How can I make the axis movement immediate in the remapping code?

chen1234
Topic Author
Offline
Senior Member

4 years 9 months ago #233144 by chen1234

How can I make the axis movement immediate in the remapping code? was created by chen1234

I did an io signal detection in the remapping code, it can control the Z axis movement after reading a high level signal, I use the (self.execute("G0 Z %d"%b)) function to Control the Z axis, b is my parameter, but I found in the test that self.execute will not be executed in the loop, but will be executed after the loop ends, which cannot achieve my needs. I would like to know how to control the axis to make it execute immediately? Please give me some advice.
Thanks, here is my code:

Code:

def m203(self,**words):
    #yield INTERP_EXECUTE_FINISH
    if self.task:
        a = (words['s'])
        b = a
        c = 0
        while 1：
            x = hal.get_value('lcec.0.5.RXPDO-4')  
            if x == 1:
                y = hal.get_value('lcec.0.5.RXPDO-5')  
                if y == 1:
                    while 1:
                        y = hal.get_value('lcec.0.5.RXPDO-5') 
                        if y == 0:
                            c += 1
                            print("c = ", c)
                            if b < 44 and b >-44:
                                self.execute("G0 Z %d"%b)
                                b += a
                                break 
                elif y == 0:
                    time.sleep(0)
            elif x == 0 or hal.get_value('lcec.0.5.TXPDO-2') == 1:
                break 

Please Log in to join the conversation.

cmorley
Offline
Platinum Member

4 years 9 months ago #233151 by cmorley

Replied by cmorley on topic How can I make the axis movement immediate in the remapping code?

try:
yield INTERP_EXECUTE_FINISH

after execute statement

Please Log in to join the conversation.

chen1234
Topic Author
Offline
Senior Member

4 years 9 months ago #233249 by chen1234

Replied by chen1234 on topic How can I make the axis movement immediate in the remapping code?

Thanks for your answer,
I solved the problem, I found that (self.execute("G0 Z %d"%b)) can't go to execute the Z axis movement immediately.
I solved the Z axis control delay using ( External Axis Offsets ) and it got my Z axis feeds working. I thought I should share the solution, below is my code and configuration.
remap.py:

Code:

def m203(self,**words):
    yield INTERP_EXECUTE_FINISH
    if self.task:
        a = (words['s'])
        b = a
        while 1 :
            y = hal.get_value('lcec.0.5.RXPDO-4')  
            if y == 1:            
                x = hal.get_value('lcec.0.5.RXPDO-5')  
                if x == True:
                    while 1:
                        x = hal.get_value('lcec.0.5.RXPDO-5')
                        if x == False:
                            hal.set_p("axis.z.eoffset-counts","%d"%b)
                            print("b=",b)
                            b += a
                            break  
                elif x == False:
                    time.sleep(0)   
            elif y == 0 or shal.get_value('lcec.0.5.TXPDO-2') == 1:
                time.sleep(0)
                break 
        hal.set_p("axis.z.eoffset-counts","0")
       

myaxis.ini:

Code:

[AXIS_Z]
OFFSET_AV_RATIO  =   0.2

myaxis.hal:

Code:

setp axis.z.eoffset-enable 1
setp axis.z.eoffset-scale 1

Please Log in to join the conversation.

Time to create page: 0.446 seconds