Linuxcnc 2.9.2 and 2.93 images for Raspberry Pi 4b & 5

More
2 years 9 months ago #289612 by der hobbyist
Replied by der hobbyist on topic Linuxcnc 2.9.2 for Raspberry Pi 4 & 5 images
Hi,
I found another small bug. Then I change a tool the icons of the desktop menu become visible (see picture below).

Please Log in to join the conversation.

More
2 years 9 months ago #289634 by rodw
Replied by rodw on topic Linuxcnc 2.9.2 for Raspberry Pi 4 & 5 images

Hi,
I found another small bug. Then I change a tool the icons of the desktop menu become visible (see picture below).
That is nothing to do with the installation process. I can't help. Report in the correct GUI section

Please Log in to join the conversation.

More
2 years 9 months ago #289644 by Cant do this anymore bye all
Replied by Cant do this anymore bye all on topic Linuxcnc 2.9.2 for Raspberry Pi 4 & 5 images

Hi,
I found another small bug. Then I change a tool the icons of the desktop menu become visible (see picture below).
 
That's normal behaviour for the bottom panel in Debian for  XFCE (for amd64 & arm64) when you move the mouse over the area where the panel would be no matter the application you are using, if you right click on the panel you can change the properties. Not a bug & does not require reporting.

Please Log in to join the conversation.

More
2 years 9 months ago #289646 by rodw
Replied by rodw on topic Linuxcnc 2.9.2 for Raspberry Pi 4 & 5 images
Aah, now I know what you were looking at. an XFCE feature

Please Log in to join the conversation.

More
2 years 9 months ago #289978 by cauldron_boy
Replied by cauldron_boy on topic Linuxcnc 2.9.2 for Raspberry Pi 4 & 5 images
Installed on a Pi5 8Gb.
Running great with a Mesa 7i76e

Please Log in to join the conversation.

More
2 years 9 months ago #290411 by Calysto
Replied by Calysto on topic Linuxcnc 2.9.2 for Raspberry Pi 4 & 5 images
I have an older image installed on my PI, with 2.9.1. The normal update/upgrade procedure won't help. Can I upgrade to this 'image'?

Please Log in to join the conversation.

More
2 years 9 months ago #290413 by rodw
Replied by rodw on topic Linuxcnc 2.9.2 for Raspberry Pi 4 & 5 images
Install the 2.9.2 image from the downloads page
If its a Pi 5, this image is likely better but you need o use Balena Etcher to burn it to an SD card as the rpi imager does not like it.
drive.google.com/drive/folders/1NfRV8bho...3VXtN?usp=drive_link
This has been fixed upstream but I have not had time to rebuild it

Please Log in to join the conversation.

More
2 years 9 months ago #290414 by Calysto
Replied by Calysto on topic Linuxcnc 2.9.2 for Raspberry Pi 4 & 5 images
Hmm... then I have to re-install all the rest.... might do that later...

Pi4

Please Log in to join the conversation.

More
2 years 9 months ago #290759 by U2fletch
Replied by U2fletch on topic Linuxcnc 2.9.2 for Raspberry Pi 4 & 5 images
I have a Pi 400 and the image loads fine. I have sound, and can confirm that it runs great on my setup.  Had a minor hiccup with my Mesa 7i96s board. I could ping the board at address 10.10.10.10, but when I started LinuxCNC I got the "temporarily unavaliable" error. Had to go configure my network settings. Once that was set everything works great.  Thanks!

Please Log in to join the conversation.

More
2 years 8 months ago #292108 by itai
Replied by itai on topic Linuxcnc 2.9.2 for Raspberry Pi 4 & 5 images
Hi,
I want to use Raspberry PI 4 + LinuxCNC-RIO (Tangoboard) with SPI connection.
How can I enable SPI (using the IO pins) with the LinuxCNC image?
How can I disable the automatic screen lock?

Thanks,
-- Itai

 

Please Log in to join the conversation.

Time to create page: 0.125 seconds
Powered by Kunena Forum