setting up for Parallel port Tutoral Part 3

More
10 years 2 months ago #79585 by cncbasher
Replied by cncbasher on topic setting up for Parallel port Tutoral Part 3
Dinyo:
your a bit sparse on details , we need to know , what the charge pump requirements are , is this for a mesa 5i25 or parallel port etc
but yes pathpilot does have a chargepump , Classic ladder is part of lcnc so should also be in pathpilot , but again easily added .

Please Log in to join the conversation.

More
10 years 2 months ago #79590 by dinkata
Replied by dinkata on topic setting up for Parallel port Tutoral Part 3

we need to know

thanks for the reply
1."Chargepump" is necessary for paralel port .Configuration parallel port ,step motor Geckodrive G540.
2.ClassicLadder is necessary for configuration 5i25 + 7i77 .
Can you help me for two things ?

Please Log in to join the conversation.

More
10 years 2 months ago #79591 by cncbasher
Replied by cncbasher on topic setting up for Parallel port Tutoral Part 3
Treat the chargepump exactly the same as for linuxcnc , chargepump.comp is included in pathpilot
as is classicladder , so if you have a config for linuxcnc , you should be able to copy the approprate sections across.

Please Log in to join the conversation.

More
10 years 2 months ago #79592 by dinkata
Replied by dinkata on topic setting up for Parallel port Tutoral Part 3
in hal ....# loadrt charge_pump .... run normal .
in hal only .... loadrt charge_pump ...error
Code:
......... Starting LinuxCNC IO program: io io started halcmd loadusr io started Starting HAL User Interface program: halui halcmd loadusr -Wn halui halui -ini /home/operator/tmc/configs/tormach_mill/mill_pp.ini mill_pp.hal:10: Can't find module 'charge_pump' in /home/operator/tmc/rtlib Shutting down and cleaning up LinuxCNC... 2271 Killing linuxcncsvr Killing task linuxcncsvr, PID=2271 .......................................

Please Log in to join the conversation.

More
10 years 2 months ago #79594 by cncbasher
Replied by cncbasher on topic setting up for Parallel port Tutoral Part 3
check that charge_pump.ko is in /tmc/rtlib
it also should be used in base thread

it may be the version you have has not had chargepump added to the compiled source
please kindly attach your ini & hal file ,

which version of pathpilot are your using

Please Log in to join the conversation.

More
10 years 2 months ago #79595 by dinkata
Replied by dinkata on topic setting up for Parallel port Tutoral Part 3

cncbasher wrote: check that charge_pump.ko is in /tmc/rtlib

There is no such file charge_pump.ko

which version of pathpilot are your using

instal 1.9.2b and upgrade 1.9.6b

Please Log in to join the conversation.

More
10 years 2 months ago #79597 by dinkata
Replied by dinkata on topic setting up for Parallel port Tutoral Part 3

Attachment not found



Attachment not found

Please Log in to join the conversation.

More
10 years 2 months ago #79600 by dinkata
Replied by dinkata on topic setting up for Parallel port Tutoral Part 3
:woohoo: :woohoo: :woohoo:
thank you , in test runs , later check of machine .
Best regards
Dinyo

Please Log in to join the conversation.

More
9 years 9 months ago #85271 by X123
Replied by X123 on topic setting up for Parallel port Tutoral Part 3
HI,
I'm new to Pathpilot and just acquired a disk for it.
Read as many install tutorials I could find but I'm baffled. Left shift and left alt doesn't work when the splash screen shows up. After a few seconds it goes right to " Mesa interface card not detected.....etc."
Tried several times but no luck.
Would appreciate any suggestion on how to get past that.
Thanks, Fritz.

Please Log in to join the conversation.

More
9 years 9 months ago #85275 by cncbasher
Replied by cncbasher on topic setting up for Parallel port Tutoral Part 3
theirs a number of things this can be , however my guess is your using an old motherboard and perhaps a USB or wifi keyboard , use a ps2 keyboard and it should work fine , then once the settings have changed to the USB keyboard , then you should be ok . this is more to do with motherboard bios and OS , than pathpilot it's self .

Please Log in to join the conversation.

Time to create page: 0.207 seconds
Powered by Kunena Forum