# this section is only required if using the sim testing panel # [APPLICATIONS] # DELAY = 3 # APP = test/plasmac_test.py # required [PLASMAC] # required for upgrades (DO NOT CHANGE) LAST_MAJOR_UPGRADE = 0.144 DBOUNCE = 1 # sets the operating mode, if not specified the default is 0 # 0 = use arc-voltage-in for arcOK and THC (no need to connect arc-ok-in, move-up-in and move-down-in) # 1 = use arc-ok-in for arcOK and arc-voltage-in for THC (no need to connect move-up-in and move-down-in) # 2 = use arc-ok-in for arcOK and move-down-in + move-up-in for THC (no need to connect arc-voltage-in) MODE = 2 # enable(0) or disable(1) the PlasmaC config page, if not specified the default is enabled CONFIG_DISABLE = 0 # the font for the Axis GUI, if not specified 'sans 10' will be used # valid font sizes are from 9 to 15 FONT = sans 10 # the window size for the Axis GUI # 0 = minimum size to suit font # 1 = maximized # width x height = custom size WINDOW_SIZE = 0 # the theme for the Axis GUI tabs, if not specified the system theme will be used THEME = Clearlooks # select portrait mode, if not specified the default is landscape #AXIS_ORIENT = portrait # percentage of cut-feed-rate used for paused motion speed PAUSED_MOTION_SPEED = 50 # torch on time when manual pulse requested TORCH_PULSE_TIME = 1.0 # for Powermax communications #PM_PORT = /dev/ttyUSB0 # for the five user buttons in the main window BUTTON_1_NAME = Ohmic\Test BUTTON_1_CODE = ohmic-test BUTTON_2_NAME = Probe\Test BUTTON_2_CODE = probe-test 30 BUTTON_3_NAME = Change\Consumables BUTTON_3_CODE = change-consumables X0 Y0 F4000 BUTTON_4_NAME = Pierce\& Cut BUTTON_4_CODE = cut-type BUTTON_5_NAME = Load\Sheet BUTTON_5_CODE = G53 G0 X{JOINT_0 HOME} Y1 # for the ten user buttons in the Extras panel BUTTON_10_NAME = BUTTON_10_CODE = BUTTON_10_IMAGE = BUTTON_11_NAME = BUTTON_11_CODE = BUTTON_11_IMAGE = BUTTON_12_NAME = BUTTON_12_CODE = BUTTON_12_IMAGE = BUTTON_13_NAME = BUTTON_13_CODE = BUTTON_13_IMAGE = BUTTON_14_NAME = PlasmaC\User Guide BUTTON_14_CODE = %xdg-open http://linuxcnc.org/docs/devel/html/plasma/plasmac-user-guide.html BUTTON_14_IMAGE = BUTTON_15_NAME = BUTTON_15_CODE = BUTTON_15_IMAGE = BUTTON_16_NAME = BUTTON_16_CODE = BUTTON_16_IMAGE = BUTTON_17_NAME = BUTTON_17_CODE = BUTTON_17_IMAGE = BUTTON_18_NAME = BUTTON_18_CODE = BUTTON_18_IMAGE = BUTTON_19_NAME = LinuxCNC\Docs BUTTON_19_CODE = %xdg-open http://linuxcnc.org/docs/devel/html BUTTON_19_IMAGE = # this section required as is for removing z axis moves from the loaded gcode file # this is optional and if used then plasmac_gcode.py needs to be set as executable [FILTER] PROGRAM_EXTENSION = .ngc (filter gcode files) ngc = ./plasmac/plasmac_gcode.py nc = ./plasmac/plasmac_gcode.py tap = ./plasmac/plasmac_gcode.py [RS274NGC] RS274NGC_STARTUP_CODE = o call PARAMETER_FILE = metric_parameters.txt # required, ./ must be in this path SUBROUTINE_PATH = ./:./plasmac:../../nc_files/subroutines # required for reading ini and hal variables FEATURES = 12 # required for our material change USER_M_PATH = ./:./plasmac [HAL] # required TWOPASS = ON # the base machine HALFILE = orangepi.hal # the plasmac component connections HALFILE = ./plasmac/plasmac.tcl # the plasma machine and custom connections HALFILE = orangepi_connections.hal # use this for customisation after GUI has loaded POSTGUI_HALFILE = postgui.tcl # required HALUI = halui [DISPLAY] DISPLAY = axis EDITOR = gedit POSITION_OFFSET = RELATIVE POSITION_FEEDBACK = ACTUAL ARCDIVISION = 64 GRIDS = 10mm 20mm 50mm 100mm 1in 2in 5in 10in MAX_FEED_OVERRIDE = 2.0 MIN_SPINDLE_OVERRIDE = 0.5 MAX_SPINDLE_OVERRIDE = 2.0 DEFAULT_LINEAR_VELOCITY = 5.00 MIN_LINEAR_VELOCITY = 0 MAX_LINEAR_VELOCITY = 100.00 INTRO_GRAPHIC = linuxcnc.gif INTRO_TIME = 2 PROGRAM_PREFIX = /home/user/linuxcnc/nc_files INCREMENTS = 5mm 1mm .5mm .1mm .05mm .01mm .005mm TOOL_EDITOR = tooledit x y CYCLE_TIME = 0.1 OPEN_FILE = "" # required USER_COMMAND_FILE = ./plasmac/plasmac_axis.py # required EMBED_TAB_NAME = Statistics EMBED_TAB_COMMAND = gladevcp -c plasmac_stats -x {XID} -u ./plasmac/plasmac_stats.py -H ./plasmac/plasmac_stats.hal ./plasmac/plasmac_stats.glade # use one of the next two # run panel in tab behind preview EMBED_TAB_NAME = Run EMBED_TAB_COMMAND = gladevcp -c plasmac_run -x {XID} -u ./plasmac/plasmac_run.py -H ./plasmac/plasmac_run.hal ./plasmac/plasmac_run_tab.glade # run panel in panel on right side #GLADEVCP = -c plasmac_run -u ./plasmac/plasmac_run.py -H ./plasmac/plasmac_run.hal ./plasmac/plasmac_run_panel.glade EMBED_TAB_NAME = Config EMBED_TAB_COMMAND = gladevcp -c plasmac_config -x {XID} -u ./plasmac/plasmac_config.py -H ./plasmac/plasmac_config.hal ./plasmac/plasmac_config.glade EMBED_TAB_NAME = Extras EMBED_TAB_COMMAND = gladevcp -c plasmac_wizards -x {XID} -u ./plasmac/plasmac_wizards.py ./plasmac/plasmac_wizards.glade [EMC] MACHINE = OrangePi DEBUG = 0 VERSION = 1.1 [KINS] JOINTS = 3 KINEMATICS = trivkins coordinates=XYZ [TASK] TASK = milltask CYCLE_TIME = 0.010 [EMCMOT] EMCMOT = motmod COMM_TIMEOUT = 1.0 BASE_PERIOD = 200000 SERVO_PERIOD = 1000000 [TRAJ] SPINDLES = 3 COORDINATES = X Y Z LINEAR_UNITS = mm ANGULAR_UNITS = degree DEFAULT_LINEAR_VELOCITY = 5.0 MAX_LINEAR_VELOCITY = 100.00 [EMCIO] EMCIO = io CYCLE_TIME = 0.100 TOOL_TABLE = tool.tbl [AXIS_X] # set to double the value in the corresponding joint MAX_VELOCITY = 200.0 # set to double the value in the corresponding joint MAX_ACCELERATION = 400.0 # shares the above two equally between the joint and the offset OFFSET_AV_RATIO = 0.5 MIN_LIMIT = -9999.0 MAX_LIMIT = 9999.0 [JOINT_0] TYPE = LINEAR HOME = 0.0 MIN_LIMIT = -9999.0 MAX_LIMIT = 9999.0 MAX_VELOCITY = 100.0 MAX_ACCELERATION = 200.0 SCALE = 1000.0 FERROR = 1 MIN_FERROR = 0.25 HOME_OFFSET = 0.0 [AXIS_Y] # set to double the value in the corresponding joint MAX_VELOCITY = 200.0 # set to double the value in the corresponding joint MAX_ACCELERATION = 400.0 # shares the above two equally between the joint and the offset OFFSET_AV_RATIO = 0.5 MIN_LIMIT = -9999.0 MAX_LIMIT = 9999.0 [JOINT_1] TYPE = LINEAR HOME = 0.0 MIN_LIMIT = -9999.0 MAX_LIMIT = 9999.0 MAX_VELOCITY = 100.0 MAX_ACCELERATION = 200.0 SCALE = 1000.0 FERROR = 1 MIN_FERROR = 0.25 HOME_OFFSET = 0.0 [AXIS_Z] # set to double the value in the corresponding joint MAX_VELOCITY = 200.0 # set to double the value in the corresponding joint MAX_ACCELERATION = 400.0 # shares the above two equally between the joint and the offset OFFSET_AV_RATIO = 0.5 MIN_LIMIT = -9999.0 MAX_LIMIT = 9999.0 [JOINT_2] TYPE = LINEAR HOME = 0.0 MIN_LIMIT = -9999.0 MAX_LIMIT = 9999.0 MAX_VELOCITY = 100.0 MAX_ACCELERATION = 200.0 SCALE = 1000.0 FERROR = 1 MIN_FERROR = 0.25 HOME_OFFSET = 0.0