Well, this is a bit strange, I managed to build a RIP in another folder ~/linuxcnc-pla and when it loads, I get these messages despite both settings being in the ini file.
<commandline>:0: Pin 'ini.z.max_limit' does not exist
<commandline>:0: Pin 'ini.z.min_limit' does not exist
Just after that I get
hm2/hm2_7i76e.0: error finishing read! iter=3073
I know that shuts down Linuxcnc but I've never seen this before so here is the output
Code:
plasma2@plasma2:~$ halcmd show param *tmax
Parameters:
Owner Type Dir Value Name
68 s32 RW 1320 abs.0.tmax
38 s32 RW 1920 and2.0.tmax
38 s32 RW 1368 and2.1.tmax
38 s32 RW 960 and2.2.tmax
38 s32 RW 816 and2.3.tmax
38 s32 RW 1104 and2.4.tmax
38 s32 RW 11328 and2.5.tmax
38 s32 RW 1104 and2.6.tmax
38 s32 RW 792 and2.7.tmax
38 s32 RW 624 and2.8.tmax
47 s32 RW 1608 conv-float-s32.0.tmax
50 s32 RW 0 conv-s32-bit.0.tmax
95 s32 RW 1344 db_arc-ok.tmax
95 s32 RW 1224 db_breakaway.tmax
95 s32 RW 1944 db_float.tmax
95 s32 RW 936 db_ohmic.tmax
23 s32 RW 1728 estop-latch.0.tmax
23 s32 RW 10944 estop-latch.1.tmax
23 s32 RW 1200 estop-latch.2.tmax
23 s32 RW 912 estop-latch.3.tmax
83 s32 RW 0 hm2_7i76e.0.read-request.tmax
83 s32 RW 1693200 hm2_7i76e.0.read.tmax
83 s32 RW 106896 hm2_7i76e.0.write.tmax
62 s32 RW 3240 ilowpass.0.tmax
19 s32 RW 6456 motion-command-handler.tmax
19 s32 RW 76896 motion-controller.tmax
65 s32 RW 840 mult2.0.tmax
65 s32 RW 1152 mult2.1.tmax
65 s32 RW 1296 mult2.2.tmax
65 s32 RW 1032 mult2.3.tmax
71 s32 RW 1632 mux2.0.tmax
71 s32 RW 720 mux2.1.tmax
53 s32 RW 1776 mux4.0.tmax
56 s32 RW 1464 mux8.0.tmax
74 s32 RW 1176 not.0.tmax
89 s32 RW 4704 ohmicsense.tmax
29 s32 RW 1368 or2.0.tmax
29 s32 RW 888 or2.1.tmax
29 s32 RW 1080 or2.2.tmax
29 s32 RW 10344 or2.3.tmax
29 s32 RW 816 or2.4.tmax
29 s32 RW 1032 or2.5.tmax
86 s32 RW 2784 pid.s.do-pid-calcs.tmax
86 s32 RW 11232 pid.x.do-pid-calcs.tmax
86 s32 RW 2376 pid.y.do-pid-calcs.tmax
86 s32 RW 2088 pid.y2.do-pid-calcs.tmax
86 s32 RW 11280 pid.z.do-pid-calcs.tmax
92 s32 RW 14304 plasmac.tmax
59 s32 RW 1248 select8.0.tmax
20 s32 RW 1767576 servo-thread.tmax
35 s32 RW 12696 siggen.0.update.tmax
80 s32 RW 1536 stepboost.0.tmax
77 s32 RW 3168 thcad10.tmax
41 s32 RW 1584 toggle.0.tmax
44 s32 RW 1392 toggle2nist.0.tmax
32 s32 RW 840 xor2.0.tmax
Ping is
Code:
plasma2@plasma2:~$ ping 10.10.10.10
PING 10.10.10.10 (10.10.10.10) 56(84) bytes of data.
64 bytes from 10.10.10.10: icmp_seq=1 ttl=64 time=0.103 ms
64 bytes from 10.10.10.10: icmp_seq=2 ttl=64 time=0.106 ms
64 bytes from 10.10.10.10: icmp_seq=3 ttl=64 time=0.105 ms
64 bytes from 10.10.10.10: icmp_seq=4 ttl=64 time=0.103 ms
and I have set the coalescing. not sure if it was required or not but it did improve ping time marginally.
Latency is not an issue.
Attachment not found
Is there something with QT or QTplasmac that needs reinstalling in the new RIP installation? It would seem the overrun is due to the software (QT/QTplasmac)
