2 seperate MPG handwheels for each axis - CNC Lathe build

More
6 years 5 months ago #168044 by denhen89
Replied by denhen89 on topic 2 seperate MPG handwheels for each axis - CNC Lathe build
@Rodw: Of course i understand to find out a lot of things by my self, but i really tried but its difficult for me.
Thanks for "setp axis.x.jog-scale 1", but if in Halmeter nothing happens when turning the handwheel, then i think that the problem might be in the wiring, or am i wrong ?

Please Log in to join the conversation.

More
6 years 5 months ago #168045 by rodw
Replied by rodw on topic 2 seperate MPG handwheels for each axis - CNC Lathe build
Can you chexk what I used here
Code:
sserial_port_0=200xxxx

I have a feeling I might have been different.

If the mode is right and it is not counting, then look at wiring.

Please Log in to join the conversation.

More
6 years 5 months ago #168046 by denhen89
Replied by denhen89 on topic 2 seperate MPG handwheels for each axis - CNC Lathe build
I have tried: sserial_port_0=200xxxx
nothing happens on halmeter.

Please Log in to join the conversation.

More
6 years 5 months ago #168047 by tommylight
Replied by tommylight on topic 2 seperate MPG handwheels for each axis - CNC Lathe build
The wiring is OK, on TB5.
Edited, wrong info removed.

Please Log in to join the conversation.

More
6 years 5 months ago #168048 by tommylight
Replied by tommylight on topic 2 seperate MPG handwheels for each axis - CNC Lathe build
The blue and white wire.

Please Log in to join the conversation.

More
6 years 5 months ago #168049 by denhen89
Replied by denhen89 on topic 2 seperate MPG handwheels for each axis - CNC Lathe build
Okay, i will test it, but on this manual: wiki.eusurplus.com/downloads/7i76E.pdf
on page: Connection of MPG's, it shows that i should connect it to TB5

Please Log in to join the conversation.

More
6 years 5 months ago #168050 by denhen89
Replied by denhen89 on topic 2 seperate MPG handwheels for each axis - CNC Lathe build
Still not showing anything on Halmeter

Please Log in to join the conversation.

More
6 years 5 months ago #168051 by tommylight
Replied by tommylight on topic 2 seperate MPG handwheels for each axis - CNC Lathe build

denhen89 wrote: Okay, i will test it, but on this manual: wiki.eusurplus.com/downloads/7i76E.pdf
on page: Connection of MPG's, it shows that i should connect it to TB5

Yes it does, leme check again.
Back in a few.

Please Log in to join the conversation.

More
6 years 5 months ago #168052 by tommylight
Replied by tommylight on topic 2 seperate MPG handwheels for each axis - CNC Lathe build
Yes they should be on TB5, my bad, was thinking of analog inputs somehow.
Can you also check encoder.1 with hal meter ?

Please Log in to join the conversation.

More
6 years 5 months ago #168053 by denhen89
Replied by denhen89 on topic 2 seperate MPG handwheels for each axis - CNC Lathe build
Works!
What i did. I took the second MPG handwheel i had lying around and connected all 4 wires to the terminals but without the resistors. Halmeter shows counts!

EDIT: and of course i changed the white and blue wire back to TB5

Please Log in to join the conversation.

Time to create page: 0.070 seconds
Powered by Kunena Forum