;     file name: Nate OC Bracket marker1.ngc
; date and time: Sun Jun 07 2020    17:41:02
; postprocessor: PlasmaC_F.scpost rev: F
;
;begin pre-amble
 G20 (units: inches)
 G40 (cutter compensation: off)
 G90 (distance mode: absolute)
 M52 P1 (adaptive feed: on)
 M65 P2 (enable THC)
 M65 P3 (enable torch)
 M68 E3 Q0 (velocity 100%)
 G64 P0.005 Q0.001 (tracking tolerances: 0.005")
 F#<_hal[plasmac.cut-feed-rate]>
;end pre-amble
;
;begin material setup
 M190 P1 (20ga steel finecut lowspeed material)
 M66 P3 L3 Q2 (wait for valid change)
 F#<_hal[plasmac.cut-feed-rate]>
;end material setup
;
;begin nate oc bracket duplicate 1 #1, cutting, 2.94"
 G0 X11.99918 Y8.25295
 M3 $0 S1 (cut start)
 G1 X9.05918 Y8.25295
 M5 $0(cut stop)
;end nate oc bracket duplicate 1, cutting #1
;
;begin nate oc bracket duplicate 1 #2, cutting, 4.44"
 G0 X6.87168 Y7.34795
 M3 $0 S1 (cut start)
 G1 X6.87168 Y2.90795
 M5 $0(cut stop)
;end nate oc bracket duplicate 1, cutting #2
;
;begin nate oc bracket duplicate 1 #3, cutting, 0.94"
 G0 X3.81740 Y4.81689
 M3 $0 S1 (cut start)
 G1 X3.81740 Y3.87689
 M5 $0(cut stop)
;end nate oc bracket duplicate 1, cutting #3
;
;begin nate oc bracket duplicate 1 #4, cutting, 0.94"
 G0 X3.28740 Y4.81689
 M3 $0 S1 (cut start)
 G1 X3.28740 Y3.87689
 M5 $0(cut stop)
;end nate oc bracket duplicate 1, cutting #4
;
;begin nate oc bracket duplicate 1 #5, cutting, 1.60"
 G0 X1.16240 Y4.34689
 M3 $0 S1 (cut start)
 G1 X1.16240 Y4.14689
 G1 X1.16240 Y4.54689
 G1 X1.16240 Y4.34689
 G1 X1.36240 Y4.34689
 G1 X0.96240 Y4.34689
 G1 X1.16240 Y4.34689
 M5 $0(cut stop)
;end nate oc bracket duplicate 1, cutting #5
;
;begin nate oc bracket duplicate 1 #6, cutting, 4.44"
 G0 X4.71668 Y7.34795
 M3 $0 S1 (cut start)
 G1 X4.71668 Y2.90795
 M5 $0(cut stop)
;end nate oc bracket duplicate 1, cutting #6
;
;begin nate oc bracket duplicate 1 #7, cutting, 2.94"
 G0 X11.99918 Y2.00295
 M3 $0 S1 (cut start)
 G1 X9.05918 Y2.00295
 M5 $0(cut stop)
;end nate oc bracket duplicate 1, cutting #7
;
;begin nate oc bracket duplicate 1 #8, cutting, 4.44"
 G0 X14.18668 Y7.34795
 M3 $0 S1 (cut start)
 G1 X14.18668 Y2.90795
 M5 $0(cut stop)
;end nate oc bracket duplicate 1, cutting #8
;
;begin nate oc bracket duplicate 1 #9, cutting, 0.94"
 G0 X17.44240 Y3.06389
 M3 $0 S1 (cut start)
 G1 X17.44240 Y4.00389
 M5 $0(cut stop)
;end nate oc bracket duplicate 1, cutting #9
;
;begin nate oc bracket duplicate 1 #10, cutting, 0.94"
 G0 X17.97240 Y3.06389
 M3 $0 S1 (cut start)
 G1 X17.97240 Y4.00389
 M5 $0(cut stop)
;end nate oc bracket duplicate 1, cutting #10
;
;begin nate oc bracket duplicate 1 #11, cutting, 1.60"
 G0 X19.09740 Y3.53389
 M3 $0 S1 (cut start)
 G1 X18.89740 Y3.53389
 G1 X19.29740 Y3.53389
 G1 X19.09740 Y3.53389
 G1 X19.09740 Y3.33389
 G1 X19.09740 Y3.73389
 G1 X19.09740 Y3.53389
 M5 $0(cut stop)
;end nate oc bracket duplicate 1, cutting #11
;
;begin nate oc bracket duplicate 1 #12, cutting, 4.44"
 G0 X16.34168 Y7.34795
 M3 $0 S1 (cut start)
 G1 X16.34168 Y2.90795
 M5 $0(cut stop)
;end nate oc bracket duplicate 1, cutting #12
;
;begin nate oc bracket duplicate 1 #13, cutting, 0.94"
 G0 X17.44240 Y9.12589
 M3 $0 S1 (cut start)
 G1 X17.44240 Y10.06589
 M5 $0(cut stop)
;end nate oc bracket duplicate 1, cutting #13
;
;begin nate oc bracket duplicate 1 #14, cutting, 0.94"
 G0 X17.97240 Y9.12589
 M3 $0 S1 (cut start)
 G1 X17.97240 Y10.06589
 M5 $0(cut stop)
;end nate oc bracket duplicate 1, cutting #14
;
;begin nate oc bracket duplicate 1 #15, cutting, 1.60"
 G0 X19.09740 Y9.59589
 M3 $0 S1 (cut start)
 G1 X19.09740 Y9.39589
 G1 X19.09740 Y9.79589
 G1 X19.09740 Y9.59589
 G1 X18.89740 Y9.59589
 G1 X19.29740 Y9.59589
 G1 X19.09740 Y9.59589
 M5 $0(cut stop)
;end nate oc bracket duplicate 1, cutting #15
;
;begin nate oc bracket duplicate 1 #16, cutting, 59.28"
 G0 X19.43579 Y9.13250
 M3 $0 S1 (cut start)
 G3 X19.47240 Y9.22089 I-0.08839 J0.08839
 G1 X19.47240 Y9.97089
 G3 X19.34740 Y10.09589 I-0.12500 J-0.00000
 G1 X16.46668 Y10.09589
 G3 X16.34168 Y9.97089 I0.00000 J-0.12500
 G1 X16.34168 Y8.87795
 G1 X4.21668 Y8.87795
 G3 X4.09168 Y8.75295 I0.00000 J-0.12500
 G1 X4.09168 Y4.84689
 G1 X0.91240 Y4.84689
 G3 X0.78740 Y4.72189 I0.00000 J-0.12500
 G1 X0.78740 Y3.97189
 G3 X0.91240 Y3.84689 I0.12500 J0.00000
 G1 X4.09168 Y3.84689
 G1 X4.09168 Y1.50295
 G3 X4.21668 Y1.37795 I0.12500 J0.00000
 G1 X16.84168 Y1.37795
 G3 X16.96668 Y1.50295 I0.00000 J0.12500
 G1 X16.96668 Y3.03389
 G1 X19.34740 Y3.03389
 G3 X19.47240 Y3.15889 I0.00000 J0.12500
 G1 X19.47240 Y3.90889
 G3 X19.34740 Y4.03389 I-0.12500 J0.00000
 G1 X16.96668 Y4.03389
 G1 X16.96668 Y9.09589
 G1 X19.34740 Y9.09589
 G3 X19.43579 Y9.13250 I0.00000 J0.12500
 M5 $0(cut stop)
;end nate oc bracket, cutting #16
;
;begin nate oc bracket #17, cutting, 2.94"
 G0 X24.99290 Y3.22089
 M3 $0 S1 (cut start)
 G1 X27.93290 Y3.22089
 M5 $0(cut stop)
;end nate oc bracket, cutting #17
;
;begin nate oc bracket #18, cutting, 4.44"
 G0 X30.12040 Y4.12589
 M3 $0 S1 (cut start)
 G1 X30.12040 Y8.56589
 M5 $0(cut stop)
;end nate oc bracket, cutting #18
;
;begin nate oc bracket #19, cutting, 0.94"
 G0 X33.17469 Y6.65695
 M3 $0 S1 (cut start)
 G1 X33.17469 Y7.59695
 M5 $0(cut stop)
;end nate oc bracket, cutting #19
;
;begin nate oc bracket #20, cutting, 0.94"
 G0 X33.70469 Y6.65695
 M3 $0 S1 (cut start)
 G1 X33.70469 Y7.59695
 M5 $0(cut stop)
;end nate oc bracket, cutting #20
;
;begin nate oc bracket #21, cutting, 1.60"
 G0 X35.82969 Y7.12695
 M3 $0 S1 (cut start)
 G1 X35.82969 Y7.32695
 G1 X35.82969 Y6.92695
 G1 X35.82969 Y7.12695
 G1 X35.62969 Y7.12695
 G1 X36.02969 Y7.12695
 G1 X35.82969 Y7.12695
 M5 $0(cut stop)
;end nate oc bracket, cutting #21
;
;begin nate oc bracket #22, cutting, 4.44"
 G0 X32.27540 Y4.12589
 M3 $0 S1 (cut start)
 G1 X32.27540 Y8.56589
 M5 $0(cut stop)
;end nate oc bracket, cutting #22
;
;begin nate oc bracket #23, cutting, 2.94"
 G0 X24.99290 Y9.47089
 M3 $0 S1 (cut start)
 G1 X27.93290 Y9.47089
 M5 $0(cut stop)
;end nate oc bracket, cutting #23
;
;begin nate oc bracket #24, cutting, 4.44"
 G0 X22.80540 Y4.12589
 M3 $0 S1 (cut start)
 G1 X22.80540 Y8.56589
 M5 $0(cut stop)
;end nate oc bracket, cutting #24
;
;begin nate oc bracket #25, cutting, 0.94"
 G0 X19.54969 Y8.40995
 M3 $0 S1 (cut start)
 G1 X19.54969 Y7.46995
 M5 $0(cut stop)
;end nate oc bracket, cutting #25
;
;begin nate oc bracket #26, cutting, 0.94"
 G0 X19.01969 Y8.40995
 M3 $0 S1 (cut start)
 G1 X19.01969 Y7.46995
 M5 $0(cut stop)
;end nate oc bracket, cutting #26
;
;begin nate oc bracket #27, cutting, 1.60"
 G0 X17.89469 Y7.93995
 M3 $0 S1 (cut start)
 G1 X18.09469 Y7.93995
 G1 X17.69469 Y7.93995
 G1 X17.89469 Y7.93995
 G1 X17.89469 Y8.13995
 G1 X17.89469 Y7.73995
 G1 X17.89469 Y7.93995
 M5 $0(cut stop)
;end nate oc bracket, cutting #27
;
;begin nate oc bracket #28, cutting, 4.44"
 G0 X20.65040 Y4.12589
 M3 $0 S1 (cut start)
 G1 X20.65040 Y8.56589
 M5 $0(cut stop)
;end nate oc bracket, cutting #28
;
;begin nate oc bracket #29, cutting, 0.94"
 G0 X19.54969 Y2.34795
 M3 $0 S1 (cut start)
 G1 X19.54969 Y1.40795
 M5 $0(cut stop)
;end nate oc bracket, cutting #29
;
;begin nate oc bracket #30, cutting, 0.94"
 G0 X19.01969 Y2.34795
 M3 $0 S1 (cut start)
 G1 X19.01969 Y1.40795
 M5 $0(cut stop)
;end nate oc bracket, cutting #30
;
;begin nate oc bracket #31, cutting, 1.60"
 G0 X17.89469 Y1.87795
 M3 $0 S1 (cut start)
 G1 X17.89469 Y2.07795
 G1 X17.89469 Y1.67795
 G1 X17.89469 Y1.87795
 G1 X18.09469 Y1.87795
 G1 X17.69469 Y1.87795
 G1 X17.89469 Y1.87795
 M5 $0(cut stop)
;end nate oc bracket, cutting #31
;
;begin nate oc bracket #32, cutting, 59.28"
 G0 X17.55630 Y2.34134
 M3 $0 S1 (cut start)
 G3 X17.51969 Y2.25295 I0.08839 J-0.08839
 G1 X17.51969 Y1.50295
 G3 X17.64469 Y1.37795 I0.12500 J0.00000
 G1 X20.52540 Y1.37795
 G3 X20.65040 Y1.50295 I0.00000 J0.12500
 G1 X20.65040 Y2.59589
 G1 X32.77540 Y2.59589
 G3 X32.90040 Y2.72089 I0.00000 J0.12500
 G1 X32.90040 Y6.62695
 G1 X36.07969 Y6.62695
 G3 X36.20469 Y6.75195 I0.00000 J0.12500
 G1 X36.20469 Y7.50195
 G3 X36.07969 Y7.62695 I-0.12500 J-0.00000
 G1 X32.90040 Y7.62695
 G1 X32.90040 Y9.97089
 G3 X32.77540 Y10.09589 I-0.12500 J0.00000
 G1 X20.15040 Y10.09589
 G3 X20.02540 Y9.97089 I0.00000 J-0.12500
 G1 X20.02540 Y8.43995
 G1 X17.64469 Y8.43995
 G3 X17.51969 Y8.31495 I0.00000 J-0.12500
 G1 X17.51969 Y7.56495
 G3 X17.64469 Y7.43995 I0.12500 J0.00000
 G1 X20.02540 Y7.43995
 G1 X20.02540 Y2.37795
 G1 X17.64469 Y2.37795
 G3 X17.55630 Y2.34134 I-0.00000 J-0.12500
 M5 $0(cut stop)
;end nate oc bracket, cutting #32
;
;begin post-amble
 G40 (cutter compensation: off)
 G90 (distance mode: absolute)
 M65 P2 (enable THC)
 M65 P3 (enable torch)
 M68 E3 Q0 (velocity 100%)
 M5 $-1 (backup stop)
;end post-amble
;
;begin statistics
;Pierces = 32
;   Cuts = 32,    Length = 186.72"
;end statistics
;
 M30 (end program)