Remora - ethernet NVEM / EC300 / EC500 cnc board

cakeslob wrote:

Warning: Spoiler!

that is because this is wrongMAX_ACCELERATION = 2000000
and this does nothing no matter what valueDIR_HOLD = 50000

did your setup work before with mach3?

if it is stepper timing related you need to load the DMA stepgen config and adjust your step timing accordingly

 

Of course, I also put the photo of the parameters on mach3, but on mach3 I have another control board and it has 4 wires with ENABLE, I wrote it in the first post. Here Enable is disconnected but I also tried to connect it to +5V (+com)

sorry i dont understand, maybe i missed some step,
here you say everything is ok.
what is not working? Have you tried on other axes?

jjdege wrote:

sorry i dont understand, maybe i missed some step,
here you say everything is ok.
what is not working? Have you tried on other axes?

yes the direction of rotation and all the axes respond, you have some axes that don't work at all! Mine work but not smoothly!

unfortunately with NVEM I had a bad experience, even with drivers other than TB6560, it could be my fault.
With EC500 after a moment of panic for the time out,
it was possible to recover and it worked on the first try

it is not necessarily the same for you

My project is slowly progressing. I've put together a few things using examples and AI. The interface starts, but I'm stuck in the ESTOP. The statuses in HALSHOW aren't changing either. So there seems to be no connection to the board, even though pinging 10.10.10.10 is successful. Is there a way I can test the communication?         

sorry
in custom file 2025-05-05.hal
try with

aDm1N wrote:

My project is slowly progressing. I've put together a few things using examples and AI.

Warning: Spoiler!

The interface starts, but I'm stuck in the ESTOP. The statuses in HALSHOW aren't changing either. So there seems to be no connection to the board, even though pinging 10.10.10.10 is successful. Is there a way I can test the communication? 

Attachment not found

 

Attachment not found

 

Attachment not found

 

Attachment not found

 

Attachment not found

AI does not exist, it is just a big script with access to a huge database of data. Most of the time it responds randomly. It only helps you if you know, for example, C++ very well and then you have to correct all the errors it makes ... basically you have to re-do everything yourself.

I advise you to never use it again, it is a scam!

I have recreated the problem with the function generator. Now I am sure the problem lies in the configuration, or so I believe. For now, I would like to know which parameters I need to set to have the same parameters for frequency and pulse times in the hal and ini files (like pulse 1,000,000ns frequency 988Hz). Thank you again for your patience!

 

Been spending the last day or so in an attempt to configure the external E-stop. I found this - www.forum.linuxcnc.org/18-computer/44828...rd?start=2080#324903 - and tried to place that into my .hal file (the basic stock one that is in the repo - github.com/scottalford75/Remora-RT1052-c...sic/remora-ec500.hal ) like I was able to do for the limit switches and got several already active errors. Commenting those offending lines out allowed the gui to run but no working E-stop. I looked here -  remora-docs.readthedocs.io/en/latest/software/hal-examples.html - and there is no mention of E-stop.

I am thinking that the E-stop needs to be set up in some manner similar to the limit switches like this - [/code]

This is my E-stop in my .hal file.

net nvem-estop <= estop-latch.0.fault-in <= remora.input.14

It's just a switch. Once the input is triggered it should work.