Plasma THC Corner Lock

#net thc-volts-tol pyvcp.volts-tolerance

<spinbox> <width>"5"</width> <halpin>"vel-tol"</halpin> <min_>.01</min_> <max_>1</max_> <resolution>0.01</resolution> <initval>0.2</initval> <format>"1.2f"</format> <font>("Arial",10)</font>

component thc "Torch Height Control"; description """ Torch Height Control Mesa THC > Encoder > LinuxCNC THC component The Mesa THC sends a frequency based on the voltage detected to the encoder. The velocity from the encoder is converted to volts with the velocity scale parameter inside the THC component. The THCAD card sends a frequency at 0 volts so the scale offset parameter is used to zero the calculated voltage. Component Functions If enabled and torch is on and X + Y velocity is within tolerance of set speed allow the THC to offset the Z axis as needed to maintain voltage. If enabled and torch is off and the Z axis is moving up remove any correction at a rate not to exceed the rate of movement of the Z axis. If enabled and torch is off and there is no correction pass the Z position and feed back untouched. If not enabled pass the Z position and feed back untouched. Physical Connections .br Plasma Torch Arc Voltage Signal => 6 x 487k 1% resistors => THC Arc Voltage In .br THC Frequency Signal => Encoder #0, pin A (Input) .br Plasma Torch Arc OK Signal => input pin .br output pin => Plasma Torch Start Arc Contacts HAL Plasma Connections .br encoder.nn.velocity => thc.encoder-vel (tip voltage) .br motion.spindle-on => output pin (start the arc) .br thc.arc-ok <= motion.digital-in-00 <= input pin (arc ok signal) HAL Motion Connections .br thc.requested-vel <= motion.requested-vel .br thc.current-vel <= motion.current-vel """; author "John Thornton"; license "GPLv2 or greater"; option singleton yes; // Input Pins pin in float encoder_vel "Connect to hm2_5i20.0.encoder.00.velocity"; pin in float current_vel "Connect to motion.current-vel"; pin in float requested_vel "Connect to motion.requested-vel"; pin in float volts_requested "Tip Volts current_vel >= min_velocity requested"; pin in float vel_tol "Velocity Tolerance (Corner Lock)"; pin in bit torch_on "Connect to motion.spindle-on"; pin in bit arc_ok "Arc OK from Plasma Torch"; pin in bit enable "Enable the THC, if not enabled Z position is passed through"; pin in float z_pos_in "Z Motor Position Command in from axis.n.motor-pos-cmd"; // Output Pins pin out float z_pos_out "Z Motor Position Command Out"; pin out float z_fb_out "Z Position Feedback to Axis"; pin out float volts "The Calculated Volts"; pin out bit vel_status "When the THC thinks we are at requested speed"; pin out float offset_value "The Current Offset"; // Parameters param rw float vel_scale "The scale to convert the Velocity signal to Volts"; param rw float scale_offset "The offset of the velocity input at 0 volts"; param rw float velocity_tol "The deviation percent from planned velocity"; param rw float voltage_tol "The deviation of Tip Voltage before correction takes place"; param rw float correction_vel "The amount of change in user units per period to move Z to correct"; // Global Variables variable float offset; variable float last_z_in; function _; ;; #include "rtapi_math.h" FUNCTION(_) { // convert encoder velocity to volts volts = (encoder_vel - scale_offset) * vel_scale; if(volts < 0){volts = 0;} // make sure volts is not negative offset_value = offset; if(enable){ float min_velocity = requested_vel -(requested_vel*(velocity_tol*0.01)); if(current_vel > 0 && current_vel >= min_velocity){vel_status = 1;} else {vel_status =0;} if(torch_on && arc_ok && vel_status){ // allow correction if((volts + voltage_tol) > volts_requested){ offset -= correction_vel; } if((volts - voltage_tol) < volts_requested){ offset += correction_vel; } last_z_in = 0; } if(!torch_on){ // remove any offset float z_diff; z_diff = z_pos_in - last_z_in; if(z_diff > 0 && offset != 0){ // torch is moving up if(offset > 0){ // positive offset if(offset > z_diff){ // remove some offset -= z_diff; } else {offset = 0;} } if(offset < 0){ // negative offset if(offset < z_diff){ // remove some offset += z_diff; } else {offset = 0;} } } last_z_in = z_pos_in; } z_pos_out = z_pos_in + offset; z_fb_out = z_pos_in; // keep axis motor position fb from being confused } if(!enable){ z_pos_out = z_pos_in; z_fb_out = z_pos_in; // keep axis motor position fb from being confused } }