Remora - ethernet NVEM / EC300 / EC500 cnc board

Got my second ST-Link programmed. I get a error file in the directory after reboot when I try and flash remora-rt1052.bin. The ST-Link Looks the DAP-Link is working correctly. I'm going to try and flash from MCUexpresso. What SDK's do I need to install? Never used MCUexpresso but I've I've used visual studio code and arduino IDE allot. 

I'm getting a network error when compiling. Did know if I was missing a SDK or there is a syntax error. All the errors I'm getting are ethernet related. 

../source/ethernet.c:30:73: error: 'phy_handle_t' {aka 'struct _phy_handle'} has no member named 'mdioHandle'

phy_handle_t' {aka 'struct _phy_handle'} has no member named 'mdioHandle'



 

Hi, you could try to install the SDK_2.x_MIMXRT1052xxxxB SDK to see if that helps.

I don't think it will be a source code issue as others are compiling ok.

Did you clone or copy the repo?

Downloaded the ZIP, I have that processor SDK installed. The issue seems ethernet related. I'm trying a few ways to get the firmware on the MCU. I'm trying The daplink process get The RT1052 Drive in windows. When I copy the remora firmware I get a text  file called FAIL.TXT  after its reboots

error: Failed to initialize the target MCU
type: target

hey fintech 

replied on your yt video already. 
here is a dll file that works with mach3 and the original firmwared ec500 V5
 
i got this from the manufacturer found on alibaba.
still has some issues but things are moving
so moving to remora and linuxcnc is not an option, it's a must! 
but for so long you can try to make your motors move

Holy Shit!!! I got it flashed.

• Flash second ST-Link with CMSIS-DAP-STLINK21.hex
• Install Python
• Open Command prompt with admin access
• Make sure you change directories where the files are located
• Run The Following commands

python -m pip install -U pyocd

• Install Remora Firmware

pyocd flash .\remora-rt1052.bin --target mimxrt1050_quadspi

• Flash Back to mach3

 pyocd flash .\ec500.bin --target mimxrt1050_quadspi

             





 

Thanks, I'm probably will have to convert to LinuxCNC. I have an NVEM setup with LinuxCNC I'm playing with.. I just hope the issues I'm having with stepper control and outputs is a firmware issue and not hardware problem

fintech wrote:

Holy Shit!!! I got it flashed.

• Flash second ST-Link with CMSIS-DAP-STLINK21.hex
  • Install Python
    • Open Command prompt with admin access
      • Make sure you change directories where the files are located
        • Run The Following commands
          
          python -m pip install -U pyocd
          • Install Remora Firmware
            
            pyocd flash .\remora-rt1052.bin --target mimxrt1050_quadspi
            • Flash Back to mach3
              
               pyocd flash .\ec500.bin --target mimxrt1050_quadspi
              
                           
              
              
              
              
              
               

Great to hear. I think I will remove the DAPLink stuff from the repo as to many people are having issues with it. pyOCD with CMSIS-DAP probe seems more reliable.

I'm not sure what was up with my mach3 firmware. I got stepper control to work with LinuxCNC and remora firmware. I'm warming up to linuxCNC after that mach3 debacle. Anybody get this to work with Probe_basic? Any configs would be great. I'm still getting familiar with the Hal and config files.

Now I see what you mean about the IO pinout headache for these BGA processors. At least with the STM32 you can put your leads on the pin. Do you think this new NXP processors is an upgrade or downgrade?