( Solved ) Issues with python plugin for remap

Bevins, I have no idea about toolchangers except that I've seen many echo your last sentiments. :sick:
I still don't know where the oword procedures live. Can you enlighten me?

I know sometimes the sims have symbolic links that don't get copied over but I could not see any in the rack changer

rodw wrote: Bevins, I have no idea about toolchangers except that I've seen many echo your last sentiments. :sick:
I still don't know where the oword procedures live. Can you enlighten me?

I know sometimes the sims have symbolic links that don't get copied over but I could not see any in the rack changer

They live in the nc_subroutines directory where ever you put it in the ini file.

See if this helps:
forum.linuxcnc.org/38-general-linuxcnc-q...l-change-setup#94222
forum.linuxcnc.org/20-g-code/36441-anyon...-length-probe#131714
forum.linuxcnc.org/49-basic-configuratio...-tool-changer#149789
Just in case you missed them.

Bevins, when I looked at the folder in github,
github.com/LinuxCNC/linuxcnc/tree/master...emap/rack-toolchange
it referred to this wiki page
wiki.linuxcnc.org/cgi-bin/wiki.pl?RackToolChanger

I think you need to add the parameters under heading 3 to your ini file.

Do that and see how you go then...

rodw wrote: Bevins, when I looked at the folder in github,
github.com/LinuxCNC/linuxcnc/tree/master...emap/rack-toolchange
it referred to this wiki page
wiki.linuxcnc.org/cgi-bin/wiki.pl?RackToolChanger

I think you need to add the parameters under heading 3 to your ini file.

Do that and see how you go then...

I don't think they use that any,more but I tried it and its the same thing. I am beginning to think it is a python issue with linux mint 18.3.

Anyone using oword ngc m6 remap with Linux Mint 18.3

Or something changed in 2,9 pre

Here is my rack_change.ngc

So there is basically nothing in it. It does do the print statement but never continues on like it didn't run the epilog, which is a python thing,,,,.. WTF am I missing?

I put print statements in the change_prolog and change epilog and they didn't print. I don't think it is running stdglue.

OK so it is running prolog as I suspected because of print statement in rack_change.ngc and it prints Entering Prolog print statement I put in there but it never runs change_epilog.

Can someone else verify this?

I suspect this might be a bug and/or a regression possibly due to the roll out of Python 3.

There have been some bug fixes in the past around this. See
github.com/LinuxCNC/linuxcnc/issues/217
I also looked at some of the cross referenced issues.
Is it an issue in Master branch?

Now you've diagnosed that its a coding fault (procedure not called), I think you should log a bug report..

rodw wrote: I suspect this might be a bug and/or a regression possibly due to the roll out of Python 3.

There have been some bug fixes in the past around this. See
github.com/LinuxCNC/linuxcnc/issues/217
I also looked at some of the cross referenced issues.
Is it an issue in Master branch?

Now you've diagnosed that its a coding fault (procedure not called), I think you should log a bug report..

I am trying to make sure it is not an issue I caused with config. But I have exhausted all possibilities. I even reinstalled via debs the latest 2.9. Still same issue.

I am also getting this when I load linuxcnc with remap M6 enabled.

I dont know what this means....lol



I put prtint statements in prolog and epilog and in ngc file. It prints the statement prolog and ngc file but never hits epilog.