[Tool0] Type=PlasmaTool Name=A120 Mild Steel 40 amp, 1mm (108V, 5.2 bar) Comment= Tool\ number=1 Kerf\ width=1.4 Plunge\ rate=100 Pierce\ delay=0 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=4.1 Cut\ height=4.1 Pierce\ type=0 Feed\ rate=3266 [Tool0/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool1] Type=PlasmaTool Name=A120 Mild Steel 40 amp, 2mm (108V, 5.2 bar) Comment= Tool\ number=2 Kerf\ width=1.5 Plunge\ rate=100 Pierce\ delay=0 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=4.1 Cut\ height=4.1 Pierce\ type=0 Feed\ rate=2239 [Tool1/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool2] Type=PlasmaTool Name=A120 Mild Steel, 40 amp 3mm (112V, 5.2bar) Comment= Tool\ number=3 Kerf\ width=1.7 Plunge\ rate=100 Pierce\ delay=0.1 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=4.1 Cut\ height=4.1 Pierce\ type=0 Feed\ rate=1794 [Tool2/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool3] Type=PlasmaTool Name=A120 Mild Steel, 40 amp 4mm (114, 5.2bar) Comment= Tool\ number=4 Kerf\ width=1.7 Plunge\ rate=100 Pierce\ delay=0.2 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=4.1 Cut\ height=4.1 Pierce\ type=0 Feed\ rate=1651 [Tool3/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool4] Type=PlasmaTool Name=A120 Mild Steel, 40 amp 5mm (115V, 5.2bar) Comment= Tool\ number=5 Kerf\ width=1.7 Plunge\ rate=100 Pierce\ delay=0.3 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=4.1 Cut\ height=4.1 Pierce\ type=0 Feed\ rate=485 [Tool4/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool5] Type=PlasmaTool Name=A120 Mild Steel, 40 amp 6mm (117V, 5.2bar) Comment= Tool\ number=6 Kerf\ width=1.7 Plunge\ rate=100 Pierce\ delay=0.2 Pause\ at\ end\ of\ cut=0.4 Wiggle\ length=10 Pierce\ height=4 Cut\ height=4.1 Pierce\ type=0 Feed\ rate=1256 [Tool5/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool6] Type=PlasmaTool Name=A120 Mild steel, 40 amp, 8mm (121v, 5.2 Bar) Comment= Tool\ number=7 Kerf\ width=1.7 Plunge\ rate=100 Pierce\ delay=0.5 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=4.1 Cut\ height=4.8 Pierce\ type=0 Feed\ rate=853 [Tool6/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool7] Type=PlasmaTool Name=A120 Mild Steel, 40 amp 10mm (121V, 5.2bar) Comment= Tool\ number=8 Kerf\ width=1.8 Plunge\ rate=100 Pierce\ delay=1.2 Pause\ at\ end\ of\ cut=1.2 Wiggle\ length=10 Pierce\ height=4.1 Cut\ height=4.8 Pierce\ type=0 Feed\ rate=565 [Tool7/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool8] Type=PlasmaTool Name=A120 Mild Steel, 40 amp 12mm (127V, 5.2bar) Comment= Tool\ number=9 Kerf\ width=1.9 Plunge\ rate=100 Pierce\ delay=2 Pause\ at\ end\ of\ cut=1.2 Wiggle\ length=10 Pierce\ height=4.1 Cut\ height=4.1 Pierce\ type=0 Feed\ rate=485 [Tool8/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool9] Type=PlasmaTool Name=A120 Mild Steel 60 amp, 1mm (127V,5.9 bar) Comment= Tool\ number=10 Kerf\ width=2.2 Plunge\ rate=100 Pierce\ delay=0 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=4.1 Cut\ height=4.8 Pierce\ type=0 Feed\ rate=6804 [Tool9/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool10] Type=PlasmaTool Name=A120 Mild Steel 60 amp, 2mm (129V,5.9 bar) Comment= Tool\ number=11 Kerf\ width=2.2 Plunge\ rate=100 Pierce\ delay=0 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=4.8 Cut\ height=4.1 Pierce\ type=0 Feed\ rate=5942 [Tool10/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool11] Type=PlasmaTool Name=A120 Mild Steel 60 amp, 3mm (127V,5.9 bar) Comment= Tool\ number=12 Kerf\ width=2.1 Plunge\ rate=100 Pierce\ delay=0.1 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=4.8 Cut\ height=4.1 Pierce\ type=0 Feed\ rate=5080 [Tool11/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool12] Type=PlasmaTool Name=A120 Mild Steel 60 amp, 4mm (127V,5.9 bar) Comment= Tool\ number=13 Kerf\ width=2.2 Plunge\ rate=100 Pierce\ delay=0 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=4.8 Cut\ height=4.1 Pierce\ type=0 Feed\ rate=3316 [Tool12/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool13] Type=PlasmaTool Name=A120 Mild Steel 60 amp, 5mm (127V,5.9 bar) Comment= Tool\ number=14 Kerf\ width=2.2 Plunge\ rate=100 Pierce\ delay=0.2 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=4.8 Cut\ height=4.1 Pierce\ type=0 Feed\ rate=2794 [Tool13/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool14] Type=PlasmaTool Name=A120 Mild Steel 60 amp, 6mm (134V,5.9 bar) Comment= Tool\ number=15 Kerf\ width=2.1 Plunge\ rate=100 Pierce\ delay=0.3 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=4.8 Cut\ height=4.1 Pierce\ type=0 Feed\ rate=2230 [Tool14/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool15] Type=PlasmaTool Name=A120 Mild Steel, 80 amp, 8mm (131v, 5.9bar) Comment= Tool\ number=16 Kerf\ width=2.5 Plunge\ rate=100 Pierce\ delay=0.5 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=5.1 Cut\ height=4.8 Pierce\ type=0 Feed\ rate=1425 [Tool15/Custom] Preset\ volts=120 DTHC\ delay\ -sec=1.5 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool16] Type=PlasmaTool Name=A120 Mild Steel 60 amp, 10mm (134V,5.9 bar) Comment= Tool\ number=17 Kerf\ width=2.5 Plunge\ rate=100 Pierce\ delay=0.6 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=4.8 Cut\ height=4.1 Pierce\ type=0 Feed\ rate=822 [Tool16/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool17] Type=PlasmaTool Name=A120 Mild Steel 60 amp, 12mm (141V,5.9 bar) Comment= Tool\ number=18 Kerf\ width=2.5 Plunge\ rate=100 Pierce\ delay=0.6 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=4.8 Cut\ height=4.1 Pierce\ type=0 Feed\ rate=646 [Tool17/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool18] Type=PlasmaTool Name=A120 Mild Steel 80 amp, 1mm (116V,5.9 bar) Comment= Tool\ number=19 Kerf\ width=1.6 Plunge\ rate=100 Pierce\ delay=0 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=5.1 Cut\ height=3.3 Pierce\ type=0 Feed\ rate=7895 [Tool18/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool19] Type=PlasmaTool Name=A120 Mild Steel 80 amp, 2mm (114V,5.9 bar) Comment= Tool\ number=20 Kerf\ width=1.6 Plunge\ rate=100 Pierce\ delay=0.1 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=5.1 Cut\ height=3.3 Pierce\ type=0 Feed\ rate=6395 [Tool19/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool20] Type=PlasmaTool Name=A120 Mild Steel 80 amp, 3mm (112V,5.9 bar) Comment= Tool\ number=21 Kerf\ width=1.5 Plunge\ rate=100 Pierce\ delay=0.1 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=5.1 Cut\ height=3.3 Pierce\ type=0 Feed\ rate=4895 [Tool20/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool21] Type=PlasmaTool Name=A120 Mild Steel 80 amp, 4mm (115V,5.9 bar) Comment= Tool\ number=22 Kerf\ width=1.7 Plunge\ rate=100 Pierce\ delay=0.3 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=5.1 Cut\ height=4.8 Pierce\ type=0 Feed\ rate=4025 [Tool21/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool22] Type=PlasmaTool Name=A120 Mild Steel 80 amp, 5mm (123V,5.9 bar) Comment= Tool\ number=23 Kerf\ width=2 Plunge\ rate=100 Pierce\ delay=0.3 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=5.1 Cut\ height=4.8 Pierce\ type=0 Feed\ rate=3300 [Tool22/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool23] Type=PlasmaTool Name=A120 Mild Steel 80 amp, 6mm (126V,5.9 bar) Comment= Tool\ number=24 Kerf\ width=2.2 Plunge\ rate=100 Pierce\ delay=0.4 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=5.1 Cut\ height=4.8 Pierce\ type=0 Feed\ rate=2735 [Tool23/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool24] Type=PlasmaTool Name=A120 Mild Steel 80 amp, 8mm (131V,5.9 bar) Comment= Tool\ number=25 Kerf\ width=2.5 Plunge\ rate=100 Pierce\ delay=0.5 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=5.1 Cut\ height=4.8 Pierce\ type=0 Feed\ rate=1745 [Tool24/Custom] Preset\ volts=120 DTHC\ delay\ -sec=1.5 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool25] Type=PlasmaTool Name=A120 Mild Steel 80 amp, 10mm (134V,5.9 bar) Comment= Tool\ number=26 Kerf\ width=2.6 Plunge\ rate=100 Pierce\ delay=0.5 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=5.1 Cut\ height=4.8 Pierce\ type=0 Feed\ rate=1000 [Tool25/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool26] Type=PlasmaTool Name=A120 Mild Steel 80 amp, 12mm (136V,5.9 bar) Comment= Tool\ number=27 Kerf\ width=2.6 Plunge\ rate=100 Pierce\ delay=0.5 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=5.1 Cut\ height=4.8 Pierce\ type=0 Feed\ rate=935 [Tool26/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool27] Type=PlasmaTool Name=A120 Mild Steel 80 amp, 15mm (143V,5.9 bar) Comment= Tool\ number=28 Kerf\ width=2.6 Plunge\ rate=100 Pierce\ delay=0.5 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=5.1 Cut\ height=4.8 Pierce\ type=0 Feed\ rate=580 [Tool27/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool28] Type=PlasmaTool Name=A120 Mild Steel 100 amp, 6mm (114V,5.2 bar) Comment= Tool\ number=29 Kerf\ width=2 Plunge\ rate=100 Pierce\ delay=0 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=4.6 Cut\ height=4.1 Pierce\ type=0 Feed\ rate=2210 [Tool28/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool29] Type=PlasmaTool Name=A120 Mild Steel 100 amp, 8mm (113V,5.2 bar) Comment= Tool\ number=30 Kerf\ width=2.2 Plunge\ rate=100 Pierce\ delay=0.1 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=4.6 Cut\ height=4.1 Pierce\ type=0 Feed\ rate=1960 [Tool29/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool30] Type=PlasmaTool Name=A120 Mild Steel 100 amp, 10mm (112V,5.2 bar) Comment= Tool\ number=31 Kerf\ width=2.3 Plunge\ rate=100 Pierce\ delay=0.2 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=4.6 Cut\ height=4.1 Pierce\ type=0 Feed\ rate=1665 [Tool30/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool31] Type=PlasmaTool Name=A120 Mild Steel 100 amp, 12mm (114V,5.2 bar) Comment= Tool\ number=32 Kerf\ width=2.4 Plunge\ rate=100 Pierce\ delay=0.3 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=4.6 Cut\ height=4.1 Pierce\ type=0 Feed\ rate=1185 [Tool31/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool32] Type=PlasmaTool Name=A120 Mild Steel 100 amp, 15mm (121V,5.2 bar) Comment= Tool\ number=33 Kerf\ width=2.5 Plunge\ rate=100 Pierce\ delay=0.4 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=4.6 Cut\ height=4.1 Pierce\ type=0 Feed\ rate=1185 [Tool32/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool33] Type=PlasmaTool Name=A120 Mild Steel 100 amp, 20mm (128V, 5.2 bar) Comment= Tool\ number=34 Kerf\ width=2.8 Plunge\ rate=100 Pierce\ delay=0.8 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=5 Cut\ height=4.1 Pierce\ type=0 Feed\ rate=1185 [Tool33/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool34] Type=PlasmaTool Name=A120 Mild Steel 120 amp, 6mm (139V,5.5 bar) Comment= Tool\ number=35 Kerf\ width=2.8 Plunge\ rate=100 Pierce\ delay=0.2 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=5.1 Cut\ height=3.2 Pierce\ type=0 Feed\ rate=2210 [Tool34/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool35] Type=PlasmaTool Name=A120 Mild Steel 120 amp, 8mm (140V,5.5 bar) Comment= Tool\ number=36 Kerf\ width=2.8 Plunge\ rate=100 Pierce\ delay=0.2 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=5.1 Cut\ height=3.2 Pierce\ type=0 Feed\ rate=3070 [Tool35/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool36] Type=PlasmaTool Name=A120 Mild Steel 120 amp, 10mm (142V,5.5 bar) Comment= Tool\ number=37 Kerf\ width=2.8 Plunge\ rate=100 Pierce\ delay=0.3 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=5.1 Cut\ height=3.2 Pierce\ type=0 Feed\ rate=2120 [Tool36/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool37] Type=PlasmaTool Name=A120 Mild Steel 120 amp, 12mm (142V,5.5 bar) Comment= Tool\ number=38 Kerf\ width=2.8 Plunge\ rate=100 Pierce\ delay=0.5 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=5.1 Cut\ height=3.2 Pierce\ type=0 Feed\ rate=2210 [Tool37/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool38] Type=PlasmaTool Name=A120 Mild Steel 120 amp, 15mm (143V,5.5 bar) Comment= Tool\ number=39 Kerf\ width=2.8 Plunge\ rate=100 Pierce\ delay=0.7 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=4.8 Cut\ height=3.2 Pierce\ type=0 Feed\ rate=1355 [Tool38/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool39] Type=PlasmaTool Name=A120 Mild Steel 120 amp, 20mm (152V,5.5 bar) Comment= Tool\ number=40 Kerf\ width=2.8 Plunge\ rate=100 Pierce\ delay=1.6 Pause\ at\ end\ of\ cut=0.5 Wiggle\ length=10 Pierce\ height=6.4 Cut\ height=4.4 Pierce\ type=0 Feed\ rate=725 [Tool39/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [Tool40] Type=PlasmaTool Name=CenterPunch Comment= Tool\ number=50 Kerf\ width=1.2 Plunge\ rate=100 Pierce\ delay=0 Pause\ at\ end\ of\ cut=0 Wiggle\ length=10 Pierce\ height=5.1 Cut\ height=4.8 Pierce\ type=0 Feed\ rate=1910 [Tool40/Custom] Preset\ volts=49 DTHC\ delay\ -sec=0 Tip\ Size\ -Amps=40 NO\ DTHC\ -\ 0=1 [pathRules] GlobalRule=-1