linuxcnc pour plasma

The thcud component was added to 2.6.x, I don't think there is a sim for thcud.

What is the exact name of the sim your running(there are way too many)?

JT

tommylight wrote: I just checked, i have 2.7.4 on this computer and the sim version of THC has a some errors that need fixing, but i could not find the THCUD version, i thought it was included.
The plasma-thc-sim needs an ">" to be added at line 42 of simulator.hal or it will not start.
After starting it, it homes properly but it vont run in auto mode reporting errors about joint 2 limit switch and ferrors.
If i can make the changes due to time constraints, how do i go about uploading it?
By the looks of it, it is very similar to a thc300 version i had modified some time ago, or is it the same with the added voltage control?
There is also a mesa version for plasma-5i20 that works properly in simulator mode.
Maybe this could help, it is a working config for a simple THC with up/down/arcok signals.
forum.linuxcnc.org/forum/49-basic-config...hc-config-that-works

je n ai pas encore de thc j attend des composants pour en fabriquer une a base de arduino
www.guiacnc.com.br/plasma-267/thc-feito-com-aduino/75/
je pense qu elle fonctionne sur le principe THC avec haut / bas / arcok signal?

No eBay APP ID and/or Cert ID defined in Kunena configuration

BigJohnT wrote: The thcud component was added to 2.6.x, I don't think there is a sim for thcud.

What is the exact name of the sim your running(there are way too many)?

JT

tu parle de cette carte

tommylight wrote: I just checked, i have 2.7.4 on this computer and the sim version of THC has a some errors that need fixing, but i could not find the THCUD version, i thought it was included.
The plasma-thc-sim needs an ">" to be added at line 42 of simulator.hal or it will not start.
After starting it, it homes properly but it vont run in auto mode reporting errors about joint 2 limit switch and ferrors.
If i can make the changes due to time constraints, how do i go about uploading it?
By the looks of it, it is very similar to a thc300 version i had modified some time ago, or is it the same with the added voltage control?
There is also a mesa version for plasma-5i20 that works properly in simulator mode.
Maybe this could help, it is a working config for a simple THC with up/down/arcok signals.
forum.linuxcnc.org/forum/49-basic-config...hc-config-that-works

What is the exact name of the sim your talking about like sim/axis/etc?

JT

It is under sim/by_interface/parport/plasma-thc-sim.
That is the one with minor errors mentioned above.

tommylight wrote: It is under sim/by_interface/parport/plasma-thc-sim.
That is the one with minor errors mentioned above.

In 2.7.4 I see by_interface/paraport/plasma-thc-sim/plasma_mm and sure enough it does not load. I'll fix that. Yes the requirements for the <=, => and <=> were tightened up to only allow those combinations.

Thanks for letting me know.
JT

You are welcomed, and thank you for your never ending support and advice.
Tom

bonjour ,j ai fini ma table plasma et j ai finalement reussi a avoir l ecran avec la THC
mais je n arrive pas a enlever la le bouton d arret d urgence ????? donc je peux pas faire fonctionner les moteurs

je voudrais brancher ma THC sur les entrée de la carte
sur quel pin (UP,DOWN,ON) ?

have a look here, it is near the end of the thread
forum.linuxcnc.org/forum/49-basic-config...hc-config-that-works
Jetez un oeil ici, c'est près de la fin du fil

Vous devez également vérifier les broches d'entrée pour correspondre à votre configuration, comme ben vu sur votre image, vous devez changer la polarité d'entrée pour le commutateur de flotteur, arc ok et descendre.

you must also check the input pins to match your setup, as can ben seen in your picture you need to change the input polarity for float switch, arc ok and move down.