component compile problem

More
8 years 5 months ago #110950 by Skidloaders1
Replied by Skidloaders1 on topic component compile problem
Good day Andy

Thanks for the reply, what i meant was are some off the other files available like .hal and .ini?

rgds Wilfried

Please Log in to join the conversation.

More
8 years 5 months ago #110952 by andypugh
Replied by andypugh on topic component compile problem

Skidloaders1 wrote: Thanks for the reply, what i meant was are some off the other files available like .hal and .ini?


I was asking a new question, not answering your previous one.

I will see if I can track down the Weiler config.

Please Log in to join the conversation.

More
8 years 5 months ago #110963 by Skidloaders1
Replied by Skidloaders1 on topic component compile problem
Good day Andy

1)The carousel.0.sense pins do change according to the rotation
2) the carousel.0.active pin is not connected to anything
3) the iocontrol.0.tool-change pin never goes active ( T2 + M6 command )
rgds Wilfried

Please Log in to join the conversation.

More
8 years 5 months ago #110965 by andypugh
Replied by andypugh on topic component compile problem
That sounds like the tool-prepared pin isn't being set after tool-prepare goes high?

Please Log in to join the conversation.

More
8 years 5 months ago #110999 by rene-dev
Replied by rene-dev on topic component compile problem
This is the relevant bit from the weiler lathe andy mentioned.
I hope its the latest version, let me know if it doesnt work.
the encoder inputs are connected according to the original schematic, which also matches the documentation for the encoder.
the reverse and forward you have to try.
Code:
loadrt carousel pockets=8 encoding="binary" pty=0 addf carousel.0 servo-thread net tool-num iocontrol.0.tool-prep-pocket => carousel.0.pocket-number net tool-change iocontrol.0.tool-change => carousel.0.enable net tool-changed carousel.0.ready => iocontrol.0.tool-changed net rev1 carousel.0.motor-fwd => hm2_7i92.0.7i77.0.0.output-04#reverse net rev2 carousel.0.motor-rev => hm2_7i92.0.7i77.0.0.output-05#fwd net reva carousel.0.sense-0 net revb carousel.0.sense-1 net revc carousel.0.sense-2 net revd carousel.0.sense-3 net revs carousel.0.strobe net revp carousel.0.parity

Please Log in to join the conversation.

More
8 years 5 months ago #111012 by Skidloaders1
Replied by Skidloaders1 on topic component compile problem
Thanks Andy
Does tool-prepared not mean that the carousel/turret is now in its commanded position?

rgds W

Please Log in to join the conversation.

More
8 years 5 months ago #111013 by Skidloaders1
Replied by Skidloaders1 on topic component compile problem
Thank rene-dev

My carousel(turret) has 4 positions with sense pins at every position.
Turns only in one direction ( hydraulic push - pull ratchet system) see video above somewhere
encoding = single ( I believe)
regards W

Please Log in to join the conversation.

More
8 years 5 months ago #111014 by Skidloaders1
Replied by Skidloaders1 on topic component compile problem
Good day Rene-dev

My Weiler lathe must be a older unit i guess
anno early 1980's ( still a solid and accurate unit - super over designed )

Please Log in to join the conversation.

More
8 years 5 months ago #111015 by rene-dev
Replied by rene-dev on topic component compile problem
ah, that looks completely different from mine, didnt see the video before my first post...
this type of toolchanger cannot preselect, so the prepare pins need to be loopbacked.



Rene

Please Log in to join the conversation.

More
8 years 5 months ago #111017 by rene-dev
Replied by rene-dev on topic component compile problem

Skidloaders1 wrote: Does tool-prepared not mean that the carousel/turret is now in its commanded position?

no, prepare means preselect the next tool.
some toolchangers can get the next tool before you need it, so the actual change is quicker.
yours cannot do that.
preselecting is explained in this video:

Please Log in to join the conversation.

Time to create page: 0.072 seconds
Powered by Kunena Forum