Mesa 7i92 board problem

1.Hi, I got my self a new 7i92 board and is not working properly I have changed the IP address to 10.10.10.10 but if I ping 10.10.10.10 it working correctly.
my IP address for the setup was 10.10.10.11 gateway 10.10.10.1 and my netmask 8. If I try to do 
mesaflash --device 7i92 --readhmid and
mesaflash --device 7i92 --addr 10.10.10.10 --readhmidIs saying no 7i92 board  found, but I have set My pncconfwizard and X , Y and Z are
moving correct but input and output pins not working.
 

aabtech wrote:

1.Hi, I got my self a new 7i92 board and is not working properly I have changed the IP address to 10.10.10.10 but if I ping 10.10.10.10 it working correctly.
my IP address for the setup was 10.10.10.11 gateway 10.10.10.1 and my netmask 8. If I try to do 
mesaflash --device 7i92 --readhmid and
mesaflash --device 7i92 --addr 10.10.10.10 --readhmidIs saying no 7i92 board  found, but I have set My pncconfwizard and X , Y and Z are
moving correct but input and output pins not working.

 
You have readhmidIs
Try mesaflash --device 7i92 --addr 10.10.10.10 --readhmid

Also, all pins not used for stepgen/pwm will be set as inputs, to use them as outputs they must be set as such in hal, or in PncConf.

I have done that but my limit switch , float switch , touch on, not working. And I want to know setting up like this do I have to go to HAL and like the output and input if so how ?

 

Are you sure you have the BOB pin mapping correct?

for the "5 axis Mach BOB" , the mapping is

IO Connections for P2
Pin# I/O Pri. func Sec. func Chan Sec. Pin func Sec. Pin Dir

Spindle-PWM 0 IOPort PWM 0 PWM (Out)
Drive-Enable 1 IOPort None
X-Step 2 IOPort StepGen 0 Step/Table1 (Out)
Input-P15 3 IOPort None
X-Dir 4 IOPort StepGen 0 Dir/Table2 (Out)
B-Step 5 IOPort StepGen 8 Step/Table1 (Out)
Y-Step 6 IOPort StepGen 1 Step/Table1 (Out)
B-Dir,Relay 7 IOPort StepGen 8 Dir/Table2 (Out)
Y-Dir 8 IOPort StepGen 1 Dir/Table2 (Out)
Z-Step 9 IOPort StepGen 2 Step/Table1 (Out)
Z-Dir 10 IOPort StepGen 2 Dir/Table2 (Out)
A-Step 11 IOPort StepGen 3 Step/Table1 (Out)
A-Dir 12 IOPort StepGen 3 Dir/Table2 (Out)
Input-P10 13 IOPort None
Input-P11 14 IOPort QCount 0 Quad-A (In)
Input-P12 15 IOPort QCount 0 Quad-B (In)
Input-P13 16 IOPort QCount 0 Quad-IDX (In)

How to use Input-P10 13 IOPort None
because it is not showing in PNCconfig?

Those would be GPIO 13,14,15,16
in the hal file:

hm2_7i92.0.013.in
hm2_7i92.0.014.in
hm2_7i92.0.015.in
hm2_7i92.0.016.in

and

hm2_7i92.0.013.in_not
hm2_7i92.0.014.in_not
hm2_7i92.0.015.in_not
hm2_7i92.0.016.in_not