# this section only reqired if using the sim testing panel # [APPLICATIONS] # DELAY = 3 # APP = ./test/plasmac_test.py # required [PLASMAC] # required for upgrades (DO NOT CHANGE) LAST_UPGRADE = 0.097 # sets the operating mode, if not specified the default is 0 # 0 = use arc-voltage-in for arcOK and THC (no need to connect arc-ok-in, move-up-in and move-down-in) # 1 = use arc-ok-in for arcOK and arc-voltage-in for THC (no need to connect move-up-in and move-down-in) # 2 = use arc-ok-in for arcOK and move-down-in + move-up-in for THC (no need to connect arc-voltage-in) MODE = 0 # enable(0) or disable(1) the plasmac config page, if not specified the default is enabled CONFIG_DISABLE = 0 # the font for the Axis GUI, if not specified 'sans 10' will be used # valid font sizes are from 9 to 15 FONT = sans 11 # the window size for the Axis GUI, 0 = minimum size to suit font, 1 = maximized MAXIMISED = 0 # the theme for the Axis GUI tabs, if not specified the system theme will be used THEME = Clearlooks # percentage of cut-feed-rate used for paused motion speed PAUSED_MOTION_SPEED = 50 # torch on time when manual pulse requested TORCH_PULSE_TIME = 1.0 # for Powermax communications #PM_PORT = /dev/ttyUSB0 #PM_PRESSURE_DISPLAY = psi # for the five user buttons in the main window BUTTON_1_NAME = Ohmic\Test BUTTON_1_CODE = ohmic-test BUTTON_2_NAME = Probe\Test BUTTON_2_CODE = probe-test 30 BUTTON_3_NAME = Change\Consumables BUTTON_3_CODE = change-consumables X0 F160 BUTTON_4_NAME = Pierce\& Cut BUTTON_4_CODE = cut-type BUTTON_5_NAME = Load\Sheet BUTTON_5_CODE = G53 G0 X{JOINT_0 HOME} Y1 # for the ten user buttons in the Extras panel BUTTON_10_NAME = BUTTON_10_CODE = BUTTON_10_IMAGE = BUTTON_11_NAME = BUTTON_11_CODE = BUTTON_11_IMAGE = BUTTON_12_NAME = BUTTON_12_CODE = BUTTON_12_IMAGE = BUTTON_13_NAME = BUTTON_13_CODE = BUTTON_13_IMAGE = BUTTON_14_NAME = PlasmaC\User Guide BUTTON_14_CODE = %xdg-open http://linuxcnc.org/docs/devel/html/plasma/plasmac-user-guide.html BUTTON_14_IMAGE = BUTTON_15_NAME = BUTTON_15_CODE = BUTTON_15_IMAGE = BUTTON_16_NAME = BUTTON_16_CODE = BUTTON_16_IMAGE = BUTTON_17_NAME = BUTTON_17_CODE = BUTTON_17_IMAGE = BUTTON_18_NAME = BUTTON_18_CODE = BUTTON_18_IMAGE = BUTTON_19_NAME = LinuxCNC\Docs BUTTON_19_CODE = %xdg-open http://linuxcnc.org/docs/devel/html BUTTON_19_IMAGE = # this section required as is for removing z axis moves from the loaded gcode file # this is optional and if used then plasmac_gcode.py needs to be set as executable [FILTER] PROGRAM_EXTENSION = .ngc remove z axis stuff ngc = ./plasmac_gcode.py nc = ./plasmac_gcode.py tap = ./plasmac_gcode.py [RS274NGC] RS274NGC_STARTUP_CODE = o call PARAMETER_FILE = imperial_parameters.txt # required, ./ must be in this path SUBROUTINE_PATH = ./:../../nc_files/subroutines # required for reading ini and hal variables FEATURES = 12 # required for our material change USER_M_PATH = ./ [HAL] # required TWOPASS = ON # the base machine HALFILE = plasma1.hal # the plasmac component connections HALFILE = plasmac.tcl # the plasmac machine connections HALFILE = plasma1_connections.hal # use this for customisation after GUI has loaded POSTGUI_HALFILE = postgui.hal # required HALUI = halui [DISPLAY] DISPLAY = axis POSITION_OFFSET = RELATIVE POSITION_FEEDBACK = ACTUAL MAX_FEED_OVERRIDE = 2.000000 MAX_SPINDLE_OVERRIDE = 1.000000 MIN_SPINDLE_OVERRIDE = 0.500000 INTRO_GRAPHIC = linuxcnc.gif INTRO_TIME = 5 PROGRAM_PREFIX = /home/aaron/linuxcnc/nc_files INCREMENTS = .1in .05in .01in .005in .001in .0005in .0001in POSITION_FEEDBACK = ACTUAL DEFAULT_LINEAR_VELOCITY = 0.250000 MAX_LINEAR_VELOCITY = 5.000000 MIN_LINEAR_VELOCITY = 0.016670 DEFAULT_ANGULAR_VELOCITY = 12.000000 MAX_ANGULAR_VELOCITY = 180.000000 MIN_ANGULAR_VELOCITY = 1.666667 EDITOR = gedit GEOMETRY = xyz OPEN_FILE = "" TOOL_EDITOR = tooledit x y CYCLE_TIME = 0.1 # required USER_COMMAND_FILE = plasmac_axis.py # required EMBED_TAB_NAME = Statistics EMBED_TAB_COMMAND = gladevcp -c plasmac_stats -x {XID} -u ./plasmac_stats.py -H ./plasmac_stats.hal plasmac_stats.glade # use one of the next two # run panel in tab behind preview EMBED_TAB_NAME = Run EMBED_TAB_COMMAND = gladevcp -c plasmac_run -x {XID} -u ./plasmac_run.py -H plasmac_run.hal plasmac_run_tab.glade # run panel in panel on right side #GLADEVCP = -c plasmac_run -u ./plasmac_run.py -H plasmac_run.hal plasmac_run_panel.glade EMBED_TAB_NAME = Config EMBED_TAB_COMMAND = gladevcp -c plasmac_config -x {XID} -u ./plasmac_config.py -H plasmac_config.hal plasmac_config.glade EMBED_TAB_NAME = Extras EMBED_TAB_COMMAND = halcmd loadusr -Wn plasmac_wizards gladevcp -c plasmac_wizards -x {XID} -u ./plasmac_wizards.py plasmac_wizards.glade [EMC] MACHINE = plasma1 DEBUG = 0 VERSION = 1.1 [TASK] TASK = milltask CYCLE_TIME = 0.010 [EMCMOT] EMCMOT = motmod COMM_TIMEOUT = 1.0 SERVO_PERIOD = 1000000 [HMOT] # **** This is for info only **** CARD0=hm2_7i96.0 [HALUI] [KINS] JOINTS = 4 KINEMATICS = trivkins coordinates=XYYZ kinstype=BOTH [TRAJ] SPINDLES = 3 COORDINATES = XYYZ LINEAR_UNITS = inch ANGULAR_UNITS = degree DEFAULT_LINEAR_VELOCITY = 0.17 MAX_LINEAR_VELOCITY = 1.67 NO_FORCE_HOMING = 1 [EMCIO] EMCIO = io CYCLE_TIME = 0.100 TOOL_TABLE = tool.tbl #****************************************** [AXIS_X] # set to double the value in the corresponding joint MAX_VELOCITY = 3.33333333334 # set to double the value in the corresponding joint MAX_ACCELERATION = 20.0 # shares the above two equally between the joint and the offset OFFSET_AV_RATIO = 0.5 MIN_LIMIT = -48.0 MAX_LIMIT = 48.0 [JOINT_0] TYPE = LINEAR HOME = 0.0 FERROR = 0.5 MIN_FERROR = 0.05 MAX_VELOCITY = 1.66666666667 MAX_ACCELERATION = 10.0 # The values below should be 25% larger than MAX_VELOCITY and MAX_ACCELERATION # If using BACKLASH compensation STEPGEN_MAXACCEL should be 100% larger. STEPGEN_MAXVEL = 2.08 STEPGEN_MAXACCEL = 12.50 P = 1000.0 I = 0.0 D = 0.0 FF0 = 0.0 FF1 = 1.0 FF2 = 0.0 BIAS = 0.0 DEADBAND = 0.0 MAX_OUTPUT = 0.0 # these are in nanoseconds DIRSETUP = 3500 DIRHOLD = 3500 STEPLEN = 10000 STEPSPACE = 8000 STEP_SCALE = -848.797 MIN_LIMIT = -48.0 MAX_LIMIT = 48.0 HOME_OFFSET = 0.0 #****************************************** #****************************************** [AXIS_Y] # set to double the value in the corresponding joint MAX_VELOCITY = 3.33333333334 # set to double the value in the corresponding joint MAX_ACCELERATION = 20.0 # shares the above two equally between the joint and the offset OFFSET_AV_RATIO = 0.5 MIN_LIMIT = -0.001 MAX_LIMIT = 48.0 [JOINT_1] TYPE = LINEAR HOME = 0.0 FERROR = 0.5 MIN_FERROR = 0.05 MAX_VELOCITY = 1.66666666667 MAX_ACCELERATION = 10.0 # The values below should be 25% larger than MAX_VELOCITY and MAX_ACCELERATION # If using BACKLASH compensation STEPGEN_MAXACCEL should be 100% larger. STEPGEN_MAXVEL = 2.08 STEPGEN_MAXACCEL = 12.50 P = 1000.0 I = 0.0 D = 0.0 FF0 = 0.0 FF1 = 1.0 FF2 = 0.0 BIAS = 0.0 DEADBAND = 0.0 MAX_OUTPUT = 0.0 # these are in nanoseconds DIRSETUP = 3500 DIRHOLD = 3500 STEPLEN = 10000 STEPSPACE = 8000 STEP_SCALE = -848.797 MIN_LIMIT = -0.001 MAX_LIMIT = 48.0 HOME_OFFSET = 0.0 [JOINT_2] TYPE = LINEAR HOME = 0.0 FERROR = 0.5 MIN_FERROR = 0.05 MAX_VELOCITY = 1.66666666667 MAX_ACCELERATION = 10.0 # The values below should be 25% larger than MAX_VELOCITY and MAX_ACCELERATION # If using BACKLASH compensation STEPGEN_MAXACCEL should be 100% larger. STEPGEN_MAXVEL = 2.08 STEPGEN_MAXACCEL = 12.50 P = 1000.0 I = 0.0 D = 0.0 FF0 = 0.0 FF1 = 1.0 FF2 = 0.0 BIAS = 0.0 DEADBAND = 0.0 MAX_OUTPUT = 0.0 # these are in nanoseconds DIRSETUP = 3500 DIRHOLD = 3500 STEPLEN = 10000 STEPSPACE = 8000 STEP_SCALE = -848.797 MIN_LIMIT = -0.001 MAX_LIMIT = 48.0 HOME_OFFSET = 0.0 #****************************************** #****************************************** [AXIS_Z] # set to double the value in the corresponding joint MAX_VELOCITY = 2.0 # set to double the value in the corresponding joint MAX_ACCELERATION = 20.0 # shares the above two equally between the joint and the offset OFFSET_AV_RATIO = 0.5 MIN_LIMIT = -0.5 MAX_LIMIT = 3.0 [JOINT_3] TYPE = LINEAR HOME = 0.5 FERROR = 0.5 MIN_FERROR = 0.05 MAX_VELOCITY = 1.0 MAX_ACCELERATION = 10.0 # The values below should be 25% larger than MAX_VELOCITY and MAX_ACCELERATION # If using BACKLASH compensation STEPGEN_MAXACCEL should be 100% larger. STEPGEN_MAXVEL = 1.25 STEPGEN_MAXACCEL = 12.50 P = 1000.0 I = 0.0 D = 0.0 FF0 = 0.0 FF1 = 1.0 FF2 = 0.0 BIAS = 0.0 DEADBAND = 0.0 MAX_OUTPUT = 0.0 # these are in nanoseconds DIRSETUP = 3500 DIRHOLD = 3500 STEPLEN = 10000 STEPSPACE = 800 STEP_SCALE = 3750.0 MIN_LIMIT = -0.5 MAX_LIMIT = 3.0 HOME_OFFSET = 0.5 #****************************************** [SPINDLE_0] P = 0 I = 0 D = 0 FF0 = 1 FF1 = 0 FF2 = 0 BIAS = 0 DEADBAND = 0 MAX_OUTPUT = 2000