Debian 10 LinuxCNC debuild -uc -us fails

:~$ uname -a
Linux fav 4.19.0-9-rt-amd64 #1 SMP PREEMPT RT Debian 4.19.118-2+deb10u1 (2020-06-07) x86_64 GNU/Linux
:~$

all steps successfully according to JT's Manual but finally

dpkg-buildpackage -us -uc -ui failed



Build Master_Documentation.pdf
built-in module pdftex registered
no support found for ifthen
no support found for ifxetex
no support found for fontspec
no support found for xltxtra
no support found for fontenc
no support found for inputenc
no support found for fancybox
built-in module makeidx registered
no support found for emc2
building additional files...
checking if compiling is necessary...
the output file doesn't exist
pdflatex -interaction=batchmode Master_Documentation.tex
pdflatex failed

A possible reason for transformation failure is invalid DocBook
(as reported by xmllint)

Error: pdflatex compilation failed

make[1]: *** [../docs/src/Submakefile:448: ../docs/src/Master_Documentation.pdf] Fehler 1
make[1]: Verzeichnis „/home/eruepe/emc/src“ wird verlassen
make: *** [debian/rules:36: build-stamp] Fehler 2
dpkg-buildpackage: Fehler: Unterprozess debian/rules build lieferte Exitstatus 2
debuild: fatal error at line 1182:
dpkg-buildpackage -us -uc -ui failed

forum.linuxcnc.org/9-installing-linuxcnc...ick-and-easy-install

This variant I've tried once before, with success, but last time something did also not work properly herewith, I'll try it again! Also with mint 19.2 it was a short and easy way to success! When I tried an installation on raspberry pi4 I've finally learned to use git - and debian would fit me almost better. I found ASUS J4005I-C later, with extremely good performance, also small enough to fit behind a tiny 10 inch elo touchscreen.

Fine running LinuxCNC 2.7.15 with Stretch does not support full graphic resolution 1280 x 800 on elo screen wit this ASUS J4005I-C mainboard, so I'm looking now around, how to get it with buster!

Let us know if something does not work.

AFTER DEBIAN INSTALLATION

e@f:~$ uname -a
Linux f 4.19.0-9-amd64 #1 SMP Debian 4.19.118-2 (2020-04-29) x86_64 GNU/Linux

THEN ACCORDING TO INSTRUCTIONS

e@f:~$ cd Downloads
e@f:~/Downloads$ sudo chmod +x install.sh
e@f:~/Downloads$ ./install.sh
Hit:1 security.debian.org/debian-security buster/updates InRelease
Hit:2 deb.debian.org/debian buster InRelease
Hit:3 deb.debian.org/debian buster-updates InRelease
Reading package lists... Done
Reading package lists... Done
Building dependency tree
Reading state information... Done
Note, selecting 'linux-headers-4.19.0-9-rt-amd64' for regex 'linux-headers-4.19.0-9-rt'
The following additional packages will be installed:
diffstat gdebi-core gettext gir1.2-vte-2.91 intltool-debian libapt-pkg-perl libarchive-zip-perl libasync-mergepoint-perl libcapture-tiny-perl
libcgi-fast-perl libcgi-pm-perl libclass-accessor-perl libclone-perl libdigest-bubblebabble-perl libdigest-hmac-perl libemail-valid-perl
......
......
......

Building dependency tree
Reading state information... Done
E: Unable to locate package linuxcnc-uspace
Finshed, you can reboot your PC now.
e@f:~/Downloads$ ^C



AFTER REBOOT

e@f:~$ uname -a
Linux f 4.19.0-9-rt-amd64 #1 SMP PREEMPT RT Debian 4.19.118-2+deb10u1 (2020-06-07) x86_64 GNU/Linux
e@f:~$

e@f:~$ linuxcnc
bash: linuxcnc: command not found
e@f:~$

Executing: /tmp/apt-key-gpghome.d7RjB1OI3g/gpg.1.sh --keyserver hkp://keys.gnupg.net --recv-key EF1B07FEE0EE663E
gpg: keyserver receive failed: No route to host
Hit:1 deb.debian.org/debian buster InRelease
Hit:2 security.debian.org/debian-security buster/updates InRelease
Hit:3 deb.debian.org/debian buster-updates InRelease
Get:4 buildbot.linuxcnc.org buster InRelease [37.8 kB]
Err:4 buildbot.linuxcnc.org buster InRelease
The following signatures couldn't be verified because the public key is not available: NO_PUBKEY EF1B07FEE0EE663E
Reading package lists... Done
W: GPG error: buildbot.linuxcnc.org buster InRelease: The following signatures couldn't be verified because the public key is not available: NO_PUBKEY EF1B07FEE0EE663E

Try this for the keyserver:
sudo apt-key adv --keyserver hkp://keys.gnupg.net:80 --recv-key EF1B07FEE0EE663E

it works perfectly, thank you very much

Nice, you are welcomed.

partec wrote: :~$ uname -a
Linux fav 4.19.0-9-rt-amd64 #1 SMP PREEMPT RT Debian 4.19.118-2+deb10u1 (2020-06-07) x86_64 GNU/Linux
:~$

all steps successfully according to JT's Manual but finally

dpkg-buildpackage -us -uc -ui failed



Build Master_Documentation.pdf
built-in module pdftex registered
no support found for ifthen
no support found for ifxetex
no support found for fontspec
no support found for xltxtra
no support found for fontenc
no support found for inputenc
no support found for fancybox
built-in module makeidx registered
no support found for emc2
building additional files...
checking if compiling is necessary...
the output file doesn't exist
pdflatex -interaction=batchmode Master_Documentation.tex
pdflatex failed

A possible reason for transformation failure is invalid DocBook
(as reported by xmllint)

Error: pdflatex compilation failed

make[1]: *** [../docs/src/Submakefile:448: ../docs/src/Master_Documentation.pdf] Fehler 1
make[1]: Verzeichnis „/home/eruepe/emc/src“ wird verlassen
make: *** [debian/rules:36: build-stamp] Fehler 2
dpkg-buildpackage: Fehler: Unterprozess debian/rules build lieferte Exitstatus 2
debuild: fatal error at line 1182:
dpkg-buildpackage -us -uc -ui failed

same as my error,, it seems u cant built it from source using debian