*  Executing task in folder ESP32_LinuxCNC_MotionController_RealTime-main: platformio run --target upload --environment esp32-rmii-ethernet --upload-port /dev/ttyACM0 

Processing esp32-rmii-ethernet (platform: espressif32@6.5.0; board: esp32dev; framework: arduino)
-------------------------------------------------------------------------------------------------------------------------------
Verbose mode can be enabled via `-v, --verbose` option
CONFIGURATION: https://docs.platformio.org/page/boards/espressif32/esp32dev.html
PLATFORM: Espressif 32 (6.5.0) > Espressif ESP32 Dev Module
HARDWARE: ESP32 240MHz, 320KB RAM, 4MB Flash
DEBUG: Current (cmsis-dap) External (cmsis-dap, esp-bridge, esp-prog, iot-bus-jtag, jlink, minimodule, olimex-arm-usb-ocd, olimex-arm-usb-ocd-h, olimex-arm-usb-tiny-h, olimex-jtag-tiny, tumpa)
PACKAGES: 
 - framework-arduinoespressif32 @ 2.0.14+sha.44da992 
 - tool-esptoolpy @ 1.40501.0 (4.5.1) 
 - tool-mkfatfs @ 2.0.1 
 - tool-mklittlefs @ 1.203.210628 (2.3) 
 - tool-mkspiffs @ 2.230.0 (2.30) 
 - toolchain-xtensa-esp32 @ 8.4.0+2021r2-patch5
LDF: Library Dependency Finder -> https://bit.ly/configure-pio-ldf
LDF Modes: Finder ~ chain, Compatibility ~ soft
Found 42 compatible libraries
Scanning dependencies...
Dependency Graph
|-- FastAccelStepper @ 0.30.15
|-- ESP32Ping @ 1.7.0
|-- AsyncTCP @ 1.1.1
|-- ESP32Encoder @ 0.11.7
|-- WiFi @ 2.0.0
|-- ArduinoNvs @ 2.8.0
|-- ESP32Console @ 1.2.2
|-- ArduinoOTA @ 2.0.0
|-- Ethernet @ 2.0.0
|-- Ticker @ 2.0.0
|-- ESP32 Async UDP @ 2.0.0
Building in release mode
Retrieving maximum program size .pio/build/esp32-rmii-ethernet/firmware.elf
Checking size .pio/build/esp32-rmii-ethernet/firmware.elf
Advanced Memory Usage is available via "PlatformIO Home > Project Inspect"
RAM:   [==        ]  19.1% (used 62484 bytes from 327680 bytes)
Flash: [========= ]  86.9% (used 1139529 bytes from 1310720 bytes)
Configuring upload protocol...
AVAILABLE: cmsis-dap, esp-bridge, esp-prog, espota, esptool, iot-bus-jtag, jlink, minimodule, olimex-arm-usb-ocd, olimex-arm-usb-ocd-h, olimex-arm-usb-tiny-h, olimex-jtag-tiny, tumpa
CURRENT: upload_protocol = esptool
Looking for upload port...
Using manually specified: /dev/ttyACM0
Uploading .pio/build/esp32-rmii-ethernet/firmware.bin
esptool.py v4.5.1
Serial port /dev/ttyACM0
Connecting...

A fatal error occurred: This chip is ESP32-S2 not ESP32. Wrong --chip argument?
*** [upload] Error 2
================================================= [FAILED] Took 8.35 seconds =================================================

Environment          Status    Duration
-------------------  --------  ------------
esp32-rmii-ethernet  FAILED    00:00:08.350
============================================ 1 failed, 0 succeeded in 00:00:08.350 ============================================

 *  The terminal process "platformio 'run', '--target', 'upload', '--environment', 'esp32-rmii-ethernet', '--upload-port', '/dev/ttyACM0'" terminated with exit code: 1. 
 *  Terminal will be reused by tasks, press any key to close it.