Assigning 2 funcitons to one button

More
9 years 2 months ago #96974 by czerech
Assigning 2 funcitons to one button was created by czerech
Hello all!

I have a problem, and maybe you will be able to help me.

I got on free input pin on my LPT board. Is it possible to use it like that.

1. I would like to have one button on machine cassing that will do 2 things.
2. If machine is OFF, button will set machine to "on" mode
3. If machine is ON , then that button will will star the program "remrun"

Right now I have it like that, but I need to make it on one input pin :(

net remrun halui.mode.auto <= parport.0.pin-12-in
net remrun => halui.program.run
net machine-on <= parport.0.pin-15-in
net machine-on => halui.machine.on

Thanks in advance for help!

Best regards,
Czerech

Please Log in to join the conversation.

More
9 years 2 months ago #96983 by Todd Zuercher
Replied by Todd Zuercher on topic Assigning 2 funcitons to one button
This is something like what you will need to add to your hal file(s).
To use parallel port pin 15 for the on/run button.
Code:
loadrt oneshot count=1 loadrt and2 count=1 addf oneshot.0 servo-thread addf and2.0 servo-thread setp oneshot.0.rising false setp oneshot.0.falling true setp oneshot.0.width 2 net machine-on <= oneshot.0.out => halui.machine.on net machine-is-on <= halui.machine.is-on => and2.0.in0 #If halui.machine.is-on is already used somewhere just link this and2 to that signal. net on-run-btn <= parport.0.pin-15-innet => oneshot.0.in => and2.0.in1 net remrun <= and2.0.out => halui.mode.auto => halui.program.run

Please Log in to join the conversation.

More
9 years 2 months ago #96984 by Todd Zuercher
Replied by Todd Zuercher on topic Assigning 2 funcitons to one button
It is possible you may also need to debounce your parallel port input.

Please Log in to join the conversation.

More
9 years 2 months ago #96994 by czerech
Replied by czerech on topic Assigning 2 funcitons to one button
Thank you very much!!!!

I will test that next monday and let you know how did it go.

regards,
Piotr

Please Log in to join the conversation.

More
9 years 2 months ago #97133 by andypugh
Replied by andypugh on topic Assigning 2 funcitons to one button
There is also this HAL module. (does something a bit different to what you asked for, the and2 + oneshot way is better for what you asked for
linuxcnc.org/docs/2.7/html/man/man9/multiswitch.9.html
or
linuxcnc.org/docs/2.7/html/man/man9/multiclick.9.html

Please Log in to join the conversation.

More
9 years 2 months ago #97622 by czerech
Replied by czerech on topic Assigning 2 funcitons to one button
I didn't have time to check it :(
I'm going tommorow to do it, but I dont know if I added debounce properly.
Code:
loadrt debounce cfg="1" addf debounce.0 base-thread setp debounce.0.delay 10 loadrt oneshot count=1 loadrt and2 count=1 addf oneshot.0 servo-thread addf and2.0 servo-thread setp oneshot.0.rising false setp oneshot.0.falling true setp oneshot.0.width 2 net machine-on <= oneshot.0.out => halui.machine.on net machine-is-on <= halui.machine.is-on => and2.0.in0 net on-run-btn <= parport.0.pin-15-in => oneshot.0.in => and2.0.in1 net remrun <= and2.0.out => halui.mode.auto => halui.program.run net debounce-in <= parport.0.pin-15-in => debounce.0.0.in net debounce.0.0.out => oneshot.0.in net debounce.0.0.out => and2.0.in1

Please Log in to join the conversation.

Time to create page: 0.100 seconds
Powered by Kunena Forum