MAC address not retrieved (after 2 years stop)

More
9 months 1 week ago #341842 by Jocman
Replied by Jocman on topic MAC address not retrieved (after 2 years stop)
Now the linuxcnc error is once again about the mac address (as in my first post)
Then, I tried to install the drivers for the lan card as you suggest, but this is what I get:
Code:
joccnc@JocCnc:~$ sudo apt install r8168-dkms [sudo] password for joccnc: Reading package lists... Done Building dependency tree        Reading state information... Done E: Unable to locate package r8168-dkms

and trying to follow your tutorial on youtube, as soon as I try to install grub-customizer (at the very beginning of the tutorial) I get this:
Code:
joccnc@JocCnc:~$ sudo apt install grub-customizer geany [sudo] password for joccnc: Reading package lists... Done Building dependency tree        Reading state information... Done E: Unable to locate package grub-customizer joccnc@JocCnc:~$

Please Log in to join the conversation.

More
9 months 1 week ago #341844 by rodw
Replied by rodw on topic MAC address not retrieved (after 2 years stop)
this is a bit tricky because you need non-free in your sources. This is included in our ISO
skip geub-customizer for now

Please Log in to join the conversation.

More
9 months 6 days ago #341858 by tommylight
Replied by tommylight on topic MAC address not retrieved (after 2 years stop)
Do a
Code:
sudo apt update
before trying to install something, then
Code:
sudo apt install r8168-dkms

Please Log in to join the conversation.

More
9 months 5 days ago #341922 by Jocman
Replied by Jocman on topic MAC address not retrieved (after 2 years stop)
I've tried to update the system, but I get this:
Code:
joccnc@JocCnc:~$ sudo apt update [sudo] password for joccnc: Sorry, try again. [sudo] password for joccnc: Ign:1 http://linuxcnc.org stretch InRelease Err:2 http://linuxcnc.org stretch Release Cannot initiate the connection to linuxcnc.org:80 (69.163.143.134). - connect (101: Network is unreachable) Ign:3 http://security.debian.org/debian-security stretch/updates InRelease Err:4 http://security.debian.org/debian-security stretch/updates Release 404 Not Found [IP: 151.101.2.132 80] Ign:5 http://ftp.debian.org/debian stretch InRelease Err:6 http://ftp.debian.org/debian stretch Release 404 Not Found [IP: 146.75.62.132 80] Reading package lists... Done E: The repository 'http://linuxcnc.org stretch Release' does no longer have a Release file. N: Updating from such a repository can't be done securely, and is therefore disabled by default. N: See apt-secure(8) manpage for repository creation and user configuration details. E: The repository 'http://security.debian.org/debian-security stretch/updates Release' does no longer have a Release file. N: Updating from such a repository can't be done securely, and is therefore disabled by default. N: See apt-secure(8) manpage for repository creation and user configuration details. E: The repository 'http://ftp.debian.org/debian stretch Release' does no longer have a Release file. N: Updating from such a repository can't be done securely, and is therefore disabled by default. N: See apt-secure(8) manpage for repository creation and user configuration details.

As I can understand, there's something wrong (it seems almost...impossible to not find anything. Windows maybe, but Linux.....): too old version (2.7.14)???.
Anyway, I'm a little bit demoralized...
2 years ago I made the last job (a double sided PCB) and everything was perfect, then shutdown the system.
I can't understand what happened.
Before keeping going on with making you waste your time (I don't want it), as per your experience my problems can be related to:
1) software (linuxcnc) failure?
2) Mesa board failure?
3) MB failure?

In case 1), if I install the last linuxcnc release, will it be any chance to retrieve my current setup and customization (hoping it can fix the current problem)? 4 years ago I've spent almost 4-5 months to set linuxcnc (and with your needfull support, by myself I can't do anything....) and customize my axis with the function I normally use, so lose everything is something I don't want to....

Anyway, please tell me your opinion, I'll follow your suggestions.

Please Log in to join the conversation.

More
9 months 5 days ago #341925 by rodw
Replied by rodw on topic MAC address not retrieved (after 2 years stop)
Looks like you've lost your network. what does ip a say?
Look to make sure you have an IP address on your network side 
can you ping your router?

Please Log in to join the conversation.

More
9 months 4 days ago #341958 by Jocman
Replied by Jocman on topic MAC address not retrieved (after 2 years stop)
I don't think I've lost the network.
I've selected the pci card to connect to my network (in fact, I can normally access internet).
BTW, this evening (here's almost 6 pm) I hope to make another try (if my wife allow me 
[img
)

Please Log in to join the conversation.

More
9 months 4 days ago #341960 by tommylight
Replied by tommylight on topic MAC address not retrieved (after 2 years stop)
Rod asked you to post the result of
Code:
ip a
in a terminal.

Please Log in to join the conversation.

More
9 months 3 days ago #342013 by Jocman
Replied by Jocman on topic MAC address not retrieved (after 2 years stop)
As I've 2 lan cards (the onboard and a second PCI board), I tried to launch
Code:
ip a
when connected to both, and this is what I get:
connected to Mesa (onboard card):
Code:
joccnc@JocCnc:~$ ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00     inet 127.0.0.1/8 scope host lo        valid_lft forever preferred_lft forever     inet6 ::1/128 scope host        valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000     link/ether e8:4e:06:84:dc:c9 brd ff:ff:ff:ff:ff:ff     inet 10.10.10.11/8 brd 10.255.255.255 scope global eth0        valid_lft forever preferred_lft forever     inet6 fd59:b8bd:be6f:0:377f:d68c:ef9e:9227/64 scope global noprefixroute dynamic        valid_lft 7154sec preferred_lft 3554sec     inet6 fe80::8bdd:424d:f6d4:7ea2/64 scope link        valid_lft forever preferred_lft forever 3: eth1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN group default qlen 1000     link/ether 70:85:c2:6a:f0:3d brd ff:ff:ff:ff:ff:ff joccnc@JocCnc:~$
and pinging  my router:
Code:
joccnc@JocCnc:~$ ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1): 56 data bytes ping: sending packet: Network is unreachable


connected to WEB:
Code:
joccnc@JocCnc:~$ ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00     inet 127.0.0.1/8 scope host lo        valid_lft forever preferred_lft forever     inet6 ::1/128 scope host        valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000     link/ether e8:4e:06:84:dc:c9 brd ff:ff:ff:ff:ff:ff     inet 192.168.1.245/24 brd 192.168.1.255 scope global dynamic eth0        valid_lft 863814sec preferred_lft 863814sec     inet6 fd59:b8bd:be6f:0:6bdd:2ca7:6e73:aa7b/64 scope global noprefixroute dynamic        valid_lft 7016sec preferred_lft 3416sec     inet6 fe80::6ed6:c856:a0cb:2db8/64 scope link        valid_lft forever preferred_lft forever 3: eth1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN group default qlen 1000     link/ether 70:85:c2:6a:f0:3d brd ff:ff:ff:ff:ff:ff joccnc@JocCnc:~$
and pinging my router:
Code:
joccnc@JocCnc:~$ ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1): 56 data bytes 64 bytes from 192.168.1.1: icmp_seq=0 ttl=64 time=0.651 ms 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=0.488 ms 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=0.479 ms 64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=0.522 ms 64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=0.479 ms 64 bytes from 192.168.1.1: icmp_seq=5 ttl=64 time=0.461 ms 64 bytes from 192.168.1.1: icmp_seq=6 ttl=64 time=0.479 ms 64 bytes from 192.168.1.1: icmp_seq=7 ttl=64 time=0.478 ms 64 bytes from 192.168.1.1: icmp_seq=8 ttl=64 time=0.483 ms 64 bytes from 192.168.1.1: icmp_seq=9 ttl=64 time=0.486 ms 64 bytes from 192.168.1.1: icmp_seq=10 ttl=64 time=0.398 ms

I've attached a screenshot of my desktop showing the lan connection window

Please Log in to join the conversation.

More
9 months 3 days ago #342033 by tommylight
Replied by tommylight on topic MAC address not retrieved (after 2 years stop)
You have setup 2 networks on the same 1'st physical network card, the 2'nd network card has nothing set.
WHY????
That will not work, so start new and use this:
forum.linuxcnc.org/27-driver-boards/3559...ethernet-mesa-boards

Please Log in to join the conversation.

More
9 months 3 days ago #342060 by NWE
Replied by NWE on topic MAC address not retrieved (after 2 years stop)

Code:
[code]2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000     link/ether e8:4e:06:84:dc:c9 brd ff:ff:ff:ff:ff:ff     inet 10.10.10.11/8 brd 10.255.255.255 scope global eth0 and: [code][code]2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000     link/ether e8:4e:06:84:dc:c9 brd ff:ff:ff:ff:ff:ff     inet 192.168.1.245/24 brd 192.168.1.255 scope global dynamic eth0  
[/code][/code][/code]

 
Just to clarify, do you have everything connected to the router? Or did you have just the Mesa card plugged in the first time, then just the router, the second time?

You will likely get better performance connecting one network cable directly from Mesa card to the first network port on the pc, then another network cable from your router to the second network port on the pc. Then you can choose eth1 for your web connection.

Please Log in to join the conversation.

Time to create page: 0.070 seconds
Powered by Kunena Forum