Mesa 7i43 (2port parallel) 400K with bitfile SVST2_4_7i47 using PnCConf

More
7 years 8 months ago #127257 by mane
Mesa 7i43 (2port parallel) 400K with bitfile SVST2_4_7i47 using PnCConf was created by mane
Hi,
i ordered a 7i43 card and want to use the pin file SVST2_4_7i47 because it fits best to my project.
Found some information here.
linuxcnc.org/docs/2.6/html/drivers/hostmot2.html

My system:
LinuxCNC/AXIS version 2.7.14
Linux linuxcnc 3.4-9-rtai-686-pae #1 SMP PREEMPT Debian 3.4.55-4linuxcnc i686 GNU/Linux

For testing purposes i used SVST4_4 to see if my card is working. And it is working.
In PnCConf is no SVST2_4_7i47 selectable. I downloaded 7i43.zip file from mesa.
Used the bit file "SVST2_4_7I47S.BIT" and copied it to /lib/firmware/hm2/7i43-4/
Copied the pin file "SVST2_4_7I47.PIN" to /usr/share/doc/hostmot2-firmware-7i43-4
But the file is not selectable in PnCConf.

Attachment not found



Is this the right bit file (4Encoder/2PWM/4StepGen/24GIPO) as discribed in the documentation above?
And what do i have to do to make this file selectable in PnCConf?

Many thanks
Manfred

Please Log in to join the conversation.

More
7 years 8 months ago #127259 by pl7i92
Replied by pl7i92 on topic Mesa 7i43 (2port parallel) 400K with bitfile SVST2_4_7i47 using PnCConf
loading the 7i43 with a 7i47 Bitfile is not in general a good idee as it is not build for this


pncconf does not automatic get the Bit and Pinfile
PLEASE ask cmorney if he got it inside
it is under constand Development

you can also ask in the Live Chatroom on IRC

PCW will help you Calafornia Timezone

Please Log in to join the conversation.

More
7 years 8 months ago #127264 by andypugh
Replied by andypugh on topic Mesa 7i43 (2port parallel) 400K with bitfile SVST2_4_7i47 using PnCConf

pl7i92 wrote: loading the 7i43 with a 7i47 Bitfile is not in general a good idee as it is not build for this


The 7i47 is just a 50-pin daughter card. There is no reason that it wouldn't work perfectly well with the 7i43.

Please Log in to join the conversation.

More
7 years 8 months ago #127278 by PCW
Replied by PCW on topic Mesa 7i43 (2port parallel) 400K with bitfile SVST2_4_7i47 using PnCConf
I dont think pncconf supports that configuration but you can use pncconf to create a working
hal/ini file set for a similar configuration (say SVST4_4) and edit the hal file to make any 7I47 specific changes.

Note that since stepgens, pwmgens, and encoder hardware is accessed in hal by number, not pin, there is very little difference in configurations for different daughtercards that have have basic stepgens, encoders, pwmgens etc

Please Log in to join the conversation.

More
7 years 8 months ago #127288 by mane
Replied by mane on topic Mesa 7i43 (2port parallel) 400K with bitfile SVST2_4_7i47 using PnCConf

PCW wrote: I dont think pncconf supports that configuration but you can use pncconf to create a working
hal/ini file set for a similar configuration (say SVST4_4) and edit the hal file to make any 7I47 specific changes.

Note that since stepgens, pwmgens, and encoder hardware is accessed in hal by number, not pin, there is very little difference in configurations for different daughtercards that have have basic stepgens, encoders, pwmgens etc


I don´t really understand, sorry.
Let´s say i use SVST4_4 configuration and use only 1Encoder, 1PWM, 4StepGen. Will this result in some GPIO?

Please Log in to join the conversation.

More
7 years 8 months ago #127294 by PCW
Replied by PCW on topic Mesa 7i43 (2port parallel) 400K with bitfile SVST2_4_7i47 using PnCConf
The hal setup for the stepgens and PWMs and encoders would be the same for any Mesa
FPGA card or firmware. The only difference would be any GPIO pins used as plain GPIO,
or inversion of PWM/Stepgen pins referenced by GPIO pin number (and the base FPGA card name)

That is if you just have 1 PWM generator, its always going to be referred to as PWM 0
in the hal file not by the pins its connected to.
Likewise, if you have 4 Stepgens, they will be accessed in hal as stepgen 0 to stepgen 3

Please Log in to join the conversation.

More
7 years 8 months ago #127352 by mane
Replied by mane on topic Mesa 7i43 (2port parallel) 400K with bitfile SVST2_4_7i47 using PnCConf
Today i tried to make a very basic configuration with PnCConf.
Used SVST4_4 bitfile and created only 3 step generators. On the tabs for IO connector 3 and 4 i have now many unused inputs.
After starting my configuration i listed the pinout with
Code:
sudo mesaflash --device 7i43 --epp --addr 0x378 --readhmid

But the pins are not as expected. There are PWM, Encoder but no GIPO.
Code:
manfred@linuxcnc:~$ sudo mesaflash --device 7i43 --epp --addr 0x378 --readhmid Configuration Name: HOSTMOT2 General configuration information: BoardName : MESA7I43 FPGA Size: 400 KGates FPGA Pins: 144 Number of IO Ports: 2 Width of one I/O port: 24 Clock Low frequency: 50.0000 MHz Clock High frequency: 100.0000 MHz IDROM Type: 3 Instance Stride 0: 4 Instance Stride 1: 64 Register Stride 0: 256 Register Stride 1: 256 Modules in configuration: Module: WatchDog There are 1 of WatchDog in configuration Version: 0 Registers: 3 BaseAddress: 0C00 ClockFrequency: 50.000 MHz Register Stride: 256 bytes Instance Stride: 4 bytes Module: IOPort There are 2 of IOPort in configuration Version: 0 Registers: 5 BaseAddress: 1000 ClockFrequency: 50.000 MHz Register Stride: 256 bytes Instance Stride: 4 bytes Module: QCount There are 4 of QCount in configuration Version: 2 Registers: 5 BaseAddress: 3000 ClockFrequency: 50.000 MHz Register Stride: 256 bytes Instance Stride: 4 bytes Module: PWM There are 4 of PWM in configuration Version: 0 Registers: 5 BaseAddress: 4000 ClockFrequency: 100.000 MHz Register Stride: 256 bytes Instance Stride: 4 bytes Module: StepGen There are 4 of StepGen in configuration Version: 2 Registers: 10 BaseAddress: 2000 ClockFrequency: 50.000 MHz Register Stride: 256 bytes Instance Stride: 4 bytes Module: AddrX There are 1 of AddrX in configuration Version: 0 Registers: 4 BaseAddress: 7800 ClockFrequency: 50.000 MHz Register Stride: 256 bytes Instance Stride: 4 bytes Module: LED There are 1 of LED in configuration Version: 0 Registers: 1 BaseAddress: 0200 ClockFrequency: 50.000 MHz Register Stride: 256 bytes Instance Stride: 4 bytes Configuration pin-out: IO Connections for P4 Pin# I/O Pri. func Sec. func Chan Pin func Pin Dir 1 0 IOPort QCount 1 Quad-B (In) 3 1 IOPort QCount 1 Quad-A (In) 5 2 IOPort QCount 0 Quad-B (In) 7 3 IOPort QCount 0 Quad-A (In) 9 4 IOPort QCount 1 Quad-IDX (In) 11 5 IOPort QCount 0 Quad-IDX (In) 13 6 IOPort PWM 1 PWM (Out) 15 7 IOPort PWM 0 PWM (Out) 17 8 IOPort PWM 1 Dir (Out) 19 9 IOPort PWM 0 Dir (Out) 21 10 IOPort PWM 1 /Enable (Out) 23 11 IOPort PWM 0 /Enable (Out) 25 12 IOPort QCount 3 Quad-B (In) 27 13 IOPort QCount 3 Quad-A (In) 29 14 IOPort QCount 2 Quad-B (In) 31 15 IOPort QCount 2 Quad-A (In) 33 16 IOPort QCount 3 Quad-IDX (In) 35 17 IOPort QCount 2 Quad-IDX (In) 37 18 IOPort PWM 3 PWM (Out) 39 19 IOPort PWM 2 PWM (Out) 41 20 IOPort PWM 3 Dir (Out) 43 21 IOPort PWM 2 Dir (Out) 45 22 IOPort PWM 3 /Enable (Out) 47 23 (unknown-gtag) (unknown-gtag) Global Unknown (Out) IO Connections for P3 Pin# I/O Pri. func Sec. func Chan Pin func Pin Dir 1 24 IOPort StepGen 0 Step/Table1 (Out) 3 25 IOPort StepGen 0 Dir/Table2 (Out) 5 26 IOPort StepGen 0 Table3 (Out) 7 27 IOPort StepGen 0 Table4 (Out) 9 28 IOPort StepGen 0 Table5 (Out) 11 29 IOPort StepGen 0 Table6 (Out) 13 30 IOPort StepGen 1 Step/Table1 (Out) 15 31 IOPort StepGen 1 Dir/Table2 (Out) 17 32 IOPort StepGen 1 Table3 (Out) 19 33 IOPort StepGen 1 Table4 (Out) 21 34 IOPort StepGen 1 Table5 (Out) 23 35 IOPort StepGen 1 Table6 (Out) 25 36 IOPort StepGen 2 Step/Table1 (Out) 27 37 IOPort StepGen 2 Dir/Table2 (Out) 29 38 IOPort StepGen 2 Table3 (Out) 31 39 IOPort StepGen 2 Table4 (Out) 33 40 IOPort StepGen 2 Table5 (Out) 35 41 IOPort StepGen 2 Table6 (Out) 37 42 IOPort StepGen 3 Step/Table1 (Out) 39 43 IOPort StepGen 3 Dir/Table2 (Out) 41 44 IOPort StepGen 3 Table3 (Out) 43 45 IOPort StepGen 3 Table4 (Out) 45 46 (unknown-gtag) (unknown-gtag) Global Unknown (Out) 47 47 IOPort StepGen 3 Table6 (Out)

Attachment not found

Please Log in to join the conversation.

More
7 years 8 months ago #127354 by PCW
Replied by PCW on topic Mesa 7i43 (2port parallel) 400K with bitfile SVST2_4_7i47 using PnCConf
That's expected, notice the first column ( Pri. func ) in mesaflashes pin list? ( IOPort )
All pins are available as GPIO if they are not claimed by an _enabled_ secondary function (Sec. func)

Edit
Also you should not run mesaflash when LinuxCNC is running ( notice the bad data on GPIO23?, this is likely due to a access collision )
To check available hardware pins, run

halcmd show pin hm2*
or
for gpio:
halcmd show pin *gpio*

Please Log in to join the conversation.

More
7 years 8 months ago #127356 by andypugh
Replied by andypugh on topic Mesa 7i43 (2port parallel) 400K with bitfile SVST2_4_7i47 using PnCConf

mane wrote: Today i tried to make a very basic configuration with PnCConf.
Used SVST4_4 bitfile and created only 3 step generators. On the tabs for IO connector 3 and 4 i have now many unused inputs.
After starting my configuration i listed the pinout with

Code:
sudo mesaflash --device 7i43 --epp --addr 0x378 --readhmid


Mesaflash lists the firmware pinout, not the pinout that is active in your configuration.

If you start LinuxCNC from the command line you should get the actual pinout that your config is using listed on the screen.

Please Log in to join the conversation.

More
7 years 7 months ago #127439 by mane
Replied by mane on topic Mesa 7i43 (2port parallel) 400K with bitfile SVST2_4_7i47 using PnCConf

andypugh wrote: Mesaflash lists the firmware pinout, not the pinout that is active in your configuration.

If you start LinuxCNC from the command line you should get the actual pinout that your config is using listed on the screen.


Tried to start from command line, but nothing listed on the screen.
Code:
manfred@linuxcnc:~/linuxcnc/configs/7i43$ linuxcnc 7i43.ini LINUXCNC - 2.7.14 Machine configuration directory is '/home/manfred/linuxcnc/configs/7i43' Machine configuration file is '7i43.ini' Running HAL shutdown script Starting LinuxCNC... . Found file(REL): ./7i43.hal Found file(REL): ./custom.hal

Please Log in to join the conversation.

Time to create page: 0.100 seconds
Powered by Kunena Forum