# Generated by PNCconf at Sat May 16 14:12:34 2026
# Using LinuxCNC version:  Master (2.9)
# If you make changes to this file, they will be
# overwritten when you run PNCconf again

[EMC]
MACHINE = my_LinuxCNC_machine
DEBUG = 0
VERSION = 1.1

[DISPLAY]
DISPLAY = qtvcp qtplasmac
POSITION_OFFSET = RELATIVE
POSITION_FEEDBACK = ACTUAL
MAX_FEED_OVERRIDE = 2.000000
INTRO_GRAPHIC = linuxcnc.gif
INTRO_TIME = 5
PROGRAM_PREFIX = /home/rolando/linuxcnc/nc_files
INCREMENTS = 1in .1in .01in .001in .0001in
POSITION_FEEDBACK = ACTUAL
DEFAULT_LINEAR_VELOCITY = 0.250000
MAX_LINEAR_VELOCITY = 1.000000
MIN_LINEAR_VELOCITY = 0.016670
DEFAULT_ANGULAR_VELOCITY = 12.000000
MAX_ANGULAR_VELOCITY = 180.000000
MIN_ANGULAR_VELOCITY = 1.666667
GEOMETRY = xyz
CYCLE_TIME = 100

[FILTER]
PROGRAM_EXTENSION = .ngc,.nc,.tap GCode File (*.ngc, *.nc, *.tap)
ngc = qtplasmac_gcode
nc  = qtplasmac_gcode
tap = qtplasmac_gcode

[TASK]
TASK = milltask
CYCLE_TIME = 0.010

[RS274NGC]
PARAMETER_FILE = linuxcnc.var
RS274NGC_STARTUP_CODE = G20 G40 G49 G80 G90 G92.1 G94 G97 M52P1
SUBROUTINE_PATH = ./:../../nc_files
USER_M_PATH = ./:../../nc_files


[EMCMOT]
EMCMOT = motmod
COMM_TIMEOUT = 1.0
SERVO_PERIOD = 1000000

[HMOT]
# **** This is for info only ****
CARD0=hm2_7i76e.0

[HAL]
HALUI = halui
HALFILE = my_LinuxCNC_machine.hal
HALFILE = qtplasmac_comp.hal
HALFILE = custom.hal
POSTGUI_HALFILE = custom_postgui.hal
SHUTDOWN = shutdown.hal

[HALUI]

[KINS]
JOINTS = 4
KINEMATICS = trivkins coordinates=XYYZ

[TRAJ]
SPINDLES = 3
COORDINATES =  XYYZ
LINEAR_UNITS = inch
ANGULAR_UNITS = degree
DEFAULT_LINEAR_VELOCITY = 1.00
MAX_LINEAR_VELOCITY = 10.00

[EMCIO]
EMCIO = io
CYCLE_TIME = 0.100
TOOL_TABLE = tool.tbl

#******************************************
[AXIS_X]
# MAX_VEL & MAX_ACC need to be twice the corresponding joint value
MAX_VELOCITY = 20.0
MAX_ACCELERATION = 60.0
OFFSET_AV_RATIO = 0.5
MIN_LIMIT = -0.0
MAX_LIMIT = 60.5

[JOINT_0]
TYPE = LINEAR
HOME = 0.25
FERROR = 0.5
MIN_FERROR = 0.05
MAX_VELOCITY = 10.0
MAX_ACCELERATION = 30.0
# The values below should be 25% larger than MAX_VELOCITY and MAX_ACCELERATION
# If using BACKLASH compensation STEPGEN_MAXACCEL should be 100% larger.
STEPGEN_MAXVEL = 12.50
STEPGEN_MAXACCEL = 37.50
P = 1000.0
I = 0.0
D = 0.0
FF0 = 0.0
FF1 = 1.0
FF2 = 0.0
BIAS = 0.0
DEADBAND = 0.0
MAX_OUTPUT = 0.0
# these are in nanoseconds
DIRSETUP   = 10000
DIRHOLD    = 10000
STEPLEN    = 5000
STEPSPACE  = 5000
STEP_SCALE = 2152.0
MIN_LIMIT = -0.0
MAX_LIMIT = 60.5
HOME_OFFSET = 0.000000
HOME_SEARCH_VEL = -0.500000
HOME_LATCH_VEL = -0.083333
HOME_FINAL_VEL = 0.000000
HOME_USE_INDEX = NO
HOME_IGNORE_LIMITS = YES
HOME_SEQUENCE = 2
#******************************************

#******************************************
[AXIS_Y]
# MAX_VEL & MAX_ACC need to be twice the corresponding joint value
MAX_VELOCITY = 20.0
MAX_ACCELERATION = 60.0
OFFSET_AV_RATIO = 0.5
MIN_LIMIT = -0.0
MAX_LIMIT = 120.5

[JOINT_1]
TYPE = LINEAR
HOME = 0.25
FERROR = 0.5
MIN_FERROR = 0.05
MAX_VELOCITY = 10.0
MAX_ACCELERATION = 30.0
# The values below should be 25% larger than MAX_VELOCITY and MAX_ACCELERATION
# If using BACKLASH compensation STEPGEN_MAXACCEL should be 100% larger.
STEPGEN_MAXVEL = 12.50
STEPGEN_MAXACCEL = 37.50
P = 1000.0
I = 0.0
D = 0.0
FF0 = 0.0
FF1 = 1.0
FF2 = 0.0
BIAS = 0.0
DEADBAND = 0.0
MAX_OUTPUT = 0.0
# these are in nanoseconds
DIRSETUP   = 10000
DIRHOLD    = 10000
STEPLEN    = 5000
STEPSPACE  = 5000
STEP_SCALE = -2152.0
MIN_LIMIT = -0.0
MAX_LIMIT = 120.5
HOME_OFFSET = 0.000000
HOME_SEARCH_VEL = -0.500000
HOME_LATCH_VEL = -0.083333
HOME_FINAL_VEL = 0.000000
HOME_USE_INDEX = NO
HOME_IGNORE_LIMITS = YES
HOME_SEQUENCE = -3

[JOINT_2]
TYPE = LINEAR
HOME = 0.25
FERROR = 0.5
MIN_FERROR = 0.05
MAX_VELOCITY = 10.0
MAX_ACCELERATION = 30.0
# The values below should be 25% larger than MAX_VELOCITY and MAX_ACCELERATION
# If using BACKLASH compensation STEPGEN_MAXACCEL should be 100% larger.
STEPGEN_MAXVEL = 12.50
STEPGEN_MAXACCEL = 37.50
P = 1000.0
I = 0.0
D = 0.0
FF0 = 0.0
FF1 = 1.0
FF2 = 0.0
BIAS = 0.0
DEADBAND = 0.0
MAX_OUTPUT = 0.0
# these are in nanoseconds
DIRSETUP   = 10000
DIRHOLD    = 10000
STEPLEN    = 5000
STEPSPACE  = 5000
STEP_SCALE = 2152.0
MIN_LIMIT = -0.0
MAX_LIMIT = 120.5
HOME_OFFSET = 0.000000
HOME_SEARCH_VEL = -0.500000
HOME_LATCH_VEL = -0.083333
HOME_FINAL_VEL = 0.000000
HOME_USE_INDEX = NO
HOME_IGNORE_LIMITS = YES
HOME_SEQUENCE = -3
#******************************************

#******************************************
[AXIS_Z]
# MAX_VEL & MAX_ACC need to be twice the corresponding joint value
MAX_VELOCITY = 6.666666666666667
MAX_ACCELERATION = 60.0
OFFSET_AV_RATIO = 0.5
MIN_LIMIT = -8.0
MAX_LIMIT = 8.0

[JOINT_3]
TYPE = LINEAR
HOME = -0.25
FERROR = 0.5
MIN_FERROR = 0.05
MAX_VELOCITY = 3.3333333333333335
MAX_ACCELERATION = 30.0
# The values below should be 25% larger than MAX_VELOCITY and MAX_ACCELERATION
# If using BACKLASH compensation STEPGEN_MAXACCEL should be 100% larger.
STEPGEN_MAXVEL = 4.17
STEPGEN_MAXACCEL = 37.50
P = 1000.0
I = 0.0
D = 0.0
FF0 = 0.0
FF1 = 1.0
FF2 = 0.0
BIAS = 0.0
DEADBAND = 0.0
MAX_OUTPUT = 0.0
# these are in nanoseconds
DIRSETUP   = 10000
DIRHOLD    = 10000
STEPLEN    = 5000
STEPSPACE  = 5000
STEP_SCALE = 4000.0
MIN_LIMIT = -8.0
MAX_LIMIT = 8.0
HOME_OFFSET = 0.000000
HOME_SEARCH_VEL = 0.500000
HOME_LATCH_VEL = 0.083333
HOME_FINAL_VEL = 0.000000
HOME_USE_INDEX = NO
HOME_IGNORE_LIMITS = YES
HOME_SEQUENCE = 1
#******************************************