PlasmaC Just using pierce for circle centre

Clive S wrote: Phill

Not sure what I am doing wrong but I still can not get it to centre spot without the drill

When you get the time would you mind looking at it ?

Attachment not found

I loaded the file as is, so the T1: drill operation was selected then ran the PP and it worked.

I then tried with the T7: Centre Spot, I needed to edit the operation and set the "Lead" in to Perpendicular and "Start at the centre of circles smaller than" to 40mm and it worked.

You cannot use a drill tool (T1: drill) because you need a pierce height.

phillc54 wrote:

Clive S wrote: Phill

Not sure what I am doing wrong but I still can not get it to centre spot without the drill

When you get the time would you mind looking at it ?

Attachment not found

I loaded the file as is, so the T1: drill operation was selected then ran the PP and it worked.

I then tried with the T7: Centre Spot, I needed to edit the operation and set the "Lead" in to Perpendicular and "Start at the centre of circles smaller than" to 40mm and it worked.

You cannot use a drill tool (T1: drill) because you need a pierce height.

Phill Sorry it must be me being dumb. I take it then I can't use drill for the reasons stated.

So T7:Centre Spot, should work I edited the "lead" in to Perpendicular but can't seem to find the "Start at the centre of circles smaller than" bit. where will I find that?

To be clear I only have the "PP version E" loaded and not the "minimal.tools" if I need that where do I put it ?

Thanks for your continued help

So T7:Centre Spot, should work I edited the "lead" in to Perpendicular but can't seem to find the "Start at the centre of circles smaller than" bit. where will I find that?

Double click on the operation and it is two lines from the bottom in the dialog

To be clear I only have the "PP version E" loaded and not the "minimal.tools" if I need that where do I put it ?

You don't for this but if you do need them they go in your toolset file.


EDIT: why not just use the drill operation?

phillc54 wrote:

So T7:Centre Spot, should work I edited the "lead" in to Perpendicular but can't seem to find the "Start at the centre of circles smaller than" bit. where will I find that?

Double click on the operation and it is two lines from the bottom in the dialog

To be clear I only have the "PP version E" loaded and not the "minimal.tools" if I need that where do I put it ?

You don't for this but if you do need them they go in your toolset file.

EDIT: why not just use the drill operation?

You said "You cannot use a drill tool (T1: drill) because you need a pierce height."

Re. " Double click on the operation and it is two lines from the bottom in the dialog"

In the "operation tab" There is a "G insert code" box !! I am just not getting what you are asking me to do

In the operation tab double click on the "No Offset, Big circle,T5: Jet tool" operation


Edit: But you can use a Jet tool on a Drill operation.

phillc54 wrote: In the operation tab double click on the "No Offset, Big circle,T5: Jet tool" operation


Edit: But you can use a Jet tool on a Drill operation.

Ok Phill I think I get it now.

Under "operation" select Drilling, then pick Jet tool, min hole size 3mm - Max hole size 70mm

It seems to work with the sim and the code looks like it will do it. I will now go and test it on the machine.

Thanks for you patience

I am have a problem with pierce with the torch not firing hypertherm 45 the machine is generally running fine.

We want to pierce through at the hole centre so have used a drill operation but the torch does not fire.

I have attached the sheetcam job file (just two holes to test) and the gcode

Can anybody throw any light on this please

Video would be very helpful .

I just ran your config as a sim and ran that gcode file and it all looked good here.The Torch On LED lit which indicates the torch output from the component works.
Run Halshow and put a watch on hm2_7i96.0.ssr.00.out-00 to confirm that it gets the signal.

phillc54 wrote: I just ran your config as a sim and ran that gcode file and it all looked good here.The Torch On LED lit which indicates the torch output from the component works.
Run Halshow and put a watch on hm2_7i96.0.ssr.00.out-00 to confirm that it gets the signal.

Phil I ran this on my machine as the other is 50 miles away. We have more or less the same config.
is this the correct plot:


Also could it be that just the small move in the code is the culprit