[   56.640763] hid-generic 0003:145F:0333.0001: input,hidraw0: USB HID v2.00 Keyboard [YICHIP Trust Yvi+Wireless Mouse] on usb-0000:00:1d.0-1.3/input0
[   56.641205] input: YICHIP Trust Yvi+Wireless Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.1/0003:145F:0333.0002/input/input21
[   56.641531] input: YICHIP Trust Yvi+Wireless Mouse System Control as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.1/0003:145F:0333.0002/input/input22
[   56.700666] input: YICHIP Trust Yvi+Wireless Mouse Consumer Control as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.1/0003:145F:0333.0002/input/input23
[   56.702379] hid-generic 0003:145F:0333.0002: input,hiddev0,hidraw1: USB HID v2.00 Mouse [YICHIP Trust Yvi+Wireless Mouse] on usb-0000:00:1d.0-1.3/input1
[  519.987480] EtherCAT: Requesting master 0...
[  519.987488] EtherCAT: Successfully requested master 0.
[  519.987549] EtherCAT ERROR 0 0:1: PDO entry 0x6000:01 is not mapped.
[  519.987645] EtherCAT 0: Releasing master...
[  519.987651] EtherCAT 0: Released.
[ 2822.956329] perf: interrupt took too long (2506 > 2500), lowering kernel.perf_event_max_sample_rate to 79750
[ 4612.058342] perf: interrupt took too long (3136 > 3132), lowering kernel.perf_event_max_sample_rate to 63750
[ 4702.448843] perf: interrupt took too long (3933 > 3920), lowering kernel.perf_event_max_sample_rate to 50750
[ 5562.345801] perf: interrupt took too long (4929 > 4916), lowering kernel.perf_event_max_sample_rate to 40500
[10640.849067] EtherCAT: Requesting master 0...
[10640.849075] EtherCAT: Successfully requested master 0.
[10640.849188] EtherCAT 0: Domain0: Logical address 0x00000000, 4 byte, expected working counter 3.
[10640.849191] EtherCAT 0:   Datagram domain0-0-main: Logical offset 0x00000000, 4 byte, type LRW.
[10640.849262] EtherCAT 0: Master thread exited.
[10640.849264] EtherCAT 0: Starting EtherCAT-OP thread.
[11062.866990] EtherCAT 0: Master thread exited.
[11062.867004] EtherCAT 0: Starting EtherCAT-IDLE thread.
[11062.867097] EtherCAT 0: Releasing master...
[11062.867099] EtherCAT 0: Released.
[11062.887921] EtherCAT WARNING: Datagram 000000008b6aead7 (master-fsm) was SKIPPED 1 time.
[11258.852499] wls1: deauthenticating from f6:9f:c2:f1:75:59 by local choice (Reason: 3=DEAUTH_LEAVING)
[11259.247139] wls1: authenticate with f6:9f:c2:f1:75:59
[11259.247167] wls1: 80 MHz not supported, disabling VHT
[11259.261471] wls1: send auth to f6:9f:c2:f1:75:59 (try 1/3)
[11259.266674] wls1: authenticated
[11259.267936] wls1: associate with f6:9f:c2:f1:75:59 (try 1/3)
[11259.274348] wls1: RX AssocResp from f6:9f:c2:f1:75:59 (capab=0x1431 status=0 aid=1)
[11259.274527] wls1: associated
[11259.274673] ath: EEPROM regdomain: 0x8268
[11259.274675] ath: EEPROM indicates we should expect a country code
[11259.274676] ath: doing EEPROM country->regdmn map search
[11259.274677] ath: country maps to regdmn code: 0x37
[11259.274678] ath: Country alpha2 being used: PL
[11259.274679] ath: Regpair used: 0x37
[11259.274680] ath: regdomain 0x8268 dynamically updated by country element
[11259.295030] wls1: Limiting TX power to 20 (20 - 0) dBm as advertised by f6:9f:c2:f1:75:59
[11259.340465] IPv6: ADDRCONF(NETDEV_CHANGE): wls1: link becomes ready
grzesiekzxr@grzesiekzxr:~/linuxcnc/configs/sim.axis$