hi all,
after i worked over a year with my Milling machine with linuxCNC, no i will do an Upgrade and like to install a laser-Module.
A year ago, when i installed my Computer (DELL Optiplex 790) i installed 2 of SUNIX Co., Ltd. Multiport serial controller.
Together with my StepMax4 Box i always used only one of this controller and every works fine.
Now i have to use both of this controller cards and it woun`t work.
I tested some things (I do not have much knowlede about Ubuntu)
If i do the "lspci -v" i get the following information:
Code:
00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09)
Subsystem: Dell 2nd Generation Core Processor Family DRAM Controller
Flags: bus master, fast devsel, latency 0
Capabilities: <access denied>
Kernel driver in use: snb_uncore
00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 16
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00004000-00004fff
Capabilities: <access denied>
Kernel driver in use: pcieport
00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) (prog-if 00 [VGA controller])
Subsystem: Dell 2nd Generation Core Processor Family Integrated Graphics Controller
Flags: bus master, fast devsel, latency 0, IRQ 26
Memory at e0c00000 (64-bit, non-prefetchable) [size=4M]
Memory at d0000000 (64-bit, prefetchable) [size=256M]
I/O ports at 5000 [size=64]
[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: i915
Kernel modules: i915
00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04)
Subsystem: Dell 6 Series/C200 Series Chipset Family MEI Controller
Flags: bus master, fast devsel, latency 0, IRQ 27
Memory at e1ab0000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: mei_me
Kernel modules: mei_me
00:19.0 Ethernet controller: Intel Corporation 82579LM Gigabit Network Connection (rev 04)
Subsystem: Dell 82579LM Gigabit Network Connection (Lewisville)
Flags: bus master, fast devsel, latency 0, IRQ 24
Memory at e1a00000 (32-bit, non-prefetchable) [size=128K]
Memory at e1a80000 (32-bit, non-prefetchable) [size=4K]
I/O ports at 5080 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
Kernel modules: e1000e
00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 04) (prog-if 20 [EHCI])
Subsystem: Dell 6 Series/C200 Series Chipset Family USB Enhanced Host Controller
Flags: bus master, medium devsel, latency 0, IRQ 16
Memory at e1a70000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 04)
Subsystem: Dell 6 Series/C200 Series Chipset Family High Definition Audio Controller
Flags: bus master, fast devsel, latency 0, IRQ 28
Memory at e1a60000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b4) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 16
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b4) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 18
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: e1000000-e19fffff
Prefetchable memory behind bridge: 00000000e0000000-00000000e09fffff
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.4 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 (rev b4) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 16
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 00002000-00002fff
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 04) (prog-if 20 [EHCI])
Subsystem: Dell 6 Series/C200 Series Chipset Family USB Enhanced Host Controller
Flags: bus master, medium devsel, latency 0, IRQ 17
Memory at e1a50000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a4) (prog-if 01 [Subtractive decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
Capabilities: <access denied>
00:1f.0 ISA bridge: Intel Corporation Q65 Express Chipset Family LPC Controller (rev 04)
Subsystem: Dell Q65 Express Chipset LPC Controller
Flags: bus master, medium devsel, latency 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
Kernel modules: lpc_ich
00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family SATA AHCI Controller (rev 04) (prog-if 01 [AHCI 1.0])
Subsystem: Dell 6 Series/C200 Series Chipset Family 6 port Desktop SATA AHCI Controller
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 25
I/O ports at 50d0 [size=8]
I/O ports at 50c0 [size=4]
I/O ports at 50b0 [size=8]
I/O ports at 50a0 [size=4]
I/O ports at 5060 [size=32]
Memory at e1a40000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 04)
Subsystem: Dell 6 Series/C200 Series Chipset Family SMBus Controller
Flags: medium devsel, IRQ 18
Memory at e1a30000 (64-bit, non-prefetchable) [size=256]
I/O ports at 5040 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c_i801
01:00.0 Parallel controller: SUNIX Co., Ltd. Multiport serial controller (prog-if 03 [IEEE1284])
Subsystem: SUNIX Co., Ltd. Multiport serial controller
Flags: bus master, fast devsel, latency 0, IRQ 11
I/O ports at 4030 [size=8]
I/O ports at 4020 [size=8]
I/O ports at 4000 [size=32]
Capabilities: <access denied>
04:00.0 Parallel controller: SUNIX Co., Ltd. Multiport serial controller (prog-if 03 [IEEE1284])
Subsystem: SUNIX Co., Ltd. Multiport serial controller
Flags: bus master, fast devsel, latency 0, IRQ 11
I/O ports at 2030 [size=8]
I/O ports at 2020 [size=8]
I/O ports at 2000 [size=32]
Capabilities: <access denied>
So at the end these 2 Parallel controller uses the same IRQ.
If i test "halrun -I -f ptest.hal" (after I updates the i/o Port-Information)
I can, for example switch an relais, but if i try to work with both at the same time, it woun`t work.
If I update the ptest.hal to work with both i get an error:
Code:
No parport registered at 0x2030. This is not always an error. Continuing.
No parport registered at 0xffff. This is not always an error. Continuing.
the error about 0x2030 i get allways, but it will work.
But i dont know what is about 0xffff..
Ist there an option to change the IRQ manualy?
Many thanks and best regards
Jens
