Need Help in Kinamatics of Small DIY 6dof robotic arm.

More
1 year 3 days ago #337277 by amanker
Need Help in Kinamatics of Small DIY 6dof robotic arm. was created by amanker
I have configured and installed LinuxCNC on RPI5 and I can control individual joint of robotic arm using trivkins. Using PCA9685 as PWM servo controller. Its work good. But I am strugling to get its kinamatic working. Here is photo of my arm with measurements. 
Here is photo of My robotic arm
 

Attachment not found



Here are the pin values I used in genserkins
Code:
setp genserkins.A-0 0  setp genserkins.ALPHA-0 0  setp genserkins.D-0 83.5  setp genserkins.A-1 45  setp genserkins.ALPHA-1 -1.570796327  setp genserkins.D-1 0  setp genserkins.A-2 100.4  setp genserkins.ALPHA-2 0  setp genserkins.D-2 0  setp genserkins.A-3 12  setp genserkins.ALPHA-3 -1.570796327  setp genserkins.D-3 195  setp genserkins.A-4 0  setp genserkins.ALPHA-4 1.570796327  setp genserkins.D-4 0  setp genserkins.A-5 0  setp genserkins.ALPHA-5 -1.570796327  setp genserkins.D-5 58

Please Log in to join the conversation.

More
1 year 3 days ago #337287 by Aciera
Replied by Aciera on topic Need Help in Kinamatics of Small DIY 6dof robotic arm.
There is documentation on how to set up genserkins:
www.linuxcnc.org/docs/stable/html/motion/dh-parameters.html

I can't quite tell from the picture how many joints your arm has but genserkins will only work for manipulators with 6 joints.

Please Log in to join the conversation.

More
1 year 3 days ago #337295 by amanker
Replied by amanker on topic Need Help in Kinamatics of Small DIY 6dof robotic arm.
I have read all documents and tried to understand DH parameters and how kinamatics works. And read the documents many times to have good grap of the subject. I tried my best to explain geometry of my DIY arm.
I am attaching photo explaining more about geometry of arm.
 

Attachment not found



I hope this might better explain geometry of robotic arm.

Please Log in to join the conversation.

More
1 year 3 days ago #337298 by Aciera
Replied by Aciera on topic Need Help in Kinamatics of Small DIY 6dof robotic arm.
With all joints in the zero position does the arm point down towards the floor as shown in the documentation?
Maybe you could elaborate a bit on what isn't working.

Please Log in to join the conversation.

More
1 year 3 days ago #337300 by amanker
Replied by amanker on topic Need Help in Kinamatics of Small DIY 6dof robotic arm.
It's giving kinamaticsInverse failed error. As per documents joints can't have offset values. So to align J1 and J2 these must be in line, arm j1-j2 should be horizontal to give offset values zero. But practically I can't make arm in this position.

Please Log in to join the conversation.

More
1 year 3 days ago #337320 by heaven
Replied by heaven on topic Need Help in Kinamatics of Small DIY 6dof robotic arm.
Maybe you are in singularities, try another homing position

Please Log in to join the conversation.

More
1 year 3 days ago #337323 by amanker
Replied by amanker on topic Need Help in Kinamatics of Small DIY 6dof robotic arm.
I want to know did I used correct values for genserkins pins according to my geometry

Please Log in to join the conversation.

More
1 year 3 days ago #337328 by Aciera
Replied by Aciera on topic Need Help in Kinamatics of Small DIY 6dof robotic arm.
1. I don't see anything obviously wrong with your DH parameters
2. I would agree with @heaven that you are in a singular position. Which will lead to the inverse kinematics failing. In your pictures j5 is collinear with j3. Trying a different start position for j4 should help.

Please Log in to join the conversation.

More
1 year 3 days ago #337332 by amanker
Replied by amanker on topic Need Help in Kinamatics of Small DIY 6dof robotic arm.
Thanks @Aciera
Finally got it working. Added Home Offset and Home Values to Joint_1 since it was not aligned as in documents and I cant give my arm that postion due to its hardware limits. So Accordingly defined Home and HomeOffset. and Small offset to J2 so that I remain horizontal. And minor offsets to J4. and Assiged Home location of J4 so that it remains vertical.
Thanks a lot.
Yes as @Aciera mentioned DH parameters are good.

Please Log in to join the conversation.

Time to create page: 0.093 seconds
Powered by Kunena Forum