o<1_2hlrect206> sub





( THIS WILL MAKE 1 RECTANGLE WITH 2x1.5" HOLES )


#<1LRcd>= 00                    ( enter left&right code for rectangle 1  way right )

#<1hght>= #<_generalheight>     ( enter height for rectangle 1 )
#<1wdth>= 43.5                    ( enter width for rectangle  1 )
#<startpoint>= 1               ( absolute Y&A point where wire will start cutting )

#<cutspeed>=  #<_generalspeed>                           
#<lspace>=    #<_generalspace>
#<wr>=0.0625                        


            ( DON'T MODIFY ANY NUMBERS BELOW THIS LINE )




#<1Lflng>=0
#<1Lflngdp>=0
#<1Rflng>=0
#<1Rflngdp>=0

#<1out>= 0
#<1Lcrn>=0
#<1Rcrn>=0




o101 if [#<1LRcd> EQ 77]
#<1Lflng>= 1.25
#<1Lflngdp>= 0.375
#<1Rflng>=1.25
#<1Rflngdp>=0.375
#<1out>=[#<1Rflngdp>+.25]
#<1Lcrn>=.25
#<1Rcrn>=.25

o101 elseif [#<1LRcd> EQ 74]
#<1Lflng>= 1.25
#<1Lflngdp>=0.375
#<1Rflng>=2.25
#<1Rflngdp>=.5625
#<1out>=#<1Rflngdp>
#<1Lcrn>=.25
#<1Rcrn>=0

o101 elseif [#<1LRcd> EQ 47]
#<1Lflng>= 2.25
#<1Lflngdp>= .5625
#<1Rflng>=1.25
#<1Rflngdp>=0.375
#<1out>=#<1Rflngdp>
#<1Lcrn>=0
#<1Rcrn>=.25

o101 elseif [#<1LRcd> EQ 04]
#<1Lflng>= 0
#<1Lflngdp>=0
#<1Rflng>=2.25
#<1Rflngdp>=0.5625
#<1out>=#<1Rflngdp>

o101 elseif [#<1LRcd> EQ 40]
#<1Lflng>= 2.25
#<1Lflngdp>=0.5625
#<1Rflng>=0
#<1Rflngdp>=0
#<1out>=#<1Rflngdp>

o101 elseif [#<1LRcd> EQ 00]
#<1Lflng>= 0
#<1Lflngdp>=0
#<1Rflng>=0
#<1Rflngdp>=0
#<1out>=#<1Rflngdp>

o101 endif                                  ( endif 1 )

   
G90
G4  P2
G1 Y #<startpoint>                       A  #<startpoint>    f #<cutspeed>
g1 X 0  Z  0
G91

g1 x- #<lspace>   Z- #<lspace>    
g1 y [#<1hght>-#<1Rflngdp>+#<wr>-#<1Rcrn>]             a [#<1hght>-#<1Rflngdp>+#<wr>-#<1Rcrn>]
g1 x-#<1Rcrn>   z-#<1Rcrn>   y#<1Rcrn>   a#<1Rcrn>     
g1  x- [#<1Rflng>-#<1Rcrn>]                            z- [#<1Rflng>-#<1Rcrn>] 
g1  y #<1Rflngdp>                                      a  #<1Rflngdp>
g1  x- [#<1wdth>-#<1Rflng>-#<1Lflng>+#<wr>]                  z- [#<1wdth>-#<1Rflng>-#<1Lflng>+#<wr>]
g1  y- #<1Lflngdp>          a- #<1Lflngdp>
g1  x- [#<1Lflng>-#<1Lcrn>]      z- [#<1Lflng>-#<1Lcrn>]
g1  x-#<1Lcrn>  z-#<1Lcrn> y-#<1Lcrn> a-#<1Lcrn>
g1  y- [#<1hght>-[#<1Lflngdp>*2]+#<wr>-[#<1Lcrn>*2]] a- [#<1hght>-[#<1Lflngdp>*2]+#<wr>-[#<1Lcrn>*2]] 
g1  x #<1Lcrn> z#<1Lcrn>  y-#<1Lcrn> a-#<1Lcrn>
g1  x [#<1Lflng>-#<1Lcrn>]       z [#<1Lflng>-#<1Lcrn>]
g1  y- #<1Lflngdp>                                     a- #<1Lflngdp>

G1 X [[#<1wdth>/4]+[#<wr>/2]-#<1Lflng>]                            Z [[#<1wdth>/4]+[#<wr>/2]-#<1Lflng>]                            
g1  y [#<1hght>/2-0.71875]                             A [#<1hght>/2-0.71875]
g1 x.11735                Z .11735  
g1 x .2232    Y .0725     Z .2232     A .0725
g1 x .1898    y .1379     Z .1898     A .1379
g1 x.1379     y.1898      Z .1379     A .1898
g1 x .0725    y .2232     Z .0725     A .2232
g1 y .2347    A .2347
g1 x- .0725   y .2232     Z- .0725    A .2232
g1 x- .1379   y .1898     Z- .1379    A .1898
g1 x- .1898   y .1379     Z- .1898    A .1379
g1 x- .2232   y .0725     Z- .2232    A .0725   
g1 x- .2347   Z-  .2347
g1 x- .2232   y-  .0725   Z- .2232    A- .0725
g1 x- .1898   y-  .1379   Z- .1898    A- .1379
g1 x- .1379   y-  .1898   Z- .1379    A- .1898
g1 x- .0725   y-  .2232   Z- .0725    A- .2232
g1 y- .2347   A-  .2347
g1 x .0725    y-  .2232   Z .0725     A- .2232
g1 x .1379    Y-  .1898   Z .1379     A- .1898
g1 x .1898    y-  .1379   Z .1898     A- .1379
g1 x .2232    y-  .0725   Z .2232     A- .0725
g1 x .11735   Z .11735
g1 y-  [#<1hght>/2-0.71875] A-  [#<1hght>/2-0.71875]
 G1 X [#<1wdth>/4*2]                        Z  [#<1wdth>/4*2]                            
g1  y [#<1hght>/2-0.71875]                             A [#<1hght>/2-0.71875]
g1 x.11735  Z .11735  
g1 x .2232  Y .0725   Z .2232   A .0725
g1 x .1898  y .1379   Z .1898   A .1379
g1 x.1379   y.1898   Z .1379   A .1898
g1 x .0725  y .2232   Z .0725   A .2232
g1 y .2347  A .2347
g1 x- .0725   y .2232   Z- .0725    A .2232
g1 x- .1379   y .1898   Z- .1379    A .1898
g1 x- .1898   y .1379   Z- .1898    A .1379
g1 x- .2232   y .0725   Z- .2232    A .0725   
g1 x- .2347   Z-  .2347
g1 x- .2232   y-  .0725   Z- .2232    A- .0725
g1 x- .1898   y-  .1379   Z- .1898    A- .1379
g1 x- .1379   y-  .1898   Z- .1379    A- .1898
g1 x- .0725   y-  .2232   Z- .0725    A- .2232
g1 y- .2347   A-  .2347
g1 x .0725  y-  .2232   Z .0725   A- .2232
g1 x .1379  Y-  .1898   Z .1379   A- .1898
g1 x .1898  y-  .1379   Z .1898   A- .1379
g1 x .2232  y-  .0725   Z .2232   A- .0725
g1 x .11735 Z .11735
g1  y- [#<1hght>/2-0.71875]               A- [#<1hght>/2-0.71875]
G1 X [[#<1wdth>/4]+[#<wr>/2]-#<1Rflng>]                        Z  [[#<1wdth>/4]+[#<wr>/2]-#<1Rflng>]                            
g1  y  #<1Rflngdp>                                      a #<1Rflngdp>
g1  x [#<1Rflng>-#<1Rcrn>]                              z [#<1Rflng>-#<1Rcrn>]
g1 x#<1Rcrn>   z#<1Rcrn>   y#<1Rcrn>   a#<1Rcrn>



G90 
G1 X 0.25 Z 0.25          

o<1_2hlrect206> endsub
m2