(1001)
N10 G21
N15 G90 G40
N20 G17 G91.1
N25 G64 P0.254 Q0.254
N30 M52 P1.
N35 M65 P2.
N40 M65 P3.
N45 M68 E3 Q0.

(2D PROFILE SMALL HOLES)
(--------------------------------------------------------------------------------------------------)
(- THIS SECTION IS SET UP TO CUT SMALL HOLES ONLY.                                                -)
(- IT WILL AUTOMATICALLY SLOW THE CUT SPEED FOR THE HOLES BASED ON THE SETTING IN THE PARAMETERS. -)
(- IT WILL ALSO CREATE AN ARC LEAD-IN FOR EACH HOLE STARTING AT THE CENTER OF THE HOLE.           -)
(- ANY OTHER TYPE OF OPERATIONS IN THIS SECTION WILL NOT WORK CORRECTLY                           -)
(- THIS SETUP HAS OCCURRED DUE TO DISABLING LEAD IN ON THE LEADS PAGE                             -)
(- BE CERTAIN YOU HAVE ALSO SET PIERCE CLEARANCE TO 0 OR YOU WILL NOT GET THE CORRECT RESULTS     -)
(--------------------------------------------------------------------------------------------------)
(PLASMA CUTTING)
(THROUGH CUTTING)

N50 M190 P37.
N55 M66 P3. L3 Q1.
N60 F#<_hal[plasmac.cut-feed-rate]>
N65 G0 X50. Y45.75
N70 G0 Y50.
(SMALL HOLE WITH ARC LEAD-IN FROM CENTER POINT AND 4MM OVERCUT WITH TORCH OFF)
N75 M3 $0 S1
N80 M67 E3 Q60.
N85 G3 Y45.75 J-2.125
N90 J4.25
N95 M62 P3.
N100 X53.43507 Y47.49744 J4.25
N105 M63 P3.
N110 M67 E3 Q100.
N115 M5
N120 G0 X50. Y45.75
N125 X49.08121 Y39.37944
N130 G3 X48.9234 Y38.6532 I1.59219 J-0.72625
N135 G1 Y23.6532
N140 G3 X52.4234 I1.75
N145 G1 Y38.6532
N150 G3 X49.08121 Y39.37944 I-1.75
N155 M5
N160 G0 X36.98129 Y39.55513
N165 X32. Y35.
(SMALL HOLE WITH ARC LEAD-IN FROM CENTER POINT AND 4MM OVERCUT WITH TORCH OFF)
N170 M3 $0 S1
N175 M67 E3 Q60.
N180 G3 X36.98129 Y39.55513 I2.49064 J2.27757
N185 I-4.98129 J-4.55513
N190 M62 P3.
N195 X33.58785 Y41.56058 I-4.98129 J-4.55513
N200 M63 P3.
N205 M67 E3 Q100.
N210 M5
N215 G0 X36.98129 Y39.55513
N220 X34.03905 Y47.40825
N225 X36. Y50.
(SMALL HOLE WITH ARC LEAD-IN FROM CENTER POINT AND 4MM OVERCUT WITH TORCH OFF)
N230 M3 $0 S1
N235 M67 E3 Q60.
N240 G3 X34.03905 Y47.40825 I-0.98047 J-1.29588
N245 I1.96095 J2.59175
N250 M62 P3.
N255 X37.78936 Y47.28694 I1.96095 J2.59175
N260 M63 P3.
N265 M67 E3 Q100.
N270 M5
N275 G0 X34.03905 Y47.40825
N280 X23.74684 Y48.58188
N285 X22. Y50.
(SMALL HOLE WITH ARC LEAD-IN FROM CENTER POINT AND 4MM OVERCUT WITH TORCH OFF)
N290 M3 $0 S1
N295 M67 E3 Q60.
N300 G3 X23.74684 Y48.58188 I0.87342 J-0.70906
N305 I-1.74684 J1.41812
N310 M62 P3.
N315 X23.02886 Y52.00099 I-1.74684 J1.41812
N320 M63 P3.
N325 M67 E3 Q100.
N330 M5
N335 G0 X23.74684 Y48.58188
N340 X10.94646 Y48.52802
N345 X10. Y50.
(SMALL HOLE WITH ARC LEAD-IN FROM CENTER POINT AND 4MM OVERCUT WITH TORCH OFF)
N350 M3 $0 S1
N355 M67 E3 Q60.
N360 G3 X10.94646 Y48.52802 I0.47323 J-0.73599
N365 I-0.94646 J1.47198
N370 M62 P3.
N375 X10.4911 Y51.67968 I-0.94646 J1.47198
N380 M63 P3.
N385 M67 E3 Q100.
N390 M5
N395 G0 X10.94646 Y48.52802
N400 X11.765 Y29.89733
N405 X13. Y35.
(SMALL HOLE WITH ARC LEAD-IN FROM CENTER POINT AND 4MM OVERCUT WITH TORCH OFF)
N410 M3 $0 S1
N415 M67 E3 Q60.
N420 G3 X11.765 Y29.89733 I-0.6175 J-2.55134
N425 I1.235 J5.10267
N430 M62 P3.
N435 X15.62883 Y30.45558 I1.235 J5.10267
N440 M63 P3.
N445 M67 E3 Q100.
N450 M5
N455 G0 X11.765 Y29.89733
N460 X11.3454 Y20.80332
N465 G1 X6.90733 Y18.24099
N470 Y12.17881
N475 X12.1573 Y9.14769
N480 X17.4073 Y12.17881
N485 Y18.24099
N490 X12.1573 Y21.27207
N495 X11.3454 Y20.80332
N500 M5

(2D PROFILE OUTSIDE)
(--------------------------------------------------)
(- THIS SECTION HAS REVERTED TO NORMAL OPERATION. -)
(--------------------------------------------------)
N505 G0 X-4.84808 Y0.69242
N510 M3 $0 S1
N515 G41.1 D#<_hal[plasmac_run.kerf-width-f]>
N520 G1 X-4.47308 Y0.0429
N525 X-1.875 Y1.5429
N530 G3 X0. Y4.7905 I-1.875 J3.2476
N535 G1 Y60.
N540 X60.
N545 Y0.
N550 X0.
N555 Y4.7905
N560 G3 X-1.875 Y8.03809 I-3.75
N565 G1 X-4.47308 Y9.53809
N570 G40
N575 X-4.84808 Y8.88857
N580 M5

N585 G0 X0. Y0.
N590 G90
N595 G40
N600 M65 P2.
N605 M65 P3.
N610 M68 E3 Q0.
N615 M5
N620 M30