Qucik and easy kernel & linuxcnc install on Linux Mint 19.x

  • BeagleBrainz
  • Topic Author
  • New Member
  • New Member
More
6 years 7 months ago #160273 by BeagleBrainz
Qucik and easy kernel & linuxcnc install on Linux Mint 19.x was created by BeagleBrainz
This is for a Mint installation that does not already have a RT_PREEMPT kernel nor Linuxcnc installed.
ie a Virgin installation of Linux Mint 19.x

All kernel packages & linuxcnc packages are downloaded automatically from my google drive.

Download the attached file, open a terminal and in the directory you downloaded to run by
Code:
mv install-uspace.sh.txt install-uspace.sh
Code:
chmod +x install-uspace.sh
Code:
sudo ./install-uspace.sh

Then follow the prompts and off you go. Tested on Mint 19.2 XCFE, MATE should not be an issue.

Please Log in to join the conversation.

More
6 years 7 months ago #160276 by tommylight
Replied by tommylight on topic Qucik and easy kernel & linuxcnc install on Linux Mint 19.x

BeagleBrainz wrote:

Code:
sudo ./insta-uspace.sh

:S
Missing 2 L !

Please Log in to join the conversation.

  • BeagleBrainz
  • Topic Author
  • New Member
  • New Member
More
6 years 7 months ago #160277 by BeagleBrainz
Replied by BeagleBrainz on topic Qucik and easy kernel & linuxcnc install on Linux Mint 19.x
My excuse is The Toilet Paper Crisis sweeping Australia has affected me :P

Please Log in to join the conversation.

More
6 years 7 months ago #160279 by bevins
Replied by bevins on topic Qucik and easy kernel & linuxcnc install on Linux Mint 19.x
Yeah great. Just finishing the third linuxcnc on linux mint this weekend. Now you post this.

Attachment not found



Compiling preempt rt kernel.

Attachment not found

Please Log in to join the conversation.

  • BeagleBrainz
  • Topic Author
  • New Member
  • New Member
More
6 years 7 months ago #160284 by BeagleBrainz
Replied by BeagleBrainz on topic Qucik and easy kernel & linuxcnc install on Linux Mint 19.x
Oh you missed the the Mint respin with Linuxcnc already setup and ready for installation ?

forum.linuxcnc.org/9-installing-linuxcnc...with-linuxcnc#157411

Please Log in to join the conversation.

More
6 years 7 months ago #160286 by tommylight
Replied by tommylight on topic Qucik and easy kernel & linuxcnc install on Linux Mint 19.x
And you missed this
forum.linuxcnc.org/9-installing-linuxcnc...nd-easy-installation
But wait, i recall someone...........never mind ! :)

Please Log in to join the conversation.

More
6 years 7 months ago #160289 by bevins
Replied by bevins on topic Qucik and easy kernel & linuxcnc install on Linux Mint 19.x
Yeah I missed that. All that.

I got this down pat with JT's gnipsel page and note I have. It works everytime now, but it is long.

We need a webpage with this. not in the forum unless they sticky it.

Please Log in to join the conversation.

More
6 years 7 months ago #160291 by tommylight
Replied by tommylight on topic Qucik and easy kernel & linuxcnc install on Linux Mint 19.x

bevins wrote: We need a webpage with this. not in the forum unless they sticky it.

They are both sticky, under the installation section.

Please Log in to join the conversation.

More
6 years 7 months ago #160292 by bevins
Replied by bevins on topic Qucik and easy kernel & linuxcnc install on Linux Mint 19.x
Yeah, I missed all that. ok no loss. I am going to dig up another hard drive and create one of these dvd's and test it out and see how long it takes.

thanks......

Please Log in to join the conversation.

More
6 years 7 months ago #160293 by bevins
Replied by bevins on topic Qucik and easy kernel & linuxcnc install on Linux Mint 19.x
Looks like I will have a chance to try it out....

Attachment not found

Please Log in to join the conversation.

Time to create page: 0.119 seconds
Powered by Kunena Forum