Chinese Mesa 7I92 from aliexpress NEW

It may be that the Fujitsu Mini PC (like many laptops) has some
built-in power management that cannot be disabled.

 

PCW wrote:

If they did supply firmware, I would try re-writing it with:

mesaflash --device 7i92 --addr 10.10.10.10 --write  vendor_supplied_firmware_file_name.bit --reload

 

My Chinese 7i98 doesn't seem to have a fallback area, so I bricked one of mine by flashing a corrupted Chinese firmware. I wouldn't try again to flash it this way.

Since then I am doing it the Chinese way:

sudo mesaflash --device 7i92 --addr 192.168.1.121 --write 7i92.bit --fix --fallback
sudo mesaflash --device 7i92 --addr 192.168.1.121 --write 7i92.bit --fallback
sudo mesaflash --device 7i92 --addr 192.168.1.121 --reload --fallback

If the firmware doesn't work, it says: "No 7I98 board found" and only one LED is on.  So I know if the firmware is bad and I don't go further. After power cycling it, the previous firmware is loaded and it works again.

If it works (and only if it works), i continue with:

sudo mesaflash --device 7i92 --addr 192.168.1.121 --write 7i92.bit --fix  
sudo mesaflash --device 7i92 --addr 192.168.1.121 --write 7i92.bit  
sudo mesaflash --device 7i92 --addr 192.168.1.121 --reload

Then I power cycle it and check the pins:

sudo mesaflash --device 7i92 --addr 192.168.1.121 --readhmid

I've tested some original 7i92 and 7i98 bitfiles and they all work perfectly, so there is no point in using Chinese bitfiles except if the "7i92" card doesn't even look like a Mesa card and really needs a Chinese custom file. I believe, even the files supplied by the Chinese are mostly original files.

I also could flash a Chinese 7i98 fallback firmware called "7i92_fallback.bit" on a Chinese 7i92, so the 7i92 had 50 pins.
But it didn't brick, so I could flash the right firmware afterwards.




 

On Xilinx based cards you can use any working bitfile for fallback.
It wont have the blinking INIT LED indicator but otherwise the same.

This will protect against things like a power failure during flash update
It will not protect against writing firmware that does not work but has a
valid chip type and CRC (like firmware for a different card)

If you do have working fallback and a bad primary (Good CRC but does not work),
it is possible to recover without JTAG by intentionally causing an error in the primary
flash file load (say by shorting out the flash chip SDO pin briefly at power up)

Thank you for the reply, but I just flashed at least the 3.3V power regulator with 24V on the still working 7i98 instead, so it will take some time for me to do the repair. Maybe I can even program it using raspberry GPIOs then.
By that coincidence I had an EEPROM with a working firmware, which I just soldered it on the bricked card. Now it works again, but the other one doesn't.

Ok. got it to work with the intel itx board. the fujistu minipc is hopeless.
I got it with 7i92_G540x2D firmware, kind of weird to setup the pins. Is there a simple firmware?
For reference i'm planning to use an lathe like 400x1000 3 tons with live tooling so no Y axis (X axis, Z axis and C-axis)

Edit: BTW i used a chinese usb stick (USB 3.0) and when i install the linuxcnc it gave errors (like the password for the wifi did not work or it refuse to install grub loader, so i use another usb and it works like charm).

With a 7I92, you would normally chose firmware that matches the
pinout of the breakout board you use. The G540x2 firmware is made
to match the pinout of the Gecko G540 4 Axis step/dir drive.

A commonly use breakout board (BOB)  is the Sainsmart "Mach 5 Axis CNC" breakout
For the, you would use  "5ABOB" firmware

youre right about the bob, but for now i dont have a bob.
For now i'm new to mesa card in general.
Thanks

I would like to apologise to the OP for my remarks to his original post.

I have been shown to be unkind and unhelpful. My fellow forum members have been very gracious.

Aqui os 3 modelos que testei funcionaram bem.
Mas com .bit chinês

Witam kupiłem taką samą kartę i czekam na przesyłkę.
Moje pytanie to jakim napięciem zasilasz tą kartę , w opisie podają 24V max i czy tylko to wystarczy ?