swanie@3040CNC:~$ linuxcnc LINUXCNC - 2.9.0~pre1+git20230208.f1270d6ed7 Machine configuration directory is '/home/swanie/linuxcnc/configs/3040_CNC_V3' Machine configuration file is '3040_CNC_V3.ini' Starting LinuxCNC... linuxcnc TPMOD=tpmod HOMEMOD=homemod EMCMOT=motmod Note: Using POSIX realtime Found file(REL): ./3040_CNC_V3.hal hm2: loading Mesa HostMot2 driver version 0.15 hm2_eth: loading Mesa AnyIO HostMot2 ethernet driver version 0.2 hm2_eth: 10.10.10.10: INFO: Hardware address (MAC): 00:60:1b:10:44:e2 hm2_eth: discovered 7I76E-16 hm2/hm2_7i76e.0: Low Level init 0.15 hm2/hm2_7i76e.0: Smart Serial Firmware Version 43 Board hm2_7i76e.0.7i76.0.0 Hardware Mode 0 = standard Board hm2_7i76e.0.7i76.0.0 Software Mode 0 = io_spin Board hm2_7i76e.0.7i76.0.0 Software Mode 1 = io_ana_spin Board hm2_7i76e.0.7i76.0.0 Software Mode 2 = io_enc_ana_spin_fv hm2/hm2_7i76e.0: 51 I/O Pins used: hm2/hm2_7i76e.0: IO Pin 000 (P1-01): StepGen #0, pin Direction (Output) hm2/hm2_7i76e.0: IO Pin 001 (P1-14): StepGen #0, pin Step (Output) hm2/hm2_7i76e.0: IO Pin 002 (P1-02): StepGen #1, pin Direction (Output) hm2/hm2_7i76e.0: IO Pin 003 (P1-15): StepGen #1, pin Step (Output) hm2/hm2_7i76e.0: IO Pin 004 (P1-03): StepGen #2, pin Direction (Output) hm2/hm2_7i76e.0: IO Pin 005 (P1-16): StepGen #2, pin Step (Output) hm2/hm2_7i76e.0: IO Pin 006 (P1-04): StepGen #3, pin Direction (Output) hm2/hm2_7i76e.0: IO Pin 007 (P1-17): StepGen #3, pin Step (Output) hm2/hm2_7i76e.0: IO Pin 008 (P1-05): StepGen #4, pin Direction (Output) hm2/hm2_7i76e.0: IO Pin 009 (P1-06): StepGen #4, pin Step (Output) hm2/hm2_7i76e.0: IO Pin 010 (P1-07): Smart Serial Interface #0, pin tx0 (Output) hm2/hm2_7i76e.0: IO Pin 011 (P1-08): Smart Serial Interface #0, pin rx0 (Input) hm2/hm2_7i76e.0: IO Pin 012 (P1-09): IOPort hm2/hm2_7i76e.0: IO Pin 013 (P1-10): IOPort hm2/hm2_7i76e.0: IO Pin 014 (P1-11): Encoder #0, pin Index (Input) hm2/hm2_7i76e.0: IO Pin 015 (P1-12): Encoder #0, pin B (Input) hm2/hm2_7i76e.0: IO Pin 016 (P1-13): Encoder #0, pin A (Input) hm2/hm2_7i76e.0: IO Pin 017 (P2-01): IOPort hm2/hm2_7i76e.0: IO Pin 018 (P2-14): IOPort hm2/hm2_7i76e.0: IO Pin 019 (P2-02): IOPort hm2/hm2_7i76e.0: IO Pin 020 (P2-15): IOPort hm2/hm2_7i76e.0: IO Pin 021 (P2-03): IOPort hm2/hm2_7i76e.0: IO Pin 022 (P2-16): IOPort hm2/hm2_7i76e.0: IO Pin 023 (P2-04): IOPort hm2/hm2_7i76e.0: IO Pin 024 (P2-17): IOPort hm2/hm2_7i76e.0: IO Pin 025 (P2-05): IOPort hm2/hm2_7i76e.0: IO Pin 026 (P2-06): IOPort hm2/hm2_7i76e.0: IO Pin 027 (P2-07): IOPort hm2/hm2_7i76e.0: IO Pin 028 (P2-08): IOPort hm2/hm2_7i76e.0: IO Pin 029 (P2-09): IOPort hm2/hm2_7i76e.0: IO Pin 030 (P2-10): IOPort hm2/hm2_7i76e.0: IO Pin 031 (P2-11): IOPort hm2/hm2_7i76e.0: IO Pin 032 (P2-12): IOPort hm2/hm2_7i76e.0: IO Pin 033 (P2-13): IOPort hm2/hm2_7i76e.0: IO Pin 034 (P3-01): IOPort hm2/hm2_7i76e.0: IO Pin 035 (P3-14): IOPort hm2/hm2_7i76e.0: IO Pin 036 (P3-02): IOPort hm2/hm2_7i76e.0: IO Pin 037 (P3-15): IOPort hm2/hm2_7i76e.0: IO Pin 038 (P3-03): IOPort hm2/hm2_7i76e.0: IO Pin 039 (P3-16): IOPort hm2/hm2_7i76e.0: IO Pin 040 (P3-04): IOPort hm2/hm2_7i76e.0: IO Pin 041 (P3-17): IOPort hm2/hm2_7i76e.0: IO Pin 042 (P3-05): IOPort hm2/hm2_7i76e.0: IO Pin 043 (P3-06): IOPort hm2/hm2_7i76e.0: IO Pin 044 (P3-07): IOPort hm2/hm2_7i76e.0: IO Pin 045 (P3-08): IOPort hm2/hm2_7i76e.0: IO Pin 046 (P3-09): IOPort hm2/hm2_7i76e.0: IO Pin 047 (P3-10): IOPort hm2/hm2_7i76e.0: IO Pin 048 (P3-11): IOPort hm2/hm2_7i76e.0: IO Pin 049 (P3-12): IOPort hm2/hm2_7i76e.0: IO Pin 050 (P3-13): IOPort hm2/hm2_7i76e.0: registered creating ladder-state Found file(REL): ./custom.hal INFO CLASSICLADDER- No ladder GUI requested-Realtime runs till HAL closes. [DEFAULT][INFO] Logging to: /home/swanie/default.log (logger.py:107) [DEFAULT.QTVCP.QT_ISTAT][DEBUG] Machine is METRIC based. unit Conversion constant=0.03937007874015748 (qt_istat.py:150) [DEFAULT.QTVCP.QT_ISTAT][DEBUG] TRAJ COORDINATES: XYZ (qt_istat.py:161) [DEFAULT.QTVCP.QT_ISTAT][DEBUG] DEFAULT_LINEAR_VELOCITY = 10000.00002 (qt_istat.py:341) [DEFAULT.QTVCP.QT_ISTAT][DEBUG] MIN_LINEAR_VELOCITY = 499.99998 (qt_istat.py:342) [DEFAULT.QTVCP.QT_ISTAT][DEBUG] MAX_LINEAR_VELOCITY = 2500.00002 (qt_istat.py:343) [DEFAULT.QTVCP.QT_ISTAT][WARNING] INI Parsing Error, No DEFAULT_SPINDLE_0_SPEED Entry in DISPLAY, Using: 200 (qt_istat.py:515) [DEFAULT.QTVCP.QT_ISTAT][WARNING] INI Parsing Error, No MIN_SPINDLE_0_SPEED Entry in DISPLAY, Using: 100 (qt_istat.py:515) [DEFAULT.QTVCP.QT_ISTAT][WARNING] INI Parsing Error, No MAX_SPINDLE_0_SPEED Entry in DISPLAY, Using: 2500 (qt_istat.py:515) [DEFAULT.QTVCP.QT_ISTAT][WARNING] INI Parsing Error, No MAX_SPINDLE_0_OVERRIDE Entry in DISPLAY, Using: 1 (qt_istat.py:515) [DEFAULT.QTVCP.QT_ISTAT][WARNING] INI Parsing Error, No MIN_SPINDLE_0_OVERRIDE Entry in DISPLAY, Using: 0.5 (qt_istat.py:515) not enough values to unpack (expected 2, got 1) 'btn_sel_next' 'btn_sel_prev' 'btn_select' 'btn_home' 'btn_dir_up' 'btn_jump_to' not enough values to unpack (expected 2, got 1) not enough values to unpack (expected 2, got 1) 'IconFileSelection' object has no attribute 'on_btn_jump_to' not enough values to unpack (expected 2, got 1) not enough values to unpack (expected 2, got 1) (gmoccapy:2525): Gtk-CRITICAL **: 16:43:16.693: gtk_entry_set_text: assertion 'text != NULL' failed Attribute error and sans 10 Attribute error and sans 10 0 = /usr/bin/gmoccapy 1 = -ini 2 = /home/swanie/linuxcnc/configs/3040_CNC_V3/3040_CNC_V3.ini Entry = trivkins Entry = coordinates=XYZ found the following coordinates xyz **** GMOCCAPY GETINIINFO **** Number of joints = 3 3 COORDINATES found = xyz joint 0 = axis x joint 1 = axis y joint 2 = axis z {0: 'x', 1: 'y', 2: 'z'} **** GMOCCAPY GETINIINFO **** [KINS] KINESTYPE is trivkins **** GMOCCAPY GETINIINFO **** No MAX_RAPID_OVERRIDE entry found in [DISPLAY] of INI file Default settings 100 % applied! **** GMOCCAPY GETINIINFO **** Preference file path: /home/swanie/linuxcnc/configs/3040_CNC_V3/3040_CNC_V3.pref **** GMOCCAPY GETINIINFO **** No DEFAULT_SPINDLE_SPEED entry found in [DISPLAY] of INI file **** GMOCCAPY INFO **** **** no valid probe config in INI File **** **** disabled tool measurement **** **** GMOCCAPY INFO **** **** Entering make_DRO axis_list = ['x', 'y', 'z'] **** GMOCCAPY INFO **** **** Entering make ref axis button **** GMOCCAPY INFO **** **** Entering make touch button /usr/bin/gmoccapy:1011: DeprecationWarning: Gtk.Widget.override_background_color is deprecated btn.override_background_color(Gtk.StateFlags.ACTIVE, Gdk.RGBA(1.0, 1.0, 0.0, 1.0)) **** GMOCCAPY INFO **** **** Entering make jog increments **** GMOCCAPY INFO **** **** Entering make jog button **** GMOCCAPY INFO **** **** Entering make macro button found 0 Macros **** GMOCCAPY INFO **** **** arrange DRO 3 **** GMOCCAPY INFO **** **** Place in table /usr/bin/gmoccapy:1620: DeprecationWarning: Gtk.Table.resize is deprecated self.widgets.tbl_DRO.resize(rows, cols) **** GMOCCAPY INFO **** **** get DRO order **** GMOCCAPY INFO **** **** arrange JOG button less than 6 axis Setting icon theme 'classic' [GladeVCP][INFO] Logging to: /home/swanie/gladevcp.log (logger.py:107) **** GMOCCAPY INFO **** **** no audio available! **** **** PYGST library not installed? **** **** is python-gstX.XX installed? **** **** GMOCCAPY INFO **** **** Entering init gremlin **** Kinematics type changed _set_enable_tooltips = True 'IconFileSelection' object has no attribute 'on_btn_jump_to' **** GMOCCAPY INFO **** **** virtual keyboard program found : [GladeVCP.QTVCP.QT_ISTAT][WARNING] INI Parsing Error, No DEFAULT_SPINDLE_0_SPEED Entry in DISPLAY, Using: 200 (qt_istat.py:515) [GladeVCP.QTVCP.QT_ISTAT][WARNING] INI Parsing Error, No MIN_SPINDLE_0_SPEED Entry in DISPLAY, Using: 100 (qt_istat.py:515) [GladeVCP.QTVCP.QT_ISTAT][WARNING] INI Parsing Error, No MAX_SPINDLE_0_SPEED Entry in DISPLAY, Using: 2500 (qt_istat.py:515) [GladeVCP.QTVCP.QT_ISTAT][WARNING] INI Parsing Error, No MAX_SPINDLE_0_OVERRIDE Entry in DISPLAY, Using: 1 (qt_istat.py:515) [GladeVCP.QTVCP.QT_ISTAT][WARNING] INI Parsing Error, No MIN_SPINDLE_0_OVERRIDE Entry in DISPLAY, Using: 0.5 (qt_istat.py:515) spindle_button.hal:17: Pin 'halui.spindle.increase' does not exist 'halcmd -f spindle_button.hal' exited with 1 /usr/lib/python3/dist-packages/Onboard/LayoutLoaderSVG.py:447: SyntaxWarning: 'str' object is not callable; perhaps you missed a comma? raise Exceptions.LayoutFileError("Unrecognized modifier %s in" \ /usr/bin/gmoccapy:3377: DeprecationWarning: Gtk.FontButton.get_font_name is deprecated self.notification.set_property('font', self.widgets.fontbutton_popup.get_font_name()) /usr/bin/gmoccapy:378: DeprecationWarning: Gtk.FontButton.set_font_name is deprecated self.widgets.fontbutton_popup.set_font_name(self.prefs.getpref("message_font", "sans 10", str)) /usr/bin/gmoccapy:473: DeprecationWarning: Gtk.ColorButton.set_color is deprecated self.widgets.abs_colorbutton.set_color(Gdk.color_parse(self.abs_color)) **** GMOCCAPY INFO : inifile = /home/swanie/linuxcnc/configs/3040_CNC_V3/3040_CNC_V3.ini ****: **** GMOCCAPY INFO : postgui halfile = ['gmoccapy_postgui.hal', 'custom_postgui.hal'] ****: Jog Pin Changed x+ Jog Button released = x+ Jog Pin Changed x- Jog Button released = x- Jog Pin Changed y+ Jog Button released = y+ Jog Pin Changed y- Jog Button released = y- Jog Pin Changed z+ Jog Button released = z+ Jog Pin Changed z- Jog Button released = z- on tool change