, "0.0000")
   post.Eol()
end

function OnMove()
   post.ModalText (" G01")
   post.ModalNumber (" X", endX * scale, "0.0000")
   post.ModalNumber (" Y", endY * scale, "0.0000")
   post.ModalNumber (" Z", (endZ + toolOffset) * scale, "0.0000")
   post.ModalNumber (" F", feedRate * scale, "0.###")
   post.Eol()
end

function OnArc()
   if(arcAngle <0) then
      post.ModalText (" G03")
   else
      post.ModalText (" G02")
   end
   post.NonModalNumber (" X", endX * scale, "0.0000")
   post.NonModalNumber (" Y", endY * scale, "0.0000")
   post.ModalNumber (" Z", (endZ + toolOffset) * scale, "0.0000")
   post.Text (" I")
   post.Number ((arcCentreX - currentX) * scale, "0.0000")
   post.Text (" J")
   post.Number ((arcCentreY - currentY) * scale, "0.0000")
   post.ModalNumber (" F", feedRate * scale, "0.0###")
   post.Eol()
end


function OnPenDown()
   post.NonModalNumber("o<touchoff> call [" ,pierceHeight * scale ,"0.00" )
      post.Text ("] ")
   post.NonModalNumber("[", pierceDelay * scale, "0.##")
   post.Text ("] ")
   post.NonModalNumber("[", cutHeight * scale, "0.##")
   post.Text ("] (Touchoff and start cutting)\n")
   post.NonModalNumber ("F", feedRate * scale, "0.###")
   post.Eol()
  end


function OnPenUp()
   post.Text (" M05\n")
   if (endDelay > 0) then
      post.Text (" G04 P")
      post.Number (endDelay,"0.###")
      post.Eol()
   end
end

function OnNewOperation()
   post.Text (" (Operation: ", operationName, ")\n")
end

function OnComment()
  post.Text(" (",commentText,")\n")
end


function OnNewPart()
   post.Text(" (Part: ",partName,")\n");
end


function OnDrill()
   OnRapid()
   OnPenDown()
   endZ = drillZ
   OnMove()
   OnPenUp()
   endZ = safeZ
   OnRapid()
end