M52 M53 possible activate in jog mode too?

not try jet ... but ask if possible use motion.feed-hold and motion.adaptive-speed in manual mode too ... so need activate M52 and M53 outside gcode too I think ....there are a way? 

Where find M52 and M53 routine codes?

regards

 

'motion.feed-hold' has no effect when jogging so maybe try 'motion.jog-inhibit' or 'motion.jog-stop' instead.
M52 also has no effect on jogging. Workarounds for this will depend somewhat on the gui you are using. Gmoccapy offers convenient hal pins to handle jog speed while in 'Axis Gui' you might have to use 'halui.axis.jog-speed' to set the speed and 'halui.axis.L.minus' and 'halui.axis.L.plus' to do the jogging. 'halui.axis.L.analog' might also be of interest as that will allow to scale the jog speed between -1..1.

Note that in some guis (like 'Axis') these halpins will be overridden by the jog buttons in the gui.

linuxcnc.org/docs/html/man/man1/halui.1.html

bkt wrote:

not try jet ... but ask if possible use motion.feed-hold and motion.adaptive-speed in manual mode too ... so need activate M52 and M53 outside gcode too I think ....there are a way? 
 

I don't think that there is a way, as jogging / manual uses a different motion planner than coordinated mode. 

motion.feed-hold .... just try work perfect in joint jog mode, and world jog mode .... work perfect ... think no problem to work in gcode too.

motion.adaptive-feed .... not work .... but maybe can work .... not find M52 and M53 code so not understand what they do and how they do it ....
 

motion.feed-hold .... just try work perfect in joint jog mode, and world jog mode .... work perfect ... think no problem to work in gcode too.

Hm, not sure what you are doing but I tried it also and for me it sure does not work on Version 2.9. Neither joint or axis jog is affected by motion.feed-hold and since jogging uses a different planner I'm not sure how it could.

maybe because you use some standard linuxcnc gui .... not sure about version data but I've a 2.9 linuxcnc, and use a c++ gui .... exchange signal and value is trought nml, and pin value on shemem ... for these reason think I have these effect that you not have .... and for that reason think can try to have some result on M52 code when discover where is placed on (folder and name file) .... maybe not but if not see it is impossible to discover ...

Any how I try to limit velocity near singularity issue zone .... for now I drive the change using a pin from my kinematics that check when i reach singularity zone and halui.axis.jog-speed pin .... in these way everytime "enter" in "danger" zone can set a lower velocity .... but logic of mechanism is not clean so try to do somethings more clear and clean only for that pourpose ....

regards

regards

@andyPugh  ..... mmmm ... you think switchkins in joint mode not use same motion planner than coordinate mode? curious ....

What he meant is that _jogging_ does not use the same planner.
Switchkins does not change the planner.

Ok understand ... obviusly switchkins not change plan .... but drive joint and axis too ... because for drive (or regulate velocity) of joint need to use joint .... I think can work in jogging mode too .... HOW??? I think if can study M52 script (that not find probabily because name in different way) can understand if my ideas was wrong or not ....I know my English is pitiful, be patient... I'm also old

regards

Any how I discove today MDI command (trough shell) develop from andyPugh? real thanks for that ... very fine and helpful (in general for uses Lcnc ... not for these thread).

regards