Hi,
Im trying to configure vfd to mesa TB4.
I have connected as follows:
7I76 TB4 VFD
1 SPINDLE- ==> AI1 COMMON GND
2 SPINDLE OUT ==> ANALOG INPUT AI1
3 SPINDLE+ ==> 10V OUT VFD VS (jumper set so it gives +10V)
4
5 SPINDLE ENA- ==> DI1 / setting no 7: - Forward (FWD) running command terminal
6 SPINDLE ENA+ ==> +24V from vfd
7 SPINDLE DIR- ==> DI2 / setting no 8: - Reverse (REV)running command terminal
8 SPINDLE DIR+ ==> +24V from vfd
I can measure 10v between pin 1-3
And when starting spindle from linuxcnc voltages also adjusts according to speed. 10v=24000 rpm etc
But it just doesnt turn.
VFD display readout also adjusts to correct Hz. 24000 = 800 Hz when controlling speed from linuxcnc
VFD manual -
www.simphoenix.com/uploads/34a3ef73.pdf
Im guessing im missing some kind of enable.
Spindle INI section:
Code:
[SPINDLE_9]
P = 0
I = 0
D = 0
FF0 = 1
FF1 = 0
FF2 = 0
BIAS = 0
DEADBAND = 0
MAX_OUTPUT = 24000
OUTPUT_SCALE = 24000
OUTPUT_MIN_LIMIT = 3000
OUTPUT_MAX_LIMIT = 24000
HAL:
Code:
loadrt abs names=abs.spindle
loadrt lowpass names=lowpass.spindle
addf abs.spindle servo-thread
addf lowpass.spindle servo-thread
#*******************
# SPINDLE
#*******************
setp pid.s.Pgain [SPINDLE_9]P
setp pid.s.Igain [SPINDLE_9]I
setp pid.s.Dgain [SPINDLE_9]D
setp pid.s.bias [SPINDLE_9]BIAS
setp pid.s.FF0 [SPINDLE_9]FF0
setp pid.s.FF1 [SPINDLE_9]FF1
setp pid.s.FF2 [SPINDLE_9]FF2
setp pid.s.deadband [SPINDLE_9]DEADBAND
setp pid.s.maxoutput [SPINDLE_9]MAX_OUTPUT
setp pid.s.error-previous-target true
net spindle-index-enable <=> pid.s.index-enable
net spindle-enable => pid.s.enable
net spindle-vel-cmd-rpm => pid.s.command
net spindle-vel-fb-rpm => pid.s.feedback
net spindle-output <= pid.s.output
# ---setup spindle control signals---
net spindle-vel-cmd-rps <= spindle.0.speed-out-rps
net spindle-vel-cmd-rps-abs <= spindle.0.speed-out-rps-abs
net spindle-vel-cmd-rpm <= spindle.0.speed-out
net spindle-vel-cmd-rpm-abs <= spindle.0.speed-out-abs
net spindle-enable <= spindle.0.on
net spindle-cw <= spindle.0.forward
net spindle-ccw <= spindle.0.reverse
net spindle-brake <= spindle.0.brake
net spindle-revs => spindle.0.revs
net spindle-at-speed => spindle.0.at-speed
net spindle-vel-fb-rps => spindle.0.speed-in
net spindle-index-enable <=> spindle.0.index-enable
setp hm2_7i76e.0.7i76.0.0.spinout-minlim [SPINDLE_9]OUTPUT_MIN_LIMIT
setp hm2_7i76e.0.7i76.0.0.spinout-maxlim [SPINDLE_9]OUTPUT_MAX_LIMIT
setp hm2_7i76e.0.7i76.0.0.spinout-scalemax [SPINDLE_9]OUTPUT_SCALE
net spindle-output => hm2_7i76e.0.7i76.0.0.spinout
net spindle-enable => hm2_7i76e.0.7i76.0.0.spinena
net spindle-ccw => hm2_7i76e.0.7i76.0.0.spindir
# ---Setup spindle at speed signals---
sets spindle-at-speed true
Attachment not found
