Machine Coordinates from G-Code, #<_hal[]> support

More
7 years 7 months ago #129944 by tommylight
Replied by tommylight on topic Machine Coordinates from G-Code, #<_hal[]> support
Is this probing for plasma ?

Please Log in to join the conversation.

More
7 years 7 months ago #129948 by spicer
Replied by spicer on topic Machine Coordinates from G-Code, #<_hal[]> support
Yes.
Test video you see here:
www.xup.in/dl,15200380/plasma_kopf.MOV/
The hole on top is for the 12mm capacitive (or inductive) sensor.

I work with 2 dimensions ^^
Code:
measuretool.ngc o<measuretool> sub ; setup G49 (cancel tool lengths) G91 (incremental mode) G28.1 (copy absolute coordinates into #5161-#5169) #1002=[-#5163] (probe depth) ; measure G38.2 Z#1002 F20 (Z probe) G92 Z-2.05 (distance switch_on to Workpiece surface) G90 G0 Z1 (after probing move to 1mm up from workpiece) o<measuretool> endsub M2

This is very easy for the user.
It have 2 buttons. One for XY zeroing,
other for probing.
The solution of the problem "MDI mode" is here
forum.linuxcnc.org/24-hal-components/363...i-mdi-command#129952

Please Log in to join the conversation.

More
7 years 7 months ago #129957 by pl7i92
Replied by pl7i92 on topic Machine Coordinates from G-Code, #<_hal[]> support
why at all does your plasma use XY Zeroing
i got on all 4 Plasmas we use a Fix XY zero wher the sheet is fixed to and all programms use this zero

ok i only got 1x1meter sheets no inlays

but the Homing refers to this point and then Z touchoff as you do it
i

the Fix Zero makes life very easy
one button press and then run

Please Log in to join the conversation.

More
7 years 7 months ago #129966 by tommylight
Replied by tommylight on topic Machine Coordinates from G-Code, #<_hal[]> support
Why are you not using one of the configs that have automated probe in hal ?
forum.linuxcnc.org/plasma-laser/34978-th...-with-how-to?start=0
Choose one depending on your hardware.

Please Log in to join the conversation.

More
7 years 7 months ago #129970 by spicer
Replied by spicer on topic Machine Coordinates from G-Code, #<_hal[]> support

pl7i92 wrote: why at all does your plasma use XY Zeroing
i got on all 4 Plasmas we use a Fix XY zero wher the sheet is fixed to and all programms use this zero

ok i only got 1x1meter sheets no inlays

but the Homing refers to this point and then Z touchoff as you do it
i

the Fix Zero makes life very easy
one button press and then run


Mostly we will not use XY-zeroing.
This is just so that you have the possibility, if perhaps even a workpiece is not in the corner.

@tommylight
That would have been a possibility, of course.
I have not seen the thread before.

Please Log in to join the conversation.

More
7 years 7 months ago #129976 by pl7i92
Replied by pl7i92 on topic Machine Coordinates from G-Code, #<_hal[]> support
if you are on THC
toms config changes on every M3 is a waist of time
with 100 M3 in files it is a nightmare on theroing up

Personal expirience

Please Log in to join the conversation.

More
7 years 7 months ago #129999 by tommylight
Replied by tommylight on topic Machine Coordinates from G-Code, #<_hal[]> support

spicer wrote: I have not seen the thread before.

:ohmy:

pl7i92 wrote: toms config changes on every M3 is a waist of time
with 100 M3 in files it is a nightmare on theroing up


It does not "changes on every M3", it does probe for material on every M3.
Here that is a must as the material used here is the bottom quality, so it warps a lot. Also i have some very fast Z axis that can do 6000mm per minute and have 28 cm travel ! :) Probe time = 1 second

Please Log in to join the conversation.

More
7 years 6 months ago #130077 by pl7i92
Replied by pl7i92 on topic Machine Coordinates from G-Code, #<_hal[]> support
I have seen people with 5mm bent table not doing probing at all as the thc jumps in and goes to the given Voltige down
within a mm of travel at 6m/min
even on Torch fire-ring startup at 5mm from material

Please Log in to join the conversation.

Time to create page: 0.324 seconds
Powered by Kunena Forum