Stuck

jnwinkie
Topic Author
Offline
Senior Member

6 years 1 week ago #187058 by jnwinkie

Replied by jnwinkie on topic Stuck

Thanks Tom;

So it sounds like I have a failed build. Do I approach the finance minister for a new plasma cutter that supports THC? If so which one would be best?

PlasmaC still curious?

No sure where to from here.

Cheers

John

Please Log in to join the conversation.

jnwinkie
Topic Author
Offline
Senior Member

6 years 1 week ago #187059 by jnwinkie

Replied by jnwinkie on topic Stuck

Thanks Rod;
Humidity in Vic is not too bad, but will explore a drier. Maybe a moot point if I can't get the thing to cut!

Thanks again for your feedback.

Cheers.

John

Please Log in to join the conversation.

tommylight
Away
Administrator

6 years 1 week ago #187075 by tommylight

Replied by tommylight on topic Stuck

jnwinkie wrote:
So it sounds like I have a failed build. Do I approach the finance minister for a new plasma cutter that supports THC? If so which one would be best?

Not really, i mostly use older hand manual plasma cutters modified for machine cutting, so most probably yours can be modified too.
You do need a THC, preferably the Mesa THCAD 10 and two 1MOhm resistors, a reed switch, some wires and two relays.

Please Log in to join the conversation.

jnwinkie
Topic Author
Offline
Senior Member

6 years 6 days ago #187157 by jnwinkie

Replied by jnwinkie on topic Stuck

Thanks Tom;

What do you to covert torch to machine torch or not? I found cut speed helped, a lot slower that on the box. More like 700mm/min.
Will the THCAD work with parallel BoB?

Thanks
John

Please Log in to join the conversation.

rodw
Offline
Platinum Member

6 years 6 days ago #187159 by rodw

Replied by rodw on topic Stuck

John, yes you can use the software encoder component with a BOB and a THCAD. It is a bit less precision that way. Tommy will know more as he's done a couple. I think he used 2 x BOB's

See linuxcnc.org/docs/2.8/html/man/man9/encoder.9.html

Please Log in to join the conversation.

tommylight
Away
Administrator

6 years 5 days ago #187211 by tommylight

Replied by tommylight on topic Stuck

Yes the Mesa THCAD does work with a parallel port as i had two of them working, one is still in use every day from the start of this year and never had a single issue, the other was in use about 2 months till i got the Mesa 7i92, so now i have 2 of THCAD connected directly to Mesa 7i92 inputs, both in use daily.

Please Log in to join the conversation.

jnwinkie
Topic Author
Offline
Senior Member

6 years 5 days ago #187257 by jnwinkie

Replied by jnwinkie on topic Stuck

Thanks all;
Some success, I cut these castor plates from 3mm sheet.
I had some dross but it came away with a light tap from a hammer.
I think the speed can be increased slightly, it is currently at 700mm/sec but suspect it could go up to about 900mm/sec.

Cheers
John

Please Log in to join the conversation.

rodw
Offline
Platinum Member

6 years 5 days ago #187263 by rodw

Replied by rodw on topic Stuck

if you can knock the dross off you are pretty close to perfect. There should be almost none. Read up on high speed dross and low speed dross.

Please Log in to join the conversation.

jnwinkie
Topic Author
Offline
Senior Member

6 years 5 days ago #187264 by jnwinkie

Replied by jnwinkie on topic Stuck

Thanks Rod;

I have looked it up and I am getting straight lines rather than the slightly S shaped cut lines as described on the hyperthem site. How do those plates look to you?

www.hypertherm.com/support/system-suppor...lity/too-much-dross/

Cheers

John

Please Log in to join the conversation.

CBEAR
Offline
Senior Member

6 years 5 days ago #187292 by CBEAR

Replied by CBEAR on topic Stuck

I'd probably drop your cut height to 1.55mm or .060" and slow down the cut speeds to like 80% of what you are currently cutting at and see what happens

Please Log in to join the conversation.

Time to create page: 0.148 seconds