Ref Z references X axis

Hi,

I just installed probe_basic and ran into the problem, that when pressing the Ref Z button, my CNC references the X Axis. When I change the .ini file to gmoccapy being the UI it does not do this, so I asume it has to do with probe basic. When pressing the home all axis button everything works and each axis is homed in the correct order.

Is this a known bug or does anybody know how to fix this?

Thanks,

Max

mf290997 wrote: Hi,

I just installed probe_basic and ran into the problem, that when pressing the Ref Z button, my CNC references the X Axis. When I change the .ini file to gmoccapy being the UI it does not do this, so I assume it has to do with probe basic. When pressing the home all axis button everything works and each axis is homed in the correct order.

Is this a known bug or does anybody know how to fix this?

Thanks,

Max

sounds like your ini file is incorrectly listed for the axis number. x, y, z = 0, 1, 2

WHat exactly do you mean? Are you sure about that? Because the same button in gmoccapy does the correct thing.

as shown here it is done by joints and joint 0 is X, joint 1 is Y, joint 2 is Z

```
[KINS]
KINEMATICS = trivkins coordinates=XYZAB
JOINTS = 5

#==================
# X Axis
#==================

[AXIS_X]
MIN_LIMIT = -0.001
MAX_LIMIT = 17.000
MAX_VELOCITY = 10.0
MAX_ACCELERATION = 20.0

[JOINT_0]
TYPE = LINEAR
HOME = 0.000
MAX_VELOCITY = 10
MAX_ACCELERATION = 20.0
BACKLASH = 0.003
INPUT_SCALE = 4000
OUTPUT_SCALE = 1.000
MIN_LIMIT = -0.001
MAX_LIMIT = 17.0
FERROR = 0.050
MIN_FERROR = 0.010
HOME_OFFSET = 0.0
HOME_SEARCH_VEL = 1.0
HOME_LATCH_VEL = 0.1
HOME_USE_INDEX = NO
HOME_IGNORE_LIMITS = NO
HOME_SEQUENCE = 1
HOME_IS_SHARED = 1

#==================
# Y Axis
#==================

[AXIS_Y]
MIN_LIMIT = -0.001
MAX_LIMIT = 8.500
MAX_VELOCITY = 10.0
MAX_ACCELERATION = 20.0

[JOINT_1]
TYPE = LINEAR
HOME = 0.000
MAX_VELOCITY = 10
MAX_ACCELERATION = 20.0
BACKLASH = 0.003
INPUT_SCALE = 4000
OUTPUT_SCALE = 1.000
MIN_LIMIT = -0.001
MAX_LIMIT = 8.500
FERROR = 0.050
MIN_FERROR = 0.010
HOME_OFFSET = 0.0
HOME_SEARCH_VEL = 1.0
HOME_LATCH_VEL = 0.1
HOME_USE_INDEX = NO
HOME_IGNORE_LIMITS = NO
HOME_SEQUENCE = 1
HOME_IS_SHARED = 1

#==================
# Z Axis
#==================

[AXIS_Z]
MIN_LIMIT = -15.750
MAX_LIMIT = 0.001
MAX_VELOCITY = 10
MAX_ACCELERATION = 20.0

[JOINT_2]
TYPE = LINEAR
HOME = 0.000
MAX_VELOCITY = 10
MAX_ACCELERATION = 20.0
BACKLASH = 0.003
INPUT_SCALE = 4000
OUTPUT_SCALE = 1.000
MIN_LIMIT = -15.750
MAX_LIMIT = 0.001
FERROR = 0.050
MIN_FERROR = 0.010
HOME_OFFSET = 1.0
HOME_SEARCH_VEL = 1.0
HOME_LATCH_VEL = 0.1
HOME_USE_INDEX = NO
HOME_IGNORE_LIMITS = NO
HOME_SEQUENCE = 0
HOME_IS_SHARED = 1

Hm, I think I got that correct... Tomorrow I'll be able to post my files.

I'm pretty sure, here is the button and its command, if you are having something happen other than the x axis move then i would suspect the config. this shows it is referencing the x axis as defined in your config.

The issue is only present when pressing the REF Z button. Where can I find these configs shown in the screenshot? or can yo check if the REF Z button says machine.home.axis:z?

perhaps your ini and hal files are mixed up?

Thanks. I'll post my files tomorrow.