Optiplex 755

More
3 years 7 months ago #266055 by zz912
Replied by zz912 on topic Optiplex 755
Code:
jarda@CNC1:~$ sudo chrt 99 ping -i .001 -q 10.10.10.10 PING 10.10.10.10 (10.10.10.10) 56(84) bytes of data. ^C --- 10.10.10.10 ping statistics --- 253024 packets transmitted, 253023 received, 0.000395219% packet loss, time 276ms rtt min/avg/max/mdev = 0.164/0.253/0.539/0.012 ms jarda@CNC1:~$

I have to go home right now. I can do more tests tomorrow.
 

Please Log in to join the conversation.

More
3 years 7 months ago #266093 by zz912
Replied by zz912 on topic Optiplex 755
Optiplex 7010
I made same test with Optiplex 7010 at home.
 

Attachment not found


 

Attachment not found


Coalescing Disabled
It is better, but first test is wrong too.
 

Please Log in to join the conversation.

More
3 years 7 months ago #266185 by zz912
Replied by zz912 on topic Optiplex 755
I would like to ask what these tests mean? Do I have a weak PC? Or is there a bug somewhere (LCNC, kernel, debian ....)?

Please Log in to join the conversation.

More
3 years 7 months ago #266200 by rodw
Replied by rodw on topic Optiplex 755
try this command
Code:
latency-histogram --nobase --sbins 1000
as PCW said there is no need to look at the base thread as it is not used with a mesa card.

the histogram shows the jitter which is the time a thread is late or early. If there is too much jitter, the servo-thread will not get finished before the next one starts... which is a latency error...

Please Log in to join the conversation.

More
3 years 7 months ago #266205 by zz912
Replied by zz912 on topic Optiplex 755
1) I understand, that I can ignore Base thread. I didn't realize that 25000 in the error message means that the error is in basethread and not in servothead.

2) My main question is, can I ignore the PC test in the MesaCT configurator?
 

Attachment not found



3) I will try latency-histogram
 

Please Log in to join the conversation.

More
3 years 7 months ago #266214 by PCW
Replied by PCW on topic Optiplex 755
I think there is a bug in mesact

The servo thread tmax should show 75%

(100*1747291/2333333)

If you have disabled all power saving options in the CPU
and have Interrupt coalescing off you may have to run at a lower
servo thread rate on that PC (say 2 ms period instead of 1 ms)

Please Log in to join the conversation.

More
3 years 7 months ago #266217 by zz912
Replied by zz912 on topic Optiplex 755
I had 3 problems:
1) MesaCT - I'm going to assume it's wrong.
2) Latency message error - now I know, that it is BaseThread
3) SSerial error - Maybe turning off the AMT setup will help. I will keep an eye out to see if the error reappears.

Please Log in to join the conversation.

More
3 years 7 months ago #266298 by zz912
Replied by zz912 on topic Optiplex 755
Yesterday I celebrated that turning off AMT solved my problem. Today I came to the PC and again it is causing problems.
 

Attachment not found

Please Log in to join the conversation.

More
3 years 7 months ago #266300 by PCW
Replied by PCW on topic Optiplex 755
I would try a 2 ms servo thread period

Please Log in to join the conversation.

More
3 years 7 months ago #266307 by zz912
Replied by zz912 on topic Optiplex 755
2 ms did not help:
 

Attachment not found



Mabey evengravy have solution:
forum.linuxcnc.org/38-general-linuxcnc-q...2-8-4-stretch#266292

It's strange that I had no problems yesterday.

Please Log in to join the conversation.

Time to create page: 0.060 seconds
Powered by Kunena Forum